iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 14037-5:2016

(Main)

Free hanging heating and cooling surfaces for water with a temperature below 120°C - Part 5: Open or closed heated ceiling surfaces - Test method for thermal output

Free hanging heating and cooling surfaces for water with a temperature below 120°C - Part 5: Open or closed heated ceiling surfaces - Test method for thermal output

This European Standard describes the test method and the test installation for determining the thermal output of ceiling mounted heating surfaces according to the specifications of prEN 14037-1:2011, 3.3.2, 3.3.3 and 3.3.4.
This part applies to determine thermal output when chilled ceilings according to EN 14240 are also used for heating.
NOTE   Test results according to this part cannot be compared with results according to EN 14037-2 because great discrepancies are given at open ceilings, convective components and heating surfaces without upper insulation.

An der Decke frei abgehängte Heiz- und Kühlflächen für Wasser mit einer Temperatur unter 120 °C - Teil 5: Offene oder geschlossene Deckenheizflächen - Prüfverfahren für die Wärmeleistung

Panneaux rayonnants de chauffage et de rafraîchissement alimentés avec une eau à une température inférieure à 120 °C - Partie 5: Méthode d'essai pour la détermination de la puissance thermique des surfaces de plafond de chauffage ouvertes ou fermées

Prosto viseče grelne in hladilne površine za vodo s temperaturo do 120 °C - 5. del: Odprte ali zaprte stropne grelne površine - Metoda preskušanja toplotne moči

Ta evropski standard opisuje preskusno metodo in preskusno napravo za določevanje toplotne moči stropnih grelnih površin v skladu s specifikacijami prEN 14037-1:2011, 3.3.2, 3.3.3 in 3.3.4.
Ta del se uporablja za določitev toplotne moči, kadar se ohlajeni stropi v skladu s standardom EN 14240 uporabljajo tudi za ogrevanje.
OPOMBA   Rezultatov preskusov, pridobljenih v skladu s tem delom, ni mogoče primerjati z rezultati, pridobljenimi v skladu s standardom EN 14037-2, ker so pri odprtih stropih, konvekcijskih sestavnih delih in grelnih površinah brez zgornje izolacije podane velike neskladnosti.

General Information

Status
Published
Publication Date
20-Sep-2016
ICS
91.140.10 - Central heating systems
Technical Committee
CEN/TC 130 - Space heating appliances without integral heat sources
Drafting Committee
CEN/TC 130/WG 7 - Pre-fabricated heating panels, definitions, testing and methods for determining heat outputs
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
14-Mar-2022
Ref Project
SIST EN 14037-5:2017 - Free hanging heating and cooling surfaces for water with a temperature below 120°C - Part 5: Open or closed heated ceiling surfaces - Test method for thermal output

Buy Standard

EN 14037-5:2017EN 14037-5:2017
PreviousNext
Standard
EN 14037-5:2017
English language
21 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.An der Decke frei abgehängte Heiz- und Kühlflächen für Wasser mit einer Temperatur unter 120 °C - Teil 5: Prüfverfahren für die Wärmeleistung von offenen oder geschlossenen DeckenheizflächenPanneaux rayonnants de chauffage et de rafraîchissement alimentés avec une eau à une température inférieure à 120 °C - Partie 5 : Méthode d'essai pour la détermination de la puissance thermique des surfaces de plafond de chauffage ouverts ou fermésFree hanging heating and cooling surfaces for water with a temperature below 120°C - Part 5: Open or closed heated ceiling surfaces - Test method for thermal output91.140.10Sistemi centralnega ogrevanjaCentral heating systemsICS:Ta slovenski standard je istoveten z:EN 14037-5:2016SIST EN 14037-5:2017en01-april-2017SIST EN 14037-5:2017SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14037-5
September
t r s x ICS
{ sä s v rä s r English Version
Free hanging heating and cooling surfaces for water with a temperature below
s t r ¹C æ Part
wã Open or closed heated ceiling surfaces æ Test method for thermal output Panneaux rayonnants de chauffage et de rafraîchissement alimentés avec une eau à une température inférieure à
s t r
¹C æ Partie
w ã Méthode d 5essai pour la détermination de la puissance thermique des surfaces de plafond de chauffage ouverts ou fermés
An der Decke frei abgehängte Heizæ und Kühlflächen für Wasser mit einer Temperatur unter
s t r
¹C æ Teil
wã Prüfverfahren für die Wärmeleistung von offenen oder geschlossenen Deckenheizflächen This European Standard was approved by CEN on
s z March
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s x CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s v r u yæ wã t r s x ESIST EN 14037-5:2017

