EN ISO 11114-6:2022

Gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 6: Oxygen pressure surge testing (ISO 11114-6:2022)

This document specifies requirements for the test apparatus and test procedure in order to apply oxygen pressure surges consistently to devices being tested for resistance to ignition by adiabatic compression and to materials for oxygen compatibility.

Gasflaschen - Verträglichkeit von Werkstoffen für Gasflaschen und Ventile mit den in Berührung kommenden Gasen - Teil 6: Sauerstoff-Druckstoßprüfung (ISO 11114-6:2022)

Dieses Dokument legt Anforderungen für Prüfgerät und Prüfverfahren fest für das einheitliche Aufbringen von Sauerstoff-Druckstößen auf Einrichtungen, die auf ihre Zündfestigkeit durch adiabati-sche Verdichtung geprüft werden, sowie auf Werkstoffe im Fall der Prüfung auf Sauerstoffverträglichkeit.

Bouteilles à gaz - Compatibilité des matériaux des bouteilles et des robinets avec les contenus gazeux - Partie 6: Essai de compression adiabatique à l’oxygène (ISO 11114-6:2022)

Le présent document spécifie les exigences relatives à l’appareillage et au mode opératoire d’essai afin d’appliquer, de façon homogène, des surpressions d’oxygène aux dispositifs soumis à des essais de résistance à l’inflammation par compression adiabatique, ainsi qu’aux matériaux afin de vérifier leur compatibilité avec l’oxygène.

Plinske jeklenke - Združljivost materialov za ventil in jeklenko s plinom - 6. del: Adiabatni tlačni preskus s kisikom (ISO 11114-6:2022)

Ta dokument določa zahteve za preskusne naprave in preskusni postopek za dosledno uporabo povišanj tlaka kisika pri napravah, pri katerih se preskuša odpornost na adiabatno krčenje, ter materialih za namene preskusa združljivosti s kisikom.

General Information

• Status: Published
• Publication Date: 13-Sep-2022
• ICS: 23.020.35 - Gas cylinders
• Technical Committee: CEN/TC 23 - Transportable gas cylinders
• Drafting Committee: CEN/TC 23/WG 20 - Cylinder design - Fittings
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 14-Sep-2022
• Due Date: 27-Nov-2023
• Completion Date: 14-Sep-2022
• Ref Project: SIST EN ISO 11114-6:2022 - Gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 6: Oxygen pressure surge testing (ISO 11114-6:2022)

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11114-6:2022
01-november-2022
Plinske jeklenke - Združljivost materialov za ventil in jeklenko s plinom - 6. del:
Adiabatni tlačni preskus s kisikom (ISO 11114-6:2022)
Gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 6:
Oxygen pressure surge testing (ISO 11114-6:2022)
Gasflaschen - Verträglichkeit von Werkstoffen für Gasflaschen und Ventile mit den in
Berührung kommenden Gasen - Teil 6: Sauerstoff-Druckstoßprüfung (ISO 11114-6:2022)
Bouteilles à gaz - Compatibilité des matériaux des bouteilles et des robinets avec les
contenus gazeux - Partie 6: Essai de compression adiabatique à l’oxygène (ISO 11114-
6:2022)
Ta slovenski standard je istoveten z: EN ISO 11114-6:2022
ICS:
23.020.35 Plinske jeklenke Gas cylinders
SIST EN ISO 11114-6:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 11114-6:2022

---------------------- Page: 2 ----------------------
SIST EN ISO 11114-6:2022


EN ISO 11114-6
EUROPEAN STANDARD

NORME EUROPÉENNE

September 2022
EUROPÄISCHE NORM
ICS 23.020.35
English Version

Gas cylinders - Compatibility of cylinder and valve
materials with gas contents - Part 6: Oxygen pressure
surge testing (ISO 11114-6:2022)
Bouteilles à gaz - Compatibilité des matériaux des Gasflaschen - Verträglichkeit von Werkstoffen für
bouteilles et des robinets avec les contenus gazeux - Gasflaschen und Ventile mit den in Berührung
Partie 6: Essai de compression adiabatique à l'oxygène kommenden Gasen - Teil 6: Sauerstoff-
(ISO 11114-6:2022) Druckstoßprüfung (ISO 11114-6:2022)
This European Standard was approved by CEN on 20 August 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11114-6:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 11114-6:2022
EN ISO 11114-6:2022 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 11114-6:2022
EN ISO 11114-6:2022 (E)
European foreword
This document (EN ISO 11114-6:2022) has been prepared by Technical Committee ISO/TC 58 "Gas
cylinders" in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2023, and conflicting national standards shall
be withdrawn at the latest by March 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türk
...