CEN/TS 14758-3:2006

Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifier(s) (PP-MD) - Part 3: Guidance for installation

This Technical Specification, together with ENV 1046 and EN 1610, provides a material-specific set of guidelines for the installation of piping systems made of polypropylene with mineral modifier(s) (PP-MD) in the field of non-pressure underground drainage and sewerage.
-   outside the building structure (application area code "U");
-   both buried in ground within the building structure (application area code "D") and outside the building.
This is reflected in the marking of products by "U" and "UD".

Kunststoff-Rohrleitungssysteme für erdverlegte Abwasserkanäle und -leitungen - Polypropylen mit mineralischen Additiven (PP-MD) - Teil 3: Empfehlungen für die Verlegung

Diese Technische Spezifikation legt, zusammen mit ENV 1046 und EN 1610, eine Reihe von werkstoff-spezifischen
Empfehlungen für die Verlegung von Rohrleitungssystemen aus Polypropylen mit mineralischen
Additiven (PP-MD) für Abwasserkanäle und -leitungen fest, die in erdverlegten Schwerkraftentwässerungs-systemen
"außerhalb der Gebäudestruktur (Anwendungskennzeichen "U";
"innerhalb der Gebäudestruktur (Anwendungskennzeichen "D" und außerhalb der Gebäudestruktur
eingesetzt werden.
Die Wahl des Anwendungsgebietes wird durch die Kennzeichnung der Rohrleitungsteile mit "U" bzw.
"UD" angezeigt.

Systèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement enterrés sans pression - Polypropylène avec des modificateurs minéraux (PP-MD) - Partie 3 : Guide de pose

Cevni sistemi iz polimernih materialov za odvodnjavanje in kanalizacijo, ki delujejo po težnostnem principu - Polipropilen z mineralnimi modifikatorji (PP-MD) - 3. del: Smernice za polaganje

General Information

• Status: Withdrawn
• Publication Date: 09-May-2006
• Withdrawal Date: 17-Dec-2013
• ICS: 23.040.05 - Pipeline and its parts for external sewage systems
• ICS: 23.040.20 - Plastics pipes
• ICS: 23.040.45 - Plastics fittings
• ICS: 93.030 - External sewage systems
• Technical Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Drafting Committee: CEN/TC 155/WG 10 - Systems for non-pressure drainage and sewerage - PE (solid wall)
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 18-Dec-2013
• Completion Date: 18-Dec-2013
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Ref Project: SIST-TS CEN/TS 14758-3:2006 - Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifier(s) (PP-MD) - Part 3: Guidance for installation

Relations

• Replaced By: CEN/TR 1046:2013 - Thermoplastics piping and ducting systems - Systems outside building structures for the conveyance of water or sewage - Practices for underground installation
• Effective Date: 11-Jul-2012

Standards Content (Sample)

SLOVENSKI STANDARD
01-julij-2006
Cevni sistemi iz polimernih materialov za odvodnjavanje in kanalizacijo, ki delujejo
po težnostnem principu - Polipropilen z mineralnimi modifikatorji (PP-MD) - 3. del:
Smernice za polaganje
Plastics piping systems for non-pressure underground drainage and sewerage -
Polypropylene with mineral modifier(s) (PP-MD) - Part 3: Guidance for installation
Kunststoff-Rohrleitungssysteme für erdverlegte Abwasserkanäle und -leitungen -
Polypropylen mit mineralischen Additiven (PP-MD) - Teil 3: Empfehlungen für die
Verlegung
Systemes de canalisations en plastique pour les branchements et les collecteurs
d'assainissement enterrés sans pression - Polypropylene avec des modificateurs
minéraux (PP-MD) - Partie 3 : Guide de pose
Ta slovenski standard je istoveten z: CEN/TS 14758-3:2006
ICS:
23.040.20
93.030
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

TECHNICAL SPECIFICATION
CEN/TS 14758-3
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
May 2006
ICS 93.030
English Version
Plastics piping systems for non-pressure underground drainage
and sewerage - Polypropylene with mineral modifier(s) (PP-MD)
- Part 3: Guidance for installation
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für erdverlegte
branchements et les collecteurs d'assainissement enterrés Abwasserkanäle und -leitungen - Polypropylen mit
sans pression - Polypropylène avec des modificateurs mineralischen Additiven (PP-MD) - Teil 3: Empfehlungen
minéraux (PP-MD) - Partie 3 : Guide de pose für die Verlegung
This Technical Specification (CEN/TS) was approved by CEN on 11 September 2005 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 14758-3:2006: E
worldwide for CEN national Members.

Contents  page
Foreword………………………………………………………………………………………………………………….3
1 Scope…………………………………………………………………………………………………………………4
2 Normative references…………………………………………………………………………………………….4
3 Choice of stiffness (SN) series………………………………………………………………………………….4
4 Storage in sunlight…………………………………………………………………………………………………5
5 Handling and installation at low temperature…………………………………………………………………6
6 Push-fit joints (elastomeric sealings)………………………………………………………………………….6
7 Maximum deviation from straightness…………………………………………………………………………6
8 Connection to rigid structures………………………………………………………………………………….7
9 Repairs……………………………………………………………………………………………………………….7
10 Connection to existing pipes…………………………………………………………………………………….8
11 Testing on site………………………………………………………………………………………………………8
Bibliography………………………………………………………………………………………………………………9

Foreword
This Technical Specification (CEN/TS 14758-3:2006) has been prepared by Technical Committee
CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN.
This Technical Specification is a Part of a System Standard for plastics piping systems of a particular material
for a specified application. There are a number of such System Standards.
System Standards are based on the results of the work undertaken in ISO/TC 138 "Plastics pipes, fittings and
valves for the transport of fluids", which is a Technical Committee of the International Organization for
Standardization (ISO).
They are supported by separate standards on test methods to which references are made throughout the
System Standard.
The System Standards are consistent with general standards on functional requirements and on
recommended practice for installation.
EN 14758 consists of the following Parts, under the general title Plastics piping systems for non-pressure
underground drainage and sewerage — Polypropylene with mineral modifier(s) (PP-MD)
Part 1: Specifications for pipes, fittings and the system
Part 2: Guidance for the assessment of conformity
Part 3: Guidance for installation (this Technical Specification)
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this CEN Technical Specification: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.

1 Scope
This Technical Specification, together with ENV 1046 and EN 1610, provides a material-specific set of
guidelines for the installation of piping systems made of polypropylene with mineral modifier(s) (PP-MD) in the
field of non-pressure underground drainage and sewerage.
—
outside the building structure (application area code "U");
—
both buried in ground within the building structure (application area code "D") and outside the building.
This is reflected in the marking of products by "U" and "UD".
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ENV 1046:2001, Plastics piping and ducting systems — Systems outside building structures for the
conveyance of water or sewage — Practices for installation above and below ground
EN 1610:1997, Construction and testing of drains and sewers
EN ISO 178, Plastics —Determination of flexural properties (ISO 178:2001)
EN ISO 9967, Plastics pipes — Determination of creep ratio (ISO 9967:1994)
3 Choice of stiffness (SN) series
3.1 General
PP-MD pipe is a flexible pipe.
When loaded a flexible pipe deflects and presses into the surrounding material. This generates a reaction in
the surrounding materials which controls deflection of the pipe. The amount of deflection, which occurs is
limited by the care exercised in the selection and laying of the bedding and side fill materials.
3.2 Pipes
3.2.1 Standard procedure
...