EN ISO 13628-1:2005

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 1: General requirements and recommendations (ISO 13628-1:2005)

ISO 13628-1:2005 provides general requirements and overall recommendations for development of complete subsea production systems, from the design phase to decommissioning and abandonment. ISO 13628-1:2005 is intended as an umbrella document to govern other parts of ISO 13628 dealing with more detailed requirements for the subsystems which typically form part of a subsea production system. However, in some areas (e.g. system design, structures, manifolds, lifting devices, and colour and marking) more detailed requirements are included herein, as these subjects are not covered in a subsystem standard.
The complete subsea production system comprises several subsystems necessary to produce hydrocarbons from one or more subsea wells and transfer them to a given processing facility located offshore (fixed, floating or subsea) or onshore, or to inject water/gas through subsea wells. ISO 13628-1:2005 and its related subsystem standards apply as far as the interface limits described in Clause 4.
Specialized equipment, such as split trees and trees and manifolds in atmospheric chambers, are not specifically discussed because of their limited use. However, the information presented is applicable to those types of equipment.

Erdöl- und Erdgasindustrie - Auslegung und Betrieb von Unterwasser-Produktionssystemen - Teil 1: Allgemeine Anforderungen und Empfehlungen (ISO 13628-1:2005)

Industries du pétrole et du gaz naturel - Conception et exploitation des systèmes de production immergés - Partie 1: Exigences générales et recommandations (ISO 13628-1:2005)

L'ISO 13628-1:2005 fournit des exigences générales et des recommandations pour le développement de systèmes de production immergés complets, de la phase de conception jusqu'au démantèlement et à l'abandon. L'ISO 13628-1:2005 est un document cadre régissant les autres parties de l'ISO 13628 qui traitent de manière plus détaillée des exigences relatives aux sous-systèmes faisant généralement partie d'un système de production immergé. Néanmoins, dans certains domaines (par exemple, conception du système, structures, manifolds, dispositifs de levage, couleur et marquage), des exigences plus détaillées sont incluses dans la présente norme, car ces sujets ne sont pas couverts par une norme de sous-système. Le système de production immergé complet comprend plusieurs sous-systèmes nécessaires pour produire des hydrocarbures à partir d'un ou plusieurs puits sous-marins et les transférer vers une installation de traitement donnée située en mer (fixe, flottante ou immergée) ou à terre, ou pour injecter de l'eau/du gaz dans les puits sous-marins. L'ISO 13628-1:2005 et les normes de sous-systèmes connexes, s'appliquent jusqu'aux limites d'interface décrites à l'Article 4. Les équipements spéciaux, tels que les «split trees», les têtes de production et les manifolds des chambres atmosphériques, ne sont pas spécifiquement décrits du fait de leur usage limité. Toutefois, les informations fournies sont applicables à ces types d'équipement.

Industrija za predelavo nafte in zemeljskega plina – Načrtovanje in upravljanje proizvodnje v podmorskih sistemih – 1. del: Splošne zahteve in priporočila (ISO 13628-1:2005)

General Information

• Status: Published
• Publication Date: 14-Nov-2005
• Withdrawal Date: 30-May-2006
• ICS: 75.180.10 - Exploratory, drilling and extraction equipment
• Technical Committee: CEN/TC 12 - Materials, equipment and offshore structures for petroleum and natural gas industries
• Drafting Committee: CEN/TC 12 - Materials, equipment and offshore structures for petroleum and natural gas industries
• Current Stage: 9092 - Decision on results of review/2YR ENQ - revise - Review Enquiry
• Start Date: 09-Apr-2009
• Completion Date: 09-Apr-2009
• Ref Project: SIST EN ISO 13628-1:2006 - Petroleum and natural gas industries - Design and operation of subsea production systems - Part 1: General requirements and recommendations (ISO 13628-1:2005)

Relations

• Replaces: EN ISO 13628-1:1999 - Petroleum and natural gas industries - Design and operation of subsea production systems - Part 1: General requirements and recommendations (ISO 13628-1:1999)
• Effective Date: 22-Dec-2008
• Amended By: EN ISO 13628-1:2005/A1:2010 - Petroleum and natural gas industries - Design and operation of subsea production systems - Part 1: General requirements and recommendations - Amendment 1: Revised Clause 6 (ISO 13628-1:2005/Amd 1:2010)
• Effective Date: 22-Dec-2008
• Amended By: EN ISO 13628-1:2005/prA2 - Petroleum and natural gas industries - Design and operation of subsea production systems - Part 1: General requirements and recommendations - Amendment 2: Revised Annex L (ISO 13628-1:2005/DAM 2:2008)
• Effective Date: 22-Dec-2008
• Revised: prEN ISO 13628-1 - Oil and gas industries including low carbon energy - Design and operation of subsea production systems - Part 1: General requirements and recommendations (ISO/DIS 13628-1:2023)
• Effective Date: 11-Oct-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-september-2006
,QGXVWULMD]DSUHGHODYRQDIWHLQ]HPHOMVNHJDSOLQD±1DþUWRYDQMHLQXSUDYOMDQMH
SURL]YRGQMHYSRGPRUVNLKVLVWHPLK±GHO6SORãQH]DKWHYHLQSULSRURþLOD,62

