FprEN ISO 8611-2
(Main)Pallets for materials handling - Flat pallets - Part 2: Performance requirements and selection of tests (ISO/FDIS 8611-2:2024)
Pallets for materials handling - Flat pallets - Part 2: Performance requirements and selection of tests (ISO/FDIS 8611-2:2024)
This document specifies the performance requirements to establish nominal loads for new flat pallets.
It also specifies the tests required for new flat pallets in various handling environments and the performance requirements for tests with payloads. This document does not apply to pallets with a fixed superstructure or a rigid, self-supporting container that can be mechanically attached to the pallet and which contributes to the strength of the pallet.
Paletten für den Gütertransport - Flachpaletten - Teil 2: Leistungsanforderungen und Auswahl von Prüfungen (ISO/FDIS 8611‑2:2024)
Palettes pour la manutention - Palettes plates - Partie 2: Exigences de performance et sélection des essais (ISO/FDIS 8611-2:2024)
Le présent document spécifie les exigences de performance permettant d’établir les charges nominales pour des palettes plates neuves.
Il spécifie également les essais nécessaires pour des palettes plates neuves dans diverses conditions de manutention et les exigences de performance pour des essais avec charges utiles. Le présent document ne s’étend pas aux palettes à superstructure fixe ou à conteneur autoportant rigide pouvant être fixés mécaniquement à la palette et contribuant à sa résistance.
Palete za ravnanje z materiali - Ravne palete - 2. del: Zahtevane lastnosti in izbira preskusa (ISO/DIS 8611-2:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2024
Palete za ravnanje z materiali - Ravne palete - 2. del: Zahtevane lastnosti in izbira
preskusa (ISO/DIS 8611-2:2024)
Pallets for materials handling - Flat pallets - Part 2: Performance requirements and
selection of tests (ISO/DIS 8611-2:2024)
Paletten für den Gütertransport - Flachpaletten - Teil 2: Leistungsanforderungen und
Auswahl von Prüfungen (ISO/DIS 8611-2:2024)
Palettes pour la manutention - Palettes plates - Partie 2: Exigences de performance et
sélection des essais (ISO/DIS 8611-2:2024)
Ta slovenski standard je istoveten z: prEN ISO 8611-2
ICS:
55.180.20 Večnamenske palete General purpose pallets
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT INTERNATIONAL STANDARD
ISO/DIS 8611-2
ISO/TC 51 Secretariat: BSI
Voting begins on: Voting terminates on:
2024-01-23 2024-04-16
Pallets for materials handling — Flat pallets —
Part 2:
Performance requirements and selection of tests
Palettes pour la manutention — Palettes plates —
Partie 2: Exigences de performance et sélection des essais
ICS: 55.180.20
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 8611-2:2024(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2024
ISO/DIS 8611-2:2024(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 8611-2
ISO/TC 51 Secretariat: BSI
Voting begins on: Voting terminates on:
Pallets for materials handling — Flat pallets —
Part 2:
Performance requirements and selection of tests
Palettes pour la manutention — Palettes plates —
Partie 2: Exigences de performance et sélection des essais
ICS: 55.180.20
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2024
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 8611-2:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
ISO/DIS 8611-2:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test conditions .2
4.1 General . 2
4.2 Wooden pallets . 3
4.3 Metal pallets . 3
4.4 Plastic pallets . 3
4.5 Paper pallets . 3
4.6 Wood-based composite pallets . 3
5 Number of replicates .4
6 Performance requirements . .4
7 Selection of the tests .7
7.1 Intended use . 7
7.2 Handling of goods with racking and stacking . 8
7.3 Handling of goods with stacking without racking. 8
7.4 Handling of goods without racking or stacking . 8
7.5 Special applications . 8
7.5.1 General . 8
7.5.2 Automatic handling or conveyors . 9
7.5.3 Lifting with slings . 9
7.5.4 Resistance to impact . 9
7.5.5 Friction tests . 9
8 Test load — Nominal load .9
8.1 Strength tests . 9
8.2 Ultimate load, U . . 9
8.3 Stiffness tests . . 9
8.4 Nominal load. 9
9 Duration for static stiffness tests .10
10 Number of impacts for dynamic tests .10
11 Test report .10
Annex A (informative) Plots of typical force versus deformation from pallet tests showing
the deformation of ultimate load, U .11
Bibliography .13
iii
ISO/DIS 8611-2:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 51, Pallets for unit load method of
materials handling, in collaboration with the European Committee for Standardization (CEN) Technical
Committee CEN/TC 261, Packaging, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 8611-2:2021), which has been editorially
revised.
The main changes compared to the previous edition are as follows:
— The performance criteria for the Test 2 have been changed, and as a result, the data in the examples
in the Table 3 has been modified accordingly.
A list of all parts in the ISO 8611 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
ISO/DIS 8611-2:2023(E)
Introduction
The forces to which pallets are exposed during use vary significantly. The test procedures described in
ISO 8611-1 are approximate simulations of pallet use. These tests help the pallet designer to establish
an initial acceptable balance between the cost and the performance of a pallet design. It is intended
that all results of tests performed using this protocol be confirmed and verified using field trials before
publication of performance or the commercial implementation of a new pallet design.
The nominal load, determined
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.