CEN/TS 15122:2005
(Main)Surfaces for sports areas - Determination of resistance of synthetic sports surfaces to repeated impact
Surfaces for sports areas - Determination of resistance of synthetic sports surfaces to repeated impact
This Technical Specification describes a method for the determination of the resistance of a synthetic sports surface to repeated impacts.
Sportböden - Bestimmung des Widerstandes von Kunststoffbelägen für Sportböden gegen wiederholte Stöße
Sols sportifs - Détermination de la résistance des sols sportifs synthétiques aux impacts répétés
Podloge za športne dejavnosti – Ugotavljanje odpornosti podlog iz umetnih snovi proti ponavljajočemu se udarcu
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2005
3RGORJH]DãSRUWQHGHMDYQRVWL±8JRWDYOMDQMHRGSRUQRVWLSRGORJL]XPHWQLKVQRYL
SURWLSRQDYOMDMRþHPXVHXGDUFX
Surfaces for sports areas - Determination of resistance of synthetic sports surfaces to
repeated impact
Sportböden - Bestimmung des Widerstandes von Kunststoffbelägen für Sportböden
gegen wiederholte Stöße
Sols sportifs - Détermination de la résistance des sols sportifs synthétiques aux impacts
répétés
Ta slovenski standard je istoveten z: CEN/TS 15122:2005
ICS:
97.150 Netekstilne talne obloge Non-textile floor coverings
97.220.10 Športni objekti Sports facilities
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
TECHNICAL SPECIFICATION
CEN/TS 15122
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
July 2005
ICS 97.150; 97.220.10
English version
Surfaces for sports areas - Determination of resistance of
synthetic sports surfaces to repeated impact
Sols sportifs - Détermination de la résistance des sols Sportböden - Bestimmung des Widerstandes von
sportifs synthétiques aux impacts répétés Kunststoffbelägen für Sportböden gegen wiederholte Stöße
This Technical Specification (CEN/TS) was approved by CEN on 18 April 2005 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 15122:2005: E
worldwide for CEN national Members.
Contents
Page
Foreword .3
1 Scope .4
2 Principle.4
3 Apparatus .4
4 Test piece .7
5 Conditioning.7
6 Procedure .7
7 Test report .8
Foreword
This document (CEN/TS 15122:2005) has been prepared by Technical Committee CEN/TC 217 “Surfaces for
sports areas”, the secretariat of which is held by BSI.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this CEN Technical Specification: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.