iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1736:2000

(Main)

Refrigerating systems and heat pumps - Flexible pipe elements, vibration isolators and expansion joints - Requirements, design and installation

Refrigerating systems and heat pumps - Flexible pipe elements, vibration isolators and expansion joints - Requirements, design and installation

This European Standard describes requirements, design and installation of flexible pipe elements (e.g. metallic flexible pipe, metallic flexible tube, non-metallic flexible tube, expansion joint) used in the refrigerant circuits of refrigerating systems and heat pumps. It does not apply to flexible pipes that are only occasionally stressed beyond the elastic limit, e.g. during repair work, or to joints which are free to rotate or hinge.

Kälteanlagen und Wärmepumpen - Flexible Rohrleitungsteile, Schwingungsabsorber und Kompensatoren - Anforderungen, Konstruktion und Einbau

Diese Europäische Norm gilt für flexible Rohrleitungsteile (z.B. biegsames Metall-Rohr, Metall-Schlauch, Nichtmetall-Schlauch, Schwingungsabsorber, Kom- pensator) in Kältemittelkreisläufen von Kälteanlagen und Wärmepumpen. Sie gilt nicht für biegsame Rohre, die nur gelegentlich über ihre Elastizitäts- grenze hinaus beansprucht werden, z.B. bei Reparaturen, oder für drehbar gelagerte Verbindungen oder Rohrgelenke.

Systèmes de réfrigération et pompes à chaleur - Eléments flexibles de tuyauterie, isolateurs de vibration et joints de dilatation - Exigences, conception et installation

La présente norme européenne décrit les exigences, la conception et l'installation des éléments flexibles de tuyauteries (par exemple tuyauterie flexible métallique, tuyau flexible métallique, tuyau flexible non métallique, joint d'expansion) utilisés dans les circuits de fluides frigorigènes des systèmes de réfrigération et pompes à chaleur. Elle ne s'applique pas aux tuyauteries flexibles qui ne subissent qu'occasionnellement des contraintes au-delà de la limite d'élasticité, comme par exemple, lors de travaux de réparation, ou aux raccords qui tournent ou pivotent librement.

Refrigerating systems and heat pumps - Flexible pipe elements, vibration isolators and expansion joints - Requirements, design and installation

General Information

Status
Withdrawn
Publication Date
18-Jan-2000
Withdrawal Date
11-Nov-2008
ICS
27.080 - Heat pumps
27.200 - Refrigerating technology
Technical Committee
CEN/TC 182 - Refrigerating systems, safety and environmental requirements
Drafting Committee
CEN/TC 182/WG 2 - Design and testing
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
12-Nov-2008
Completion Date
12-Nov-2008
Ref Project
SIST EN 1736:2000 - Refrigerating systems and heat pumps - Flexible pipe elements, vibration isolators and expansion joints - Requirements, design and installation

Relations

Replaced By
EN 1736:2008 - Refrigerating systems and heat pumps - Flexible pipe elements, vibration isolators, expansion joints and non-metallic tubes - Requirements, design and installation
Effective Date
22-Dec-2008

Buy Standard

EN 1736:2000EN 1736:2000
PreviousNext
Standard
EN 1736:2000
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Refrigerating systems and heat pumps - Flexible pipe elements, vibration isolators and expansion joints - Requirements, design and installationKälteanlagen und Wärmepumpen - Flexible Rohrleitungsteile, Schwingungsabsorber und Kompensatoren - Anforderungen, Konstruktion und EinbauSystemes de réfrigération et pompes a chaleur - Eléments flexibles de tuyauterie, isolateurs de vibration et joints de dilatation - Exigences, conception et installationRefrigerating systems and heat pum
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 22712:2023(Main)
Refrigerating systems and heat pumps - Competence of personnel (ISO 22712:2023)
SIST EN ISO 22712:2023

