Unfired pressure vessels - Part 3: Design

Vessels on brackets- Revision of clause 16

Unbefeuerte Druckbehälter - Teil 3: Konstruktion

Récipients sous pression non soumis à la flamme - Partie 3 : Conception

Nekurjene tlačne posode - 3. del: Konstruiranje - Dopolnilo A16

General Information

Status
Not Published
Publication Date
03-Aug-2021
Withdrawal Date
03-Feb-2022
Current Stage
4097 - End of interruption of work - split/merged
Completion Date
10-Nov-2021

Relations

Buy Standard

Draft
EN 13445-3:2014/oprA16:2019
English language
42 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 13445-3:2014/oprA16:2019
01-november-2019
Neogrevane (nekurjene) tlačne posode - 3. del: Konstruiranje - Dopolnilo A16
Unfired pressure vessels - Part 3: Design
Unbefeuerte Druckbehälter - Teil 3: Konstruktion
Récipients sous pression non soumis à la flamme - Partie 3 : Conception
Ta slovenski standard je istoveten z: EN 13445-3:2014/prA16
ICS:
23.020.32 Tlačne posode Pressure vessels
SIST EN 13445-3:2014/oprA16:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 13445-3:2014/oprA16:2019

---------------------- Page: 2 ----------------------
SIST EN 13445-3:2014/oprA16:2019


DRAFT
EUROPEAN STANDARD
EN 13445-3:2014
NORME EUROPÉENNE

EUROPÄISCHE NORM
prA16
October 2019
ICS 23.020.30
English Version

Unfired pressure vessels - Part 3: Design
Récipients sous pression non soumis à la flamme - Unbefeuerte Druckbehälter - Teil 3: Konstruktion
Partie 3 : Conception
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 54.

This draft amendment A16, if approved, will modify the European Standard EN 13445-3:2014. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13445-3:2014/prA16:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 13445-3:2014/oprA16:2019
EN 13445-3:2014/prA16:2019 (E)
Contents Page
European foreword . 3
1 Modification to 7.6.5, Junctions - general . 4
2 Modification to Clause 16, Additional non-pressure loads . 4
3 Modifications to 16.6.2, Additional specific symbols and abbreviations . 4
4 Modifications to 16.6.8, Single line loads (see Figures 16.6-2 and 16.6-3) . 4
5 Modification to 16.7.5, Load limits for shell . 5
6 Modification to 16.10.1, General . 5
7 Modifications to 16.10.2, Additional specific symbols and abbreviations (see Figure
16.10-1) . 5
8 Modification to 16.10.3, Conditions of applicability. 11
9 Modifications to 16.10.4, Applied forces . 11
10 Modifications to 16.10.5, Load limits of the shell . 16
11 Addition of a new Subclause 16.10.6, Support brackets . 24
12 Addition of a new Subclause 16.10.7, Design of welds . 28
13 Modifications to 16.12.5.4.2, General condit
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.