EN ISO 25178-605:2014
(Main)Geometrical product specifications (GPS) - Surface texture: Areal - Part 605: Nominal characteristics of non-contact (point autofocus probe) instruments (ISO 25178-605:2014)
Geometrical product specifications (GPS) - Surface texture: Areal - Part 605: Nominal characteristics of non-contact (point autofocus probe) instruments (ISO 25178-605:2014)
ISO 25178-605:2014 describes the metrological characteristics of a non-contact instrument for measuring surface texture using point autofocus probing.
Geometrische Produktspezifikation (GPS) - Oberflächenbeschaffenheit: Flächenhaft - Teil 605: Merkmale von berührungslos messenden Geräten (Punkt-Autofokus-Sensor) (ISO 25178-605:2014)
Dieser Teil der ISO 25178 legt die messtechnischen Merkmale eines berührungslos messenden Messgeräts zur flächenhaften Messung der Oberflächenbeschaffenheit fest, das einen Punkt-Autofokus-Sensor verwen-det.
Spécification géométrique des produits (GPS) - État de surface: Surfacique - Partie 605: Caractéristiques nominales des instruments sans contact (capteur autofocus à point) (ISO 25178-605:2014)
l'ISO 25178-605:2014 décrit les caractéristiques métrologiques d'un instrument sans contact pour le mesurage de l'état de surface à l'aide d'un capteur autofocus à point.
Specifikacija geometrijskih veličin izdelka (GPS) - Tekstura površine: ploskovna - 605. del: Imenske značilnosti brezkontaktnih (točka avtofokusne sonde) instrumentov (ISO 25178-605:2014)
EN ISO 25178-605 opisuje meroslovne značilnosti brezkontaktnih instrumentov za merjenje teksture površine z avtofokusno sondo.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2014
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND *36 7HNVWXUDSRYUãLQH SORVNRYQD
GHO ,PHQVNH]QDþLOQRVWLEUH]NRQWDNWQLK WRþNDDYWRIRNXVQHVRQGH
LQVWUXPHQWRY ,62
Geometrical product specifications (GPS) - Surface texture: Areal - Part 605: Nominal
characteristics of non-contact (point autofocus probe) instruments (ISO 25178-605:2014)
Geometrische Produktspezifikation (GPS) - Oberflächenbeschaffenheit: Flächenhaft -
Teil 605: Merkmale von berührungslos messenden Geräten (Punkt-Autofokus-Sensor)
(ISO 25178-605:2014)
Spécification géométrique des produits (GPS) - État de surface: Surfacique - Partie 605:
Caractéristiques nominales des instruments sans contact (à capteur autofocus à point)
(ISO 25178-605:2014)
Ta slovenski standard je istoveten z: EN ISO 25178-605:2014
ICS:
17.040.20 Lastnosti površin Properties of surfaces
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 25178-605
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2014
ICS 17.040.20
English Version
Geometrical product specifications (GPS) - Surface texture:
Areal - Part 605: Nominal characteristics of non-contact (point
autofocus probe) instruments (ISO 25178-605:2014)
Spécification géométrique des produits (GPS) - État de Geometrische Produktspezifikation (GPS) -
surface: Surfacique - Partie 605: Caractéristiques Oberflächenbeschaffenheit: Flächenhaft - Teil 605:
nominales des instruments sans contact (capteur autofocus Merkmale von berührungslos messenden Geräten (Punkt-
à point) (ISO 25178-605:2014) Autofokus-Sensor) (ISO 25178-605:2014)
This European Standard was approved by CEN on 13 January 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 25178-605:2014 E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 25178-605:2014) has been prepared by Technical Committee ISO/TC 213
“Dimensional and geometrical product specifications and verification” in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of
which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by July 2014, and conflicting national standards shall be withdrawn at the
latest by July 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 25178-605:2014 has been approved by CEN as EN ISO 25178-605:2014 without any
modification.
INTERNATIONAL ISO
STANDARD 25178-605
First edition
2014-02-01
Geometrical product specifications
(GPS) — Surface texture: Areal —
Part 605:
Nominal characteristics of non-contact
(point autofocus probe) instruments
Spécification géométrique des produits (GPS) — État de surface:
Surfacique —
Partie 605: Caractéristiques nominales des instruments sans contact
(capteur autofocus à point)
Reference number
ISO 25178-605:2014(E)
©
ISO 2014
ISO 25178-605:2014(E)
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
ISO 25178-605:2014(E)
Contents Page
Foreword .iv
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
3.1 Terms and definitions related to all areal surface texture measurement methods . 2
3.2 Terms and definitions related to x- and y-scanning systems . 9
3.3 Terms and definitions related to optical systems .11
3.4 Terms and definitions related to optical properties of workpiece .12
3.5 Terms and definitions specific to point autofocus profiling .13
4 Descriptions of the influence quantities .14
4.1 General .14
4.2 Influence quantities .14
Annex A (informative) General principles .16
Annex B (informative) Spot size and focal shift.20
Annex C (informative) Beam offset direction and maximum acceptable local slope .23
Annex D (informative) Features of an areal surface texture measuring instrument .26
Annex E (informative) Others: Non-measured point (autofocus error) .28
Annex F (informative) Relation to the GPS matrix .29
Bibliography .31
ISO 25178-605:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 213, Dimensional and geometrical product
specifications and verification.
ISO 25178 consists of the following parts, under the general title Geometrical product specifications
(GPS) — Surface texture: Areal:
— Part 1: Indication of surface texture
— Part 2: Terms, definitions and surface texture parameters
— Part 3: Specification operators
— Part 6: Classification of methods for measuring surface texture
— Part 70: Material measures
— Part 71: Software measurement standards
— Part 601: Nominal characteristics of contact (stylus) instruments
— Part 602: Nominal characteristics of non-contact (confocal chromatic probe) instruments
— Part 603: Nominal characteristics of non-contact (phase-shifting interferometric microscopy)
instruments
— Part 604: Nominal characteristics of non-contact (coherence scanning interferometry) instruments
— Part 605: Nominal characteristics of non-contact (point autofocus probe) instruments
— Part 606: Nominal characteristics of non-contact (focus variation) instruments
— Part 701: Calibration and measurement standards for contact (stylus) instruments
The following parts are under preparation:
iv © ISO 2014 – All rights reserved
ISO 25178-605:2014(E)
— Part 72: XML file format x3p
Calibration and measurement standards for non-contact (confocal chromatic probe) instruments and
calibration and measurement standards for non-contact (phase-shifting interferometric microscopy)
instruments are to form the subject of future parts 702 and 703.
A part 600 is planned which is intended to contain provisions common with the other 600-level parts of
ISO 25178. Once it has been submitted as a Final Draft International Standard, those provisions in the
other 600-level parts that are then redundant will be removed from them.
ISO 25178-605:2014(E)
Introduction
This part of ISO 25178 is a Geometrical Product Specification standard and is to be regarded as a General
GPS standard (see ISO/TR 14638). It influences the chain link 5 of the chains of standards on roughness
profile, waviness profile, primary profile, and areal surface texture.
For more detailed information on the relationship of this standard to the GPS matrix model, see Annex G.
The ISO/GPS Masterplan given in ISO/TR 14638 gives an overview of the ISO/GPS system of which
this standard is a part. The fundamental rules of ISO/GPS given in ISO 8015 apply to this standard and
the default decision rules given i
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.