This document defines the activities related to refrigerating systems according to ISO 5149‑1, ISO 5149‑2, ISO 5149‑3 and ISO 5149‑4 and other equivalent standards, such as EN 378‑1, EN 378‑2, EN 378‑3, EN 378‑4 and the associated competence profiles. It also establishes the competence criteria for persons who carry out these activities. Activities concerning electricity are excluded.
NOTE 1   As a refrigerating circuit is considered not to incorporate electrical and electronic systems, activities in this area are not part of this document. National regulations or appropriate International or national standards can be referred to for competence on electrical and electronic systems.
NOTE 2   This document does not apply to persons carrying out work on self‑contained refrigerating systems as defined in ISO 5149‑1 or EN 378‑1, from the initial design of the product to the complete manufacture of the product, provided the process is controlled and the methods used are checked by an organization or individual responsible for the conformance with statutory requirements on health, safety and environment (e.g. energy efficiency).
NOTE 3   This document does not constitute a training programme.

  • Standard
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21922:2021(Main)
Refrigerating systems and heat pumps - Valves - Requirements, testing and marking (ISO 21922:2021)
SIST EN ISO 21922:2022

This document specifies safety requirements, certain functional requirements, and marking of valves and other components with similar bodies, hereinafter called valves, for use in refrigerating systems including heat pumps.
This document includes requirements for valves with extension pipes.
This document describes the procedure to be followed when designing valve parts subjected to pressure as well as the criteria to be used in the selection of materials.
This document describes methods by which reduced impact values at low temperatures may be taken into account in a safe manner.
This document applies to the design of bodies and bonnets for pressure relief devices, including bursting disc devices, with respect to pressure containment but it does not apply to any other aspects of the design or application of pressure relief devices.
In addition, this document is applicable to valves with a maximum operating temperature not exceeding 200 °C and a maximum allowable pressure not exceeding 160 bar[1].
[1] 1 bar = 0,1 MPa.

  • Standard
    100 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    96 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 378-3:2016+A1:2020(Main + Amendment)
Refrigerating systems and heat pumps - Safety and environmental requirements - Part 3: Installation site and personal protection
SIST EN 378-3:2017+A1:2021

This European Standard specifies the requirements for the safety of persons and property, provides guidance for the protection of the environment and establishes procedures for the operation, maintenance and repair of refrigerating systems and the recovery of refrigerants.
The term “refrigerating system” used in this European Standard includes heat pumps.
This Part 3 of the European Standard is applicable to the installation site (plant space and services). It specifies requirements on the site for safety, which may be needed because of, but not directly connected with, the refrigerating system and its ancillary components.
This standard applies:
a)   to refrigerating systems, stationary or mobile, of all sizes except to vehicle air conditioning systems covered by a specific product standard e.g. ISO 13043;
b)   to secondary cooling or heating systems;
c)   to the location of the refrigerating systems;
d)   to replaced parts and added components after adoption of this standard if they are not identical in function and in the capacity.
Systems using refrigerants other than those listed in of !EN 378 1:2016+A1:2020", Annex E are not covered by this standard.
This standard does not apply to goods in storage.
This standard is not applicable to refrigerating systems which were manufactured before the date of its publication as a European Standard except for extensions and modifications to the system which were implemented after publication.
This standard is applicable to new refrigerating systems, extensions or modifications of already existing systems, and for existing stationary systems, being transferred to and operated on another site.
This standard also applies in the case of the conversion of a system for another refrigerant type, in which case conformity with the relevant clauses of parts 1 to 4 of the standard shall be assessed.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 378-1:2016+A1:2020(Main + Amendment)
Refrigerating systems and heat pumps - Safety and environmental requirements - Part 1: Basic requirements, definitions, classification and selection criteria
SIST EN 378-1:2017+A1:2021

