SLOVENSKI STANDARD
01-oktober-2008
Stroji za zemeljska dela - Varnost - 3. del: Zahteve za nakladalnike
Earth-moving machinery - Safety - Part 3: Requirements for loaders
Erdbaumaschinen - Sicherheit - Teil 3: Anforderungen für Lader
Engins de terrassement - Sécurité - Partie 3: Prescriptions applicables aux chargeuses
Ta slovenski standard je istoveten z: EN 474-3:2006/prA1
ICS:
53.100 Stroji za zemeljska dela Earth-moving machinery
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
FINAL DRAFT
EN 474-3:2006
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
June 2008
ICS 53.100
English Version
Earth-moving machinery - Safety - Part 3: Requirements for
loaders
Engins de terrassement - Sécurité - Partie 3: Prescriptions Erdbaumaschinen - Sicherheit - Teil 3: Anforderungen für
applicables aux chargeuses Lader
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 151.
This draft amendment A1, if approved, will modify the European Standard EN 474-3:2006. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 474-3:2006/prA1:2008: E
worldwide for CEN national Members.

Foreword
This document (EN 474-3:2006/prA1:2008) has been prepared by Technical Committee CEN/TC 15
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN

EN ISO 3164:2013/A1:2024(Amendment)

Earth-moving machinery - Laboratory evaluations of protective structures - Specifications for deflection-limiting volume - Amendment 1 (ISO 3164:2013/Amd 1:2024)

SIST EN ISO 3164:2014/A1:2024

2021-01-12 TC provided the Annex ZA. CCMC requested the Enquriy assessment.
2021-01-11 JF: CCMC requested the CEN/TC to provide the Annex ZA which is needed in order to request an Enquiry assessment.

Amendment
8 pages
English language
sale 10% off
e-Library read for
1 day
Amendment
9 pages
English language
sale 10% off
e-Library read for
1 day

16-Apr-2024
15-Aug-2022
53.100
2006/42/EC
M/396
CEN/TC 151

CEN

EN ISO 6165:2022(Main)

Earth-moving machinery - Basic types - Identification and vocabulary (ISO 6165:2022)

SIST EN ISO 6165:2022

This document provides vocabulary and an identification structure for classifying earth-moving machinery designed to perform the following operations:
—    excavation;
—    loading;
—    transportation;
—    drilling, spreading, compacting or trenching of earth, rock and other materials, during work, for example, on roads and dams, in quarries and mines and on building sites.
The purpose of this document is to provide a clear means to identify earth-moving machinery according to its function and design configurations which can include additional classifications according to its operating mass and control operator configuration.
Annex A provides a procedure based on the identification structure used by this document to classify the machinery and introduce detailed identifications consistent with the logic implied by the structure.
Annex B provides a hierarchy of the operator control configurations for earth-moving machinery.

Standard
23 pages
English language
sale 10% off
e-Library read for
1 day

CEN

EN 474-5:2022/AC:2022(Corrigendum)

Earth-moving machinery - Safety - Part 5: Requirements for hydraulic excavators

SIST EN 474-5:2022/AC:2022

This document together with EN 474 1:2022 deals with all significant hazards, hazardous situations and events relevant to hydraulic excavators when used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A) associated with the whole lifetime of the machine as described in EN ISO 12100:2010, 5.4.
The requirements of this document are complementary to the common requirements formulated in EN 474 1:2022. This document does not repeat the requirements of EN 474 1:2022 but supplements or modifies the requirements for hydraulic excavators.
This document does not provide requirements for main electrical circuits and drives of machinery when the primary source of energy is an external electrical supply.
The following significant and relevant hazards are not covered in this document:
— Laser;
— Lightning.
This document does not provide performance requirements for safety related functions of control system(s).
This document does not deal with towing of trailers.
This document does not deal with demolition machinery.
This document also deals with lifting operation application, shovel application, log application, grapple application, and magnetic plate application.
This document is not applicable to hydraulic excavators which are manufactured before the date of publication of this document by CEN.

Corrigendum
2 pages
English language
sale 10% off
e-Library read for
1 day

CEN

EN 474-3:2022/AC:2022(Corrigendum)

Earth-moving machinery - Safety - Part 3: Requirements for loaders

SIST EN 474-3:2022/AC:2022

This document together with EN 474 1:2022 deals with all significant hazards, hazardous situations and events relevant to loaders when used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A) associated with the whole lifetime of the machine as described in EN ISO 12100:2010, 5.4.
The requirements of this document are complementary to the common requirements formulated in EN 474 1:2022. This document does not repeat the requirements of EN 474 1:2022 but supplements or modifies the requirements for loaders.
This document does not provide requirements for main electrical circuits and drives of machinery when the primary source of energy is an external electrical supply.
This document does not provide performance requirements for safety related functions of control system(s).
The following significant and relevant hazards are not covered in this document:
—   Laser;
—   Lightning.
This document does not deal with towing of trailers.
This document does not deal with demolition machinery.
This part also deals with fork application, log handling application, single heavy object handling application and lifting operation application.
This document is not applicable to loaders which are manufactured before the date of publication of this document by CEN.
NOTE   For travelling on public roads, national traffic regulations apply (e.g. braking, steering, lighting, towing, etc.) until harmonized requirements are available.

