EN 10017:2004

Steel rod for drawing and/or cold rolling - Dimensions and tolerances

This European Standard specifies the dimensions, the tolerances, the nominal cross-section and the nominal mass of steel rod for drawing.
This European Standard concerns round, square, rectangular and hexagonal rod in steel grades specified in European Standard.

Walzdraht aus Stahl zum Ziehen und/oder Kaltwalzen - Maße und Grenzabmaße

Dieses Dokument legt die Maße, Grenzabmaße, Nennquerschnitte und Nennmassen für Walzdraht zum Ziehen fest.
Dieses Dokument gilt für Rund-, Vierkant-, Flach- und Sechskantwalzdraht aus den Stahlsorten nach Europäischen Normen.

Fil machine en acier destiné au tréfilage et/ou laminage à froid - Dimensions et tolérances

La présente Norme européenne spécifie les dimensions, les tolérances, la section nominale et la masse nominale des fils machine en acier destinés au tréfilage.
La présente Norme européenne concerne les fils machine ronds, carrés, rectangulaires, hexagonaux et demi ronds en nuances d'acier non allié spécifiées dans la Norme européenne.

Jeklene palice za vlečenje in/ali hladno valjanje – Mere in tolerance

General Information

• Status: Published
• Publication Date: 19-Oct-2004
• Withdrawal Date: 29-Apr-2005
• ICS: 77.140.65 - Steel wire, wire ropes and link chains
• Technical Committee: ECISS/TC 106 - Wire rod and wires
• Drafting Committee: ECISS/TC 15 - Wire-rod - Qualities, dimensions, tolerances and specific tests
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 03-Dec-2021
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Mandate: M/120 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on structural metallic products and ancillaries
• Ref Project: SIST EN 10017:2004 - Steel rod for drawing and/or cold rolling - Dimensions and tolerances

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 10017:2004
01-december-2004
-HNOHQHSDOLFH]DYOHþHQMHLQDOLKODGQRYDOMDQMH±0HUHLQWROHUDQFH
Steel rod for drawing and/or cold rolling - Dimensions and tolerances
Walzdraht aus Stahl zum Ziehen und/oder Kaltwalzen - Maße und Grenzabmaße
Fil machine en acier destiné au tréfilage et/ou laminage a froid - Dimensions et
tolérances
Ta slovenski standard je istoveten z: EN 10017:2004
ICS:
77.140.65 Jeklene žice, jeklene vrvi in Steel wire, wire ropes and
verige link chains
SIST EN 10017:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 10017:2004

---------------------- Page: 2 ----------------------

SIST EN 10017:2004



EUROPEAN STANDARD
EN 10017

NORME EUROPÉENNE

EUROPÄISCHE NORM
October 2004
ICS 77.140.65 Supersedes EURONORM 17:1970
English version
Steel rod for drawing and/or cold rolling - Dimensions and
tolerances
Fil machine en acier non allié destiné au tréfilage et/ou Walzdraht aus Stahl zum Ziehen und/oder Kaltwalzen -
laminage à froid - Dimensions et tolérances Maße und Grenzabmaße
This European Standard was approved by CEN on 9 July 2004.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.

CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.




EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10017:2004: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 10017:2004
EN 10017:2004 (E)
Contents
Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Terms and definitions.4
4 Information to be supplied by the purchaser .4
4.1 Information to be supplied by the purchaser .4
4.2 Examples .4
5 Nominal sections and nominal mass.5
6 Dimensions and tolerances .6
6.1 Round rod (Fig. 1).6
6.2 Square rod (Fig. 2) .8
6.3 Rectangular rod (Fig. 3).9
6.4 Hexagonal Rod (Fig. 4).12
7 Mass of coils and checks on dimensional tolerances.14
8 Claims .
...