This European Standard specifies the requirements for the safety of persons and property, provides guidance for the protection of the environment and establishes procedures for the operation, maintenance and repair of refrigerating systems and the recovery of refrigerants.
The term “refrigerating system” used in this European Standard includes heat pumps.
This part of EN 378 specifies the classification and selection criteria applicable to refrigerating systems. These classification and selection criteria are used in parts 2, 3 and 4.
This standard applies:
a)   to refrigerating systems, stationary or mobile, of all sizes except to vehicle air conditioning systems covered by a specific product standard e.g. ISO 13043;
b)   to secondary cooling or heating systems;
c)   to the location of the refrigerating systems;
d)   to replaced parts and added components after adoption of this standard if they are not identical in function and in the capacity;
Systems using refrigerants other than those listed in Annex E of this European Standard are not covered by this standard.
Annex C specifies how to determine the amount of refrigerant permitted in a given space, which when exceeded, requires additional protective measures to reduce the risk.
Annex E specifies criteria for safety and environmental considerations of different refrigerants used in refrigeration and air conditioning.
This standard is not applicable to refrigerating systems and heat pumps which were manufactured before the date of its publication as a European Standard except for extensions and modifications to the system which were implemented after publication.
This standard is applicable to new refrigerating systems, extensions or modifications of already existing systems, and for existing stationary systems, being transferred to and operated on another site.
This standard also applies in the case of the conversion of a system to another refrigerant type, in which case conformity to the relevant clauses of parts 1 to 4 of the standard shall be assessed.
Product family standards dealing with the safety of refrigerating systems takes precedence over horizontal and generic standards covering the same subject.

  • Standard
    76 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14276-1:2020(Main)
Pressure equipment for refrigerating systems and heat pumps - Part 1: Vessels - General requirements
SIST EN 14276-1:2020

This document specifies the requirements for material, design, manufacturing, testing and documentation for stationary pressure vessels intended for use in refrigerating systems and heat pumps. These systems are referenced in this document as refrigerating systems as defined in EN 378-1:2016.
The term "refrigerating system" used in this document includes heat pumps.
This document applies to vessels, including welded or brazed attachments up to and including the nozzle flanges, screwed, welded or brazed connectors, or to the edge to be welded or brazed at the first circumferential joint connecting piping or other elements.
This document applies to pressure vessels with an internal pressure down to -1 bar, to account for the evacuation of the vessel prior to charging with refrigerant.
This document applies to both the mechanical loading conditions and thermal conditions as defined in EN 13445-3:2014  associated with refrigerating systems. It applies to pressure vessels subject to the maximum allowable temperatures for which nominal design stresses for materials are derived using EN 13445-2:2014  and EN 13445-3:20141 or as specified in this document. In addition, vessels designed to this document can have a maximum allowable temperature not exceeding 200 °C and a maximum design pressure not exceeding 160 bar. Outside of these limits, it is important that the EN 13445 series be used for the design, construction and inspection of the vessel. Under these circumstances, it is important that the unique nature of refrigerating plant, as indicated in the introduction to this document, also be taken into account.
It is important that pressure vessels used in refrigerating systems and heat pumps of category less than II as defined in Annex H comply with other relevant clauses of EN 378-2:2016 for vessels.
This document applies to pressure vessels where the main pressure bearing parts are manufactured from metallic ductile materials as defined in Clause 4 and Annex I of this document.
This document does not apply to vessels of the following types:
-   vessels of riveted construction;
-   multi-layered, autofrettaged or prestressed vessels;
-   vessels directly heated by a flame;
-   "roll bond" heat exchangers.

  • Standard
    106 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    88 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14276-2:2020(Main)
Pressure equipment for refrigerating systems and heat pumps - Part 2: Piping - General requirements
SIST EN 14276-2:2020