Specimen of the test report for heating capacity . 18 Bibliography . 21
module 1 m2 active surface of a heated ceiling surface 4 Symbols and units For the purposes of this document, the symbols and units given in EN 14037-1:2016 and the following apply. Table 1 — Symbols and units No. Quantity Symbol Unit 1 Installation surface Ai m2 2 Active surface Aa m2 3 Total active surface Aatot m2 4 Constant of the characteristic equation of the active surface Kact W/K nact 5 Constant of the characteristic equation of the module KactM W/(m2 K nact) 6 Constant of the characteristic equation of the installation sur-face Ktot W/K ntot 7 Exponent of the characteristic equation of the active surface nact - 8 Exponent of the characteristic equation of the installation sur-face ntot - 9 Active area ratio Ra - 10 Modular thermal output
L W/m2 11 Standard modular thermal output a
Ls W/m2 12 Standard temperature difference of a heated cooling surface when heating (15 K) a Ts K a “s” indicates that the value is in standard conditions. SIST EN 14037-5:2017
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 1264-1:2021(Main)
Water based surface embedded heating and cooling systems - Part 1: Definitions and symbols
SIST EN 1264-1:2021

The EN 1264 series gives guidelines for surface embedded heating and cooling systems installed in buildings, residential and non-residential (e.g. office, public, commercial and industrial buildings) and focuses on systems installed for the purpose of thermal comfort.
The EN 1264 series gives guidelines for water based heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. It also specifies the use of other heating media instead of water, as appropriate.
The EN 1264 series specifies standardized product characteristics by calculation and testing the thermal output of heating for technical specifications and certification. For the design, construction and operation of these systems, see EN 1264-3 and EN 1264-4 for the types A, B, C, D, H, I and J. For the types E, F and G, see the EN ISO 11855 series.
The systems specified in the EN 1264 series are adjoined to the structural base of the enclosure surfaces of the building, mounted directly or with fixing supports. The EN 1264 series does not specify ceiling systems mounted in a suspended ceiling with a designed open air gap between the system and the building structure which allows the thermally induced circulation of the air. The thermal output of these systems can be determined according to the EN 14037 series and EN 14240.
EN 1264-1 specifies system types and characteristics of water based surface embedded radiant heating and cooling systems.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1264-4:2021(Main)
Water based surface embedded heating and cooling systems - Part 4: Installation
SIST EN 1264-4:2021

The EN 1264 series gives guidelines for surface embedded heating and cooling systems installed in buildings, residential and non-residential (e.g. office, public, commercial and industrial buildings) and focuses on systems installed for the purpose of thermal comfort.
The EN 1264 series gives guidelines for water based heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. It also specifies the use of other heating media instead of water, as appropriate.
The EN 1264 series specifies standardized product characteristics by calculation and testing the thermal output of heating for technical specifications and certification. For the design, construction and operation of these systems, see EN 1264-3 and EN 1264-4 for the types A, B, C, D, H, I and J. For the types E, F and G, see the EN ISO 11855 series.
The systems specified in The EN 1264 series are adjoined to the structural base of the enclosure surfaces of the building, mounted directly or with fixing supports. The EN 1264 series does not specify ceiling systems mounted in a suspended ceiling with a designed open air gap between the system and the building structure which allows the thermally induced circulation of the air. The thermal output of these systems can be determined according to the EN 14037 series and EN 14240.
EN 1264-4 specifies uniform requirements for the design and the construction of heating and cooling floor, ceiling and wall structures to ensure that the heating/cooling systems are suited to the particular application.
The requirements specified by the EN 1264 series apply only to the components of the heating/cooling systems which are part of the heating/cooling system. EN 1264-4 does not cover other elements which are not part of the heating/cooling system.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1264-2:2021(Main)
Water based surface embedded heating and cooling systems - Part 2: Floor heating: Methods for the determination of the thermal output using calculations and experimental tests
SIST EN 1264-2:2021

