CEN/TC 130/WG 7 - Pre-fabricated heating panels, definitions, testing and methods for determining heat outputs

This European Standard describes the test method and the test installation for determining the thermal out-put of pre-fabricated ceiling mounted radiant panels according to the specifications of EN 14037 1:2016, 3.3.1.

This European Standard defines the technical specifications and requirements for the definition of the cooling capacity of pre-fabricated ceiling mounted radiant panels according to the specifications of EN 14037 1:2016, 3.3.1. The test according to this standard requires the measurement of the thermal output according to EN 14037 2:2016 of the model.

This European Standard defines technical specifications and requirements of free hanging prefabricated ceil-ing mounted radiant panels with an air gap between construction and the emitter (not embedded) fed with water at temperatures below 120 °C connected with a centralized heating supply source intended to be in-stalled in buildings.
The panels should be installed with an upper insulation.
The European Standard does not apply to independent heating devices.
The European Standard also defines the additional common data that the manufacturer has to provide to the trade in order to ensure the correct application of the products.
This European standard does not cover the performance of hanging accessories.

This European Standard describes the test method and the test installation for determining the thermal output of ceiling mounted heating surfaces according to the specifications of prEN 14037-1:2011, 3.3.2, 3.3.3 and 3.3.4.
This part applies to determine thermal output when chilled ceilings according to EN 14240 are also used for heating.
NOTE   Test results according to this part cannot be compared with results according to EN 14037-2 because great discrepancies are given at open ceilings, convective components and heating surfaces without upper insulation.

This European Standard describes the procedure to determine the rated thermal output (ΦD) and the mean surface temperature (trp) of pre-fabricated ceiling mounted radiant panels.
Pre-fabricated ceiling mounted radiant panels exchange heat mainly by radiation.
The test methods for determining the thermal output of pre-fabricated ceiling mounted radiant panels, as described in EN 14037 2:2016, give reliable results for comparing different products, but these results un-derstate the output obtained under real operating conditions.

This European Standard defines the technical specifications and requirements of ceiling mounted hot water radiant panels, heating and cooling surfaces fed with water at temperatures below 120 °C connected with a centralized heating and/or cooling supply source.

This European Standard defines the technical specifications and requirements for the definition of the cooling capacity of ceiling mounted radiant panels according to the specifications of prEN 14037-1:2011, 3.3.1. The test according to this standard requires the measurement of the thermal output according to EN 14037-2 of the model.

This European Standard describes the test method and the test installation for determining the thermal output of ceiling mounted radiant panels according to the specifications of prEN 14037-1:2011, 3.3.1.

This European Standard describes the test method and the test installation for determining the thermal output of ceiling mounted heating surfaces according to the specifications of prEN 14037-1:2011, 3.3.2, 3.3.3 and 3.3.4.
This part applies to determine thermal output when chilled ceilings according to EN 14240 are also used for heating.
NOTE   Test results according to this part cannot be compared with results according to EN 14037-2 because great discrepancies are given at open ceilings, convective components and heating surfaces without upper insulation.

This European Standard describes the procedure to determine the rated thermal output (D) and the mean surface temperature (trp).
Ceiling mounted radiant panels exchange heat mainly by radiation.
The test methods to determine the thermal output of ceiling mounted radiant panels, as described in EN 14037-2, give reliable results for comparing different products, but these results understate the output obtained under real operating conditions.

Definition of technical specifications and requirements of prefabricated hot water radiant panels fed with water at temperatures below 120°C supplied by a remote heat source and definition of the additional common data that the manufacturer shall provide to the trade in order to ensure the correct application of the products. The document does not apply to independent heating appliances.

Definition of the test method and the test installation for determinating the thermal output of ceiling mounted radiant panels.

Definition of the test method for determining the thermal output of prefabricated ceiling mounted radiant panels fed with water at temperature below 120°C supplied from a remote source.