1.1   This document specifies the requirements for material, design, manufacturing, testing and documentation for stationary piping intended for use in refrigerating systems, heat pumps and secondary cooling and heating systems. These refrigerating systems and heat pump systems are referenced in this document as refrigerating systems as defined in EN 378-1:2016.
The term "refrigerating system" used in this document includes heat pumps.
1.2   This document applies to piping, including welded or brazed attachments up to and including the flanges, screwed, welded or brazed connectors, or to the edge to be welded or brazed at the first circumferential joint connecting piping or other elements.
1.3   This document applies to the selection, application and installation of safety accessories intended to protect the piping during the various phases of the refrigeration cycle.
1.4   This document applies to the following piping:
-   heat exchanger consisting of piping for the purpose of cooling or heating air where piping aspects are predominant;
-   piping incorporated into an assembly (e.g. self-contained system, condensing unit);
-   field erected piping.
1.5   This document applies to piping with an internal pressure down to -1 bar, to account for the evacuation of the piping prior to charging with refrigerant.
1.6   This document applies to both the mechanical loading conditions and thermal conditions as defined in EN 13445 3:2014/A5:2018 associated with refrigerating systems. It applies to piping subject to the maximum allowable temperatures for which nominal design stresses for materials are derived using EN 14276-1:2020 or as specified in this document. In addition, piping designed to this document will have a maximum design temperature not exceeding 200 °C and a maximum design pressure not exceeding 160 bar. Outside of these limits, the EN 13480 series can be used for the design construction and inspection of the piping. Under these circumstances, the unique nature of a refrigerating plant, as indicated in the introduction of EN 14276-1:2020, will also be taken into account.
1.7   This document applies to piping where the main pressure bearing parts are manufactured from metallic ductile materials as defined in Clause 4 and in EN 14276-1:2020.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 378-4:2016+A1:2019(Main + Amendment)
Refrigerating systems and heat pumps - Safety and environmental requirements - Part 4: Operation, maintenance, repair and recovery
SIST EN 378-4:2017+A1:2019

This European Standard specifies the requirements for the safety of persons and property, provides guidance for the protection of the environment and establishes procedures for the operation, maintenance and repair of refrigerating systems and the recovery of refrigerants.
The term "refrigerating system" used in this European Standard includes heat pumps.
This standard applies:
a)   to refrigerating systems, stationary or mobile, of all sizes including heat pumps;
b)   to secondary cooling or heating systems;
c)   to the location of the refrigerating systems;
d)   to parts replaced and components added after adoption of this standard if they are not identical in function and capacity.
This standard does not cover "motor vehicle air conditioners" constructed according to product standards such as ISO 13043.
Systems using refrigerants other than those listed in FprEN 378-1:2016, Annex E are not covered by this standard unless they have been assigned to a safety class according to ISO 817.
This standard does not apply to goods in storage.
This standard is not applicable to refrigeration systems and heat pumps which were manufactured before the date of its publication as a European Standard except for extensions and modifications to the system which were implemented after publication.
This standard is applicable to new refrigerating systems, extensions or modifications of already existing systems, and for existing stationary systems, being transferred to and operated on another site.
This standard also applies in the case of the conversion of a system to another refrigerant type, in which case conformity to the relevant clauses of parts 1 to 4 of the standard shall be assessed.
This Part 4 of the European Standard specifies requirements for safety and environmental aspects in relation to operation, maintenance, and repair of refrigerating systems and the recovery, reuse and disposal of all types of refrigerant, refrigerant oil, heat-transfer fluid, refrigerating system and part thereof.
These requirements are intended to minimise risks of injury to persons and damage to property and the environment resulting from improper handling of the refrigerants or from contaminants leading to system breakdown and resultant emission of the refrigerant.
Subclauses 4, 5.1.1 to 5.1.4, 5.2, 5.3.1, 5.3.3 and 6.6 of this European Standard are not applicable to unitary systems having a power cord, being factory sealed, and in conformance with EN 60335 series.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13136:2013+A1:2018(Main + Amendment)
Refrigerating systems and heat pumps - Pressure relief devices and their associated piping - Methods for calculation
SIST EN 13136:2014+A1:2019