The EN 1264 series gives guidelines for surface embedded heating and cooling systems installed in buildings, residential and non-residential (e.g. office, public, commercial and industrial buildings) and focuses on systems installed for the purpose of thermal comfort.
The EN 1264 series gives guidelines for water based heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. It also specifies the use of other heating media instead of water, as appropriate.
The EN 1264 series specifies standardized product characteristics by calculation and testing the thermal output of heating for technical specifications and certification. For the design, construction and operation of these systems, see EN 1264-3 and EN 1264-4 for the types A, B, C, D, H, I and J. For the types E, F and G, see the EN ISO 11855 series.
The systems specified in the EN 1264 series are adjoined to the structural base of the enclosure surfaces of the building, mounted directly or with fixing supports. The EN 1264 series does not specify ceiling systems mounted in a suspended ceiling with a designed open air gap between the system and the building structure which allows the thermally induced circulation of the air. The thermal output of these systems can be determined according to the EN 14037 series and EN 14240.
EN 1264-2 specifies hot water floor heating systems. The application of EN 1264-5 requires the prior use of EN 1264-2. EN 1264-5 specifies the conversion of the thermal output of floor heating systems determined in EN 1264-2 into the thermal output of heating surfaces embedded in walls and ceilings as well as into the thermal output of cooling surfaces embedded in floors, walls and ceilings.
EN 1264-2 specifies the boundary conditions and the test methods for the determination of the thermal output of hot water floor heating systems as a function of the temperature difference between the heating medium and the room temperature.
The thermal output is tested by a calculation method and by a measurement method. The calculation method is applicable to systems corresponding to the definitions in EN 1264-1 (type A, B, C, D, H, I and J). The measurement method gives guidance for systems not corresponding to these definitions. The calculation method and the measurement method are consistent with each other and provide correlating and adequate test results.
The test results, expressed depending on further parameters, are the standard specific thermal output and the associated standard temperature difference between the heating medium and the room temperature as well as fields of characteristic curves showing the relationship between the specific thermal output and the temperature difference between the heating medium and the room.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1264-5:2021(Main)
Water based surface embedded heating and cooling systems - Part 5: Determination of the thermal output for wall and ceiling heating and for floor, wall and ceiling cooling
SIST EN 1264-5:2021

The EN 1264 series gives guidelines for surface embedded heating and cooling systems installed in buildings, residential and non-residential (e.g. office, public, commercial and industrial buildings) and focuses on systems installed for the purpose of thermal comfort.
The EN 1264 series gives guidelines for water based heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. It also specifies the use of other heating media instead of water, as appropriate.
The EN 1264 series specifies standardized product characteristics by calculation and testing the thermal output of heating for technical specifications and certification. For the design, construction and operation of these systems, see EN 1264-3 and EN 1264-4 for the types A, B, C, D, H, I and J. For the types E, F and G, see the EN ISO 11855 series.
The systems specified in the EN 1264 series are adjoined to the structural base of the enclosure surfaces of the building, mounted directly or with fixing supports. The EN 1264 series does not specify ceiling systems mounted in a suspended ceiling with a designed open air gap between the system and the building structure which allows the thermally induced circulation of the air. The thermal output of these systems can be determined according to the EN 14037 series and EN 14240.
EN 1264-5 specifies the recalculation of values determined in EN 1264-2 for the system in question. It enables the conversion of the calculation and measurement results of EN 1264-2 into results for other surface orientations in the room, i.e. for ceiling and wall heating, as well as for the application as cooling surfaces, i.e. for floor, ceiling and wall cooling. The test results of EN 1264-2 are the basis of all calculation, whether or not the system in question is used for heating or cooling application.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1264-3:2021(Main)
Water based surface embedded heating and cooling systems - Part 3: Dimensioning
SIST EN 1264-3:2021

