Open end blind rivets with break pull mandrel and countersunk head - AIA/St (ISO 15978:2002)
ISO 15978 specifies dimensional and mechanical characteristics and application data for open end blind rivets with break pull mandrel and countersunk head, with an aluminium alloy body and a steel mandrel with nominal diameters from 2,4 mm up to and including 5 mm.
Offene Blindniete mit Sollbruchdorn und Senkkopf - AIA/St (ISO 15978:2002)
Diese Internationale Norm legt Maße und mechanische Eigenschaften sowie Anwendungsdaten für offene Blindniete mit Sollbruchdorn und Senkkopf, mit einer Niethülse aus Aluminiumlegierung (AlA) und einem Nietdorn aus Stahl (St) und mit Nenndurchmessern, d, von 2,4 mm bis 4,8 mm fest.
Rivets aveugles à rupture de tige à corps ouvert, à tête fraisée - AIA/St (ISO 15978:2002)
L'ISO 15978:2002 spécifie les caractéristiques dimensionnelles et mécaniques ainsi que les données d'application pour les rivets aveugles à rupture de tige à corps ouvert, à tête fraisée, avec un corps en alliage d'aluminium (AlA) et une tige en acier (St), de diamètre nominal compris entre 2,4 mm et 5 mm inclus.
Slepe votle kovice z zarezanim zakovnim trnom in ugrezno glavo -AlA/St (ISO 15978:2002)
Standards Content (sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Slepe votle kovice z zarezanim zakovnim trnom in ugrezno glavo -AlA/St (ISO 15978:2002)Offene Blindniete mit Sollbruchdorn und Senkkopf - AIA/St (ISO 15978:2002)Rivets aveugles a rupture de tige a corps ouvert, a tete fraisée - AIA/St (ISO 15978:2002)Open end blind rivets with break pull mandrel and countersunk head - AIA/St (ISO 15978:2002)21.060.40KoviceRivetsICS:Ta slovenski standard je istoveten z:EN ISO 15978:2002SIST EN ISO 15978:2003en01-julij-2003SIST EN ISO 15978:2003SLOVENSKISTANDARD
SIST EN ISO 15978:2003
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 15978November 2002ICS 21.060.40English versionOpen end blind rivets with break pull mandrel and countersunkhead - AIA/St (ISO 15978:2002)Rivets aveugles à rupture de tige à corps ouvert, à têtefraisée - AIA/St (ISO 15978:2002)Offene Blindniete mit Sollbruchdorn und Senkkopf - AIA/St(ISO 15978:2002)This European Standard was approved by CEN on 14 October 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 15978:2002 ESIST EN ISO 15978:2003EN ISO 15978:2002 (E)2CORRECTED
2002-12-18ForewordThis document (EN ISO 15978:2002) has been prepared by Technical Committee ISO/TC 2"Fasteners" in collaboration with Technical Committee CEN/TC 185 "Threaded and non-threaded mechanical fasteners and accessories", the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication ofan identical text or by endorsement, at the latest by May 2003, and conflicting national standardsshall be withdrawn at the latest by May 2003.According to the CEN/CENELEC Internal Regulations, the national standards organizations ofthe following countries are bound to implement this European Standard: Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.Endorsement noticeThe text of ISO 15978:2002 has been approved by CEN as EN ISO 15978:2002 without anymodifications.NOTE
Normative references to International Standards are listed in Annex ZA (normative).SIST EN ISO 15978:2003
EN ISO 15978:2002 (E)3Annex ZA(normative)Normative references to international publicationswith their relevant European publicationsThis European Standard incorporates by dated or undated reference, provisions from otherpublications. These normative references are cited at the appropriate places in the text and thepublications are listed hereafter. For dated references, subsequent amendments to or revisions ofany of these publications apply to this European Standard only when incorporated in it byamendment or revision. For undated references the latest edition of the publication referred toapplies (including amendments).NOTE Where an International Publication has been modified by common modifications, indicatedby (mod.), the relevant EN/HD applies.PublicationYearTitleENYearISO 32692000Fasteners - AcceptanceinspectionEN ISO 32692000ISO 145882000Blind rivets - Terminology anddefinitionsEN ISO 145882000ISO 145892000Blind rivets - Mechanical testingEN ISO 145892000SIST EN ISO 15978:2003SIST EN ISO 15978:2003
Reference numberISO 15978:2002(E)© ISO 2002
INTERNATIONAL STANDARD ISO15978First edition2002-11-01Open end blind rivets with break pull mandrel and countersunk head — AIA/St Rivets aveugles à rupture de tige à corps ouvert, à tête fraisée — AIA/StSIST EN ISO 15978:2003
ISO 15978:2002(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
ISO 2002 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
www.iso.ch Printed in Switzerland
ii © ISO 2002 – All rights reserved
SIST EN ISO 15978:2003
ISO 15978:2002(E) © ISO 2002 – All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the su...