EN 2709:2018
(Main)Aerospace series - Aluminium alloy 2024- - T3510 - Bars and sections - 1,2 mm ≤ (a or D) ≤ 150 mm - With peripheral coarse grain control
Aerospace series - Aluminium alloy 2024- - T3510 - Bars and sections - 1,2 mm ≤ (a or D) ≤ 150 mm - With peripheral coarse grain control
This European Standard specifies the requirements relating to:
Aluminium alloy 2024-
T3510
Bars and sections
1,2 mm ≤ (a or D) ≤ 150 mm
With peripheral coarse grain control
for aerospace applications.
Luft- und Raumfahrt - Aluminiumlegierung 2024- - T3510 - Stangen und Profile - 1,2 mm ≤ (a oder D) ≤ 150 mm - Mit Kontrolle der Grobkornrandzone
Série aérospatiale - Alliage d'aluminium 2024- - T3510 - Barres et profilés - 1,2 mm ≤ (a ou D) ≤ 150 mm - Limitation à la zone périphérique à gros grains
La présente Norme européenne spécifie les exigences relatives à :
Alliage d'aluminium 2024-
T3510
Barres et profilés
1,2 mm ≤ (a ou D) ≤ 150 mm
Limitation à la zone périphérique à gros grains
pour applications aérospatiales.
Aeronavtika - Aluminijeva zlitina 2024- - T3510 - Palice in profili - 1,2 mm ≤ (a or D) ≤ 150 mm - S kontrolo debelozrnatega obrobja
Ta evropski standard določa zahteve za:
Aluminijevo zlitino 2024-
T3510
(palice in profili)
1,2 mm ≤ (a ali D) ≤ 150 mm
s kontrolo debelozrnatega obrobja
za uporabo v aeronavtiki.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.49.025.20AluminijAluminiumICS:Ta slovenski standard je istoveten z:EN 2709:2018SIST EN 2709:2019en,fr,de01-januar-2019SIST EN 2709:2019SLOVENSKI
STANDARD
SIST EN 2709:2019
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 2709
November
t r s z ICS
English Version
Aerospace series æ Aluminium alloy
t r t væ æ T u w s r æ Bars and sections æ
sá t mm ≤≤
s w r mm æ With peripheral coarse grain control Série aérospatiale æ Alliage d 5aluminium
t r t væ æ T u w s r æ Barres et profilés æ
sá t mm ≤≤
s w r mm æ Limitation à la zone périphérique à gros grains
Luftæ und Raumfahrt æ Aluminiumlegierung
t r t væ æ T u w s r æ Stangen und Profile æ
sá t mm ≤≤
s w r mm æ Mit Kontrolle der Grobkornrandzone This European Standard was approved by CEN on
s y September
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
9
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
t y r {ã t r s z ESIST EN 2709:2019
EN 2709:2018
2 Contents Page European foreword . 3 Introduction . 4 1 Scope . 5 2 Normative references . 5 3 Terms and definitions . 5 4 Requirements . 5
SIST EN 2709:2019
EN 2709:2018
3 European foreword This document (EN 2709:2018) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2019, and conflicting national standards shall be withdrawn at the latest by May 2019. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 2709:2019
EN 2709:2018
4 Introduction This European Standard is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258. This European Standard has been prepared in accordance with EN 4500-2. SIST EN 2709:2019
EN 2709:2018
5 1 Scope This European Standard specifies the requirements relating to: Aluminium alloy 2024- T3510 Bars a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.