EN ISO 15975:2002

Closed end blind rivets with break pull mandrel and protrudiing head - AI/AIA (ISO 15975:2002)

ISO 15975 specifies dimensional and mechanical characteristics and application data for closed end blind rivets with break pull mandrel and protruding head, with a commercially pure aluminium body (Al) and an aluminium alloy mandrel (AlA) and with nominal diameters from 3,2 mm up to and including 4,8 mm.

Geschlossene Blindniete mit Sollbruchdorn und Flachkopf - AI/AIA (ISO 15975:2002)

Diese Internationale Norm legt Maße und mechanische Eigenschaften sowie Anwendungsdaten für geschlossene Blindniete mit Sollbruchdorn und Flachkopf, mit einer Niethülse aus handelsüblich reinem Aluminium (Al) und einem Nietdorn aus Aluminiumlegierung (AlA) und mit Nenndurchmessern, d, von 3,2 mm bis 4,8 mm fest.

Rivets aveugles à rupture de tige à corps fermé, à tête bombée - AI/AIA (ISO 15975:2002)

L'ISO 15975:2002 spécifie les caractéristiques dimensionnelles et mécaniques ainsi que les données d'application pour les rivets aveugles à rupture de tige à corps fermé, à tête bombée, avec un corps en pur aluminium commercial (Al) et une tige en alliage d'aluminium (AlA), de diamètre nominal compris entre 3,2 mm et 4,8 mm inclus.

Slepe polne kovice z zarezanim zakovnim trnom in zaobljeno valjasto glavo - Al/AlA (ISO 15975:2002)

General Information

• Status: Published
• Publication Date: 31-Oct-2002
• ICS: 21.060.40 - Rivets
• Technical Committee: CEN/TC 185 - Threaded and nonthreaded mechanical fasteners and accessories
• Drafting Committee: CEN/TC 185 - Threaded and nonthreaded mechanical fasteners and accessories
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Start Date: 04-Feb-2008
• Completion Date: 04-Feb-2008
• Ref Project: SIST EN ISO 15975:2003 - Closed end blind rivets with break pull mandrel and protrudiing head - AI/AIA (ISO 15975:2002)

Standards Content (Sample)

SLOVENSKI STANDARD
01-julij-2003
Slepe polne kovice z zarezanim zakovnim trnom in zaobljeno valjasto glavo -
Al/AlA (ISO 15975:2002)
Closed end blind rivets with break pull mandrel and protrudiing head - AI/AIA (ISO
15975:2002)
Geschlossene Blindniete mit Sollbruchdorn und Flachkopf - AI/AIA (ISO 15975:2002)
Rivets aveugles a rupture de tige a corps fermé, a tete bombée - AI/AIA (ISO
15975:2002)
Ta slovenski standard je istoveten z: EN ISO 15975:2002
ICS:
21.060.40 Kovice Rivets
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 15975
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2002
ICS 21.060.40
English version
Closed end blind rivets with break pull mandrel and protrudiing
head - AI/AIA (ISO 15975:2002)
Rivets aveugles à rupture de tige à corps fermé, à tête Geschlossene Blindniete mit Sollbruchdorn und Flachkopf -
bombée - AI/AIA (ISO 15975:2002) AI/AIA (ISO 15975:2002)
This European Standard was approved by CEN on 14 October 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15975:2002 E
worldwide for CEN national Members.

CORRECTED  2002-12-18
Foreword
This document (EN ISO 15975:2002) has been prepared by Technical Committee ISO/TC 2
"Fasteners" in collaboration with Technical Committee CEN/TC 185 "Threaded and non-
threaded mechanical fasteners and accessories", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by May 2003, and conflicting national standards
shall be withdrawn at the latest by May 2003.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,
Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 15975:2002 has been approved by CEN as EN ISO 15975:2002 without any
modifications.
NOTE Normative references to International Standards are listed in Annex ZA (normative).
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 3269 2000 Fasteners - Acceptance EN ISO 3269 2000
inspection
ISO 14588 2000 Blind rivets - Terminology and EN ISO 14588 2000
definitions
ISO 14589 2000 Blind rivets - Mechanical testing EN ISO 14589 2000
INTERNATIONAL ISO
STANDARD 15975
First edition
2002-11-01
Closed end blind rivets with break pull
mandrel and protruding head — AI/AIA
Rivets aveugles à rupture de tige à corps fermé, à tête bombée — AI/AIA

Reference number
ISO 15975:2002(E)
©
ISO 2002
ISO 15975:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.ch
Printed in Switzerland
ii © ISO 2002 – All rights reserved

ISO 15975:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. Intern
...