1.1   This European Standard describes the calculation of mass flow for sizing pressure relief devices for components of refrigerating systems.
NOTE   The term "refrigerating system" used in this European Standard includes heat pumps.
1.2   This European Standard describes the calculation of discharge capacities for pressure relief valves and other pressure relief devices in refrigerating systems including the necessary data for sizing these when relieving to atmosphere or to components within the system at lower pressure.
1.3   This European Standard specifies the requirements for selection of pressure relief devices to prevent excessive pressure due to internal and external heat sources, the sources of increasing pressure (e.g. compressor, heaters, etc.) and thermal expansion of trapped liquid.
1.4   This European Standard describes the calculation of the pressure loss in the upstream and downstream line of pressure relief valves and other pressure relief devices and includes the necessary data.
1.5   This European Standard refers to other relevant standards in Clause 5.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14903:2017(Main)
Refrigerating systems and heat pumps - Qualification of tightness of components and joints (ISO 14903:2017)
SIST EN ISO 14903:2017

ISO 14903:2017 provides the qualification procedure for type approval of the tightness of hermetically sealed and closed components, joints and parts used in refrigerating systems and heat pumps as described in relevant parts of ISO 5149. The sealed and closed components, joints and parts concerned are, in particular, fittings, bursting discs, flanged or fitted assemblies. The tightness of flexible piping made from non-metallic materials is dealt with in ISO 13971. Metal flexible piping are covered by this document.
The requirements contained in this document are applicable to joints of maximum DN 50 and components of internal volume of maximum 5 l and maximum weight of 50 kg.
ISO 14903:2017 is intended to characterize their tightness stresses met during their operations, following the fitting procedure specified by the manufacturer, and to specify the minimal list of necessary information to be provided by the supplier of a component to the person in charge of carrying out this procedure.
It specifies the level of tightness of the component, as a whole, and its assembly as specified by its manufacturer.
It applies to the hermetically sealed and closed components, joints and parts used in the refrigerating installations, including those with seals, whatever their material and their design are.
ISO 14903:2017 specifies additional requirements for mechanical joints that can be recognized as hermetically sealed joints.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 378-2:2016(Main)
Refrigerating systems and heat pumps - Safety and environmental requirements - Part 2: Design, construction, testing, marking and documentation
SIST EN 378-2:2017

This European Standard specifies the requirements for the safety of persons and property, provides guidance for the protection of the environment and establishes procedures for the operation, maintenance and repair of refrigerating systems and the recovery of refrigerants.
The term "refrigerating system" used in this European Standard includes heat pumps.
This Part 2 of this Standard is applicable to the design, construction and installation of refrigerating systems including piping, components and materials. It includes ancillary equipment not covered in FprEN 378-1:2016, FprEN 378-3:2016 or FprEN 378-4:2016 which is directly associated with these systems. It also specifies requirements for testing, commissioning, marking and documentation. Requirements for secondary heat transfer circuits are excluded except for any protection requirements associated with the refrigerating system. Ancillary equipment includes, for example, fans, fan motors, electrical motors and transmission assemblies for open compressor systems.
This standard applies:
a)   to refrigerating systems, stationary or mobile, of all sizes except to vehicle air conditioning systems covered by a specific product standard, e.g. ISO 13043;
b)   to secondary cooling or heating systems;
c)   to the location of the refrigerating systems;
d)   to replaced parts and added components after adoption of this standard if they are not identical in function and in the capacity.
Systems using refrigerants other than those listed in Annex E of FprEN-378 1:2016 are not covered by this standard.
This standard does not apply to goods in storage.
This standard is not applicable to refrigerating systems which were manufactured before the date of its publication as a European Standard except for extensions and modifications to the system which were implemented after publication.
This standard is applicable to new refrigerating systems, extensions or modifications of already existing systems, and for existing stationary systems, being transferred to and operated on another site.
This standard also applies in the case of the conversion of a system to another refrigerant type, in which case conformity to the relevant clauses of parts 1 to 4 of the standard shall be assessed.

  • Standard
    86 pages
    English language
    sale 10% off
    e-Library read for
    1 day