The EN 1264 series gives guidelines for surface embedded heating and cooling systems installed in buildings, residential and non-residential (e.g. office, public, commercial and industrial buildings) and focuses on systems installed for the purpose of thermal comfort.
The EN 1264 series gives guidelines for water based heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. It also specifies the use of other heating media instead of water, as appropriate.
The EN 1264 series specifies standardized product characteristics by calculation and testing the thermal output of heating for technical specifications and certification. For the design, construction and operation of these systems, see EN 1264-3 and EN 1264-4 for the types A, B, C, D, H, I and J. For the types E, F and G, see the EN ISO 11855 series.
The systems specified in the EN 1264 series are adjoined to the structural base of the enclosure surfaces of the building, mounted directly or with fixing supports. The EN 1264 series does not specify ceiling systems mounted in a suspended ceiling with a designed open air gap between the system and the building structure which allows the thermally induced circulation of the air. The thermal output of these systems can be determined according to EN 14037 series and EN 14240.
EN 1264-3 specifies the use in practical engineering of the results coming from EN 1264-2 and EN 1264-5.
For heating systems, physiological limitations are taken into account when specifying the surface temperatures. In the case of floor heating systems the limitations are realized by a design based on the characteristic curves and limit curves determined in accordance with EN 1264-2.
For cooling systems, only a limitation with respect to the dew point is taken into account. In predominating practice, this means that physiological limitations are included as well.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 215:2019(Main)
Thermostatic radiator valves - Requirements and test methods
SIST EN 215:2019

This document specifies definitions, requirements and test methods for thermostatic radiator valves referred to hereafter as thermostatic valves.
This standard applies to two port thermostatic valves with or without pre-setting facility and thermostatic integrated valves with or without pre-setting facility for fitting to radiators in wet central heating installations up to a water temperature of 120 °C and a nominal pressure of PN 10.
This standard further specifies the dimensions, the materials and the connection details of four series of straight and angle pattern thermostatic radiator valves of nominal pressure ≤ PN 10.
This standard can be used as reference in a CEN/CENELEC Certification Mark System on thermostatic radiator valves.

  • Standard
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14037-1:2016(Main)
Free hanging heating and cooling surfaces for water with a temperature below 120°C - Part 1: Pre-fabricated ceiling mounted radiant panels for space heating - Technical specifications and requirements
SIST EN 14037-1:2017

This European Standard defines technical specifications and requirements of free hanging prefabricated ceil-ing mounted radiant panels with an air gap between construction and the emitter (not embedded) fed with water at temperatures below 120 °C connected with a centralized heating supply source intended to be in-stalled in buildings.
The panels should be installed with an upper insulation.
The European Standard does not apply to independent heating devices.
The European Standard also defines the additional common data that the manufacturer has to provide to the trade in order to ensure the correct application of the products.
This European standard does not cover the performance of hanging accessories.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14037-4:2016(Main)
Free hanging heating and cooling surfaces for water with a temperature below 120°C - Part 4: Pre-fabricated ceiling mounted radiant panels - Test method for cooling capacity
SIST EN 14037-4:2017

This European Standard defines the technical specifications and requirements for the definition of the cooling capacity of pre-fabricated ceiling mounted radiant panels according to the specifications of EN 14037 1:2016, 3.3.1. The test according to this standard requires the measurement of the thermal output according to EN 14037 2:2016 of the model.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14037-2:2016(Main)
Free hanging heating and cooling surfaces for water with a temperature below 120°C - Part 2: Pre-fabricated ceiling mounted radiant panels for space heating - Test method for thermal output
SIST EN 14037-2:2017

This European Standard describes the test method and the test installation for determining the thermal out-put of pre-fabricated ceiling mounted radiant panels according to the specifications of EN 14037 1:2016, 3.3.1.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14037-3:2016(Main)
Free hanging heating and cooling surfaces for water with a temperature below 120°C - Part 3: Prefabricated ceiling mounted radiant panels for space heating - Rating method and evaluation of radiant thermal output
SIST EN 14037-3:2017

This European Standard describes the procedure to determine the rated thermal output (ΦD) and the mean surface temperature (trp) of pre-fabricated ceiling mounted radiant panels.
Pre-fabricated ceiling mounted radiant panels exchange heat mainly by radiation.
The test methods for determining the thermal output of pre-fabricated ceiling mounted radiant panels, as described in EN 14037 2:2016, give reliable results for comparing different products, but these results un-derstate the output obtained under real operating conditions.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day