Petroleum and natural gas industries - Design and operation of subsea production
systems - Part 1: General requirements and recommendations (ISO 13628-1:2005)
Erdöl- und Erdgasindustrie - Auslegung und Betrieb von Unterwasser-
Produktionssystemen - Teil 1: Allgemeine Anforderungen und Empfehlungen (ISO 13628
-1:2005)
Industries du pétrole et du gaz naturel - Conception et exploitation des systemes de
production immergés - Partie 1: Exigences générales et recommandations (ISO 13628-
1:2005)
Ta slovenski standard je istoveten z: EN ISO 13628-1:2005
ICS:
75.180.10 Oprema za raziskovanje in Exploratory and extraction
odkopavanje equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 13628-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2005
ICS 75.180.10 Supersedes EN ISO 13628-1:1999
English Version
Petroleum and natural gas industries - Design and operation of
subsea production systems - Part 1: General requirements and
recommendations (ISO 13628-1:2005)
Industries du pétrole et du gaz naturel - Conception et Erdöl- und Erdgasindustrien - Konstruktion und Betrieb von
exploitation des systèmes de production immergés - Partie Unterwasser-Produktionssystemen - Teil 1: Allgemeine
1: Exigences générales et recommandations (ISO 13628- Anforderungen und Empfehlungen (ISO 13628-1:2005)
1:2005)
This European Standard was approved by CEN on 21 October 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13628-1:2005: E
worldwide for CEN national Members.

Foreword
This document (EN ISO 13628-1:2005) has been prepared by Technical Committee ISO/TC 67
"Materials, equipment and offshore structures for petroleum and natural gas industries" in
collaboration with Technical Committee CEN/TC 12 "Materials, equipment and offshore
structures for petroleum, petrochemical and natural gas industries", the secretariat of which is
held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by May 2006, and conflicting national standards
shall be withdrawn at the latest by May 2006.

This document supersedes EN ISO 13628-1:1999.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Endorsement notice
The text of ISO 13628-1:2005 has been approved by CEN as EN ISO 13628-1:2005 without any
modifications.
INTERNATIONAL ISO
STANDARD 13628-1
Second edition
2005-11-15
Petroleum and natural gas industries —
Design and operation of subsea
production systems —
Part 1:
General requirements and
recommendations
Industries du pétrole et du gaz naturel — Conception et exploitation des
systèmes de production immergés —
Partie 1: Exigences générales et recommandations

Reference number
ISO 13628-1:2005(E)
©
ISO 2005
ISO 13628-1:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2005 – All rights reserved

ISO 13628-1:2005(E)
Contents Page
Foreword. v
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and abbreviations. 2
3.1 Terms and definitions. 2
3.2 Abbreviated terms . 3
4 Systems and interface descriptions . 6
4.1 General. 6
4.2 System description. 7
4.3 Subsystem interfaces. 9
5 Design . 9
5.1 General. 9
5.2 Design criteria . 9
5.3 Field development . 13
5.4 Design loads. 14
5.5 System design. 14
5.6 Subsea wellhead. 17
5.7 Tubing hanger/tree system. 21
5.8 Completion/workover riser system. 24
5.9 Mudline casing suspension system . 24
5.10 Production controls. 25
5.11 Flowlines and end connections . 26
5.12 Template and manifold systems . 34
5.13 Production risers . 40
5.14 ROV/ROT intervention systems . 41
5.15 Colours and marking. 41
6 Materials and corrosion protection. 42
6.1 Material evaluation. 42
6.2 Metallic materials. 42
6.3 Non-metallic materials. 44
6.4 Bolting materials for subsea applications .45
6.5 External corrosion protection . 46
6.6 Design limitations for materials . 46
7 Manufacturing and testing. 48
7.1 General requirements and recommendations . 48
7.2 Test procedures . 48
7.3 Integration testing. 49
8 Operations . 50
8.1 General. 50
8.2 Transportation and handling . 50
8.3 Installation . 51
8.4 Drilling and completion. 52
8.5 Hook-up and commissioning . 53
8.6 Well intervention. 58
8.7 Maintenance . 59
8.8 Decommissioning. 61
ISO 13628-1:2005(E)
9 Documentation . 62
9.1 General . 62
9.2 Engineering and manufacturing. 62
9.3 Operating and maintenance. 63
9.4 As-built/as-installed documentation . 63
Annex A (informative) Description of subsea production systems . 64
Annex B (normative) Colours and marking . 163
Annex C (informative) Integration testing of subsea production equipment. 170
Annex D (informative) Typical procedures for commissioning .
...