Corrigendum
2 pages
English language
sale 10% off
e-Library read for
1 day

CEN

EN ISO 19014-2:2022(Main)

Earth-moving machinery - Functional safety - Part 2: Design and evaluation of hardware and architecture requirements for safety-related parts of the control system (ISO 19014-2:2022)

SIST EN ISO 19014-2:2022

This document specifies general principles for the development and evaluation of the machine performance level achieved (MPLa) of safety-control systems (SCS) using components powered by all energy sources (e.g. electronic, electrical, hydraulic, mechanical) used in earth-moving machinery and its equipment, as defined in ISO 6165.
The principles of this document apply to machine control systems (MCS) that control machine motion or mitigate a hazard; such systems are assessed for machine performance level required (MPLr) per ISO 19014-1 or ISO/TS 19014-5.
Excluded from the scope of this document are the following systems:
— awareness systems that do not impact machine motion (e.g. cameras and radar detectors);
— fire suppression systems, unless the activation of the system interferes with, or activates, another SCS.
Other systems or components whereby the operator would be aware of failure (e.g. windscreen wipers, head lights, etc.), or are primarily used to protect property, are excluded from this document. Audible warnings are excluded from the requirements of diagnostic coverage.
In addition, this document addresses the significant hazards as defined in ISO 12100 mitigated by the hardware components within the SCS.
This document is not applicable to EMM manufactured before the date of its publication.

Standard
51 pages
English language
sale 10% off
e-Library read for
1 day

28-Jun-2022
30-Dec-2022
53.100
2006/42/EC
M/396
CEN/TC 151

CEN

EN 474-8:2022(Main)

Earth-moving machinery - Safety - Part 8: Requirements for graders

SIST EN 474-8:2022

This document, together with EN 474 1:2022 deals with all significant hazards, hazardous situations and events relevant to graders as defined in 3.1, when used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A), associated with the whole life time of the machine as described in EN ISO 12100:2010, 5.4.
The requirements of this document are complementary to the common requirements formulated in EN 474 1:2022. This document does not repeat the requirements of EN 474 1:2022 but supplements or modifies the requirements for graders.
This document does not provide performance requirements for safety related functions of control system(s).
The following significant and relevant hazards are not covered in this document:
—   Transmission of power between self-propelled machinery (or tractor) and recipient machinery;
—   Laser;
—   Lightning.
This document is not applicable to graders manufactured before the date of publication of this document by CEN.

Standard
20 pages
English language
sale 10% off
e-Library read for
1 day

CEN

EN 474-3:2022(Main)

Earth-moving machinery - Safety - Part 3: Requirements for loaders

SIST EN 474-3:2022

Standard
37 pages
English language
sale 10% off
e-Library read for
1 day

CEN

EN 474-7:2022(Main)

Earth-moving machinery - Safety - Part 7: Requirements for scrapers

SIST EN 474-7:2022

This document, together with EN 474 1:2022, deals with all significant hazards, hazardous situations and events relevant to scrapers as defined in 3.1, except towed scrapers, when used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A), associated with the whole life time of the machine as described in EN ISO 12100:2010, 5.4.
This document does not provide performance requirements for safety related functions of control system(s).
The following significant and relevant hazards are not covered in this document:
—   Transmission of power between self-propelled machinery (or tractor) and recipient machinery;
—   Laser;
—   Lightning.
The requirements of this document are complementary to the common requirements formulated in EN 474 1:2022. This document does not repeat the requirements of EN 474 1:2022 but supplements or modifies the requirements for scrapers.
This document is not applicable to scrapers which are manufactured before the date of publication of this document by CEN.

Standard
23 pages
English language
sale 10% off
e-Library read for
1 day

CEN

EN 474-10:2022(Main)

Earth-moving machinery - Safety - Part 10: Requirements for trenchers

SIST EN 474-10:2022

This document together with EN 474 1:2022 deals with all significant hazards, hazardous situations and events relevant to trenchers as defined in Clause 3 when used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A) associated with the whole lifetime of the machine as described in EN ISO 12100:2010, 5.4.
The requirements of this document are complementary to the common requirements formulated in EN 474-1:2022. This document does not repeat the requirements of EN 474-1:2022 but supplements or modifies the requirements for trenchers.
This document deals with:
—   trenchers (3.1);
—   trenching equipment (3.2);
NOTE   In this document "trenchers" entails both "trencher" and "trenching equipment".
—   truck vacuum trenchers (3.1.2);
—   trenchers equipped with trencher backhoe equipment (3.3).
This document provides specific health and safety requirements of the trenching equipment itself and of the interface (e.g. mechanical, electric, hydraulic, controls) between the carrier-vehicle and its equipment as well as the interaction and effects on each other when used together (e.g. visibility).
This document does not apply to carrier-vehicles which are subject to other relevant regulations.
This document does not deal with continuous surface miners as defined in ISO 19224:2017, truck-trenchers that do not incorporate a vacuum extraction system or self-propelled ride-on and pedestrian controlled floor cutting-off machinery (e.g. ground saw) which are under the scope of EN 13862:2021.
This document does not provide requirements for main electrical circuits and drives of machinery when the primary source of energy is an external electrical supply.
This document does not provide performance requirements for safety related functions of control system(s).
The following significant and relevant hazards are not covered in this document:
—   Transmission of power between self-propelled machinery (or tractor) and recipient machinery;
—   Laser;
—   Lightning.
This document is not applicable to trenchers which are manufactured before the date of publication of this document by CEN.

Standard
41 pages
English language
sale 10% off
e-Library read for
1 day

CEN

EN 474-9:2022(Main)

Earth-moving machinery - Safety - Part 9: Requirements for pipelayers

SIST EN 474-9:2022

This document, together with EN 474 1:2022, deals with all significant hazards, hazardous situations and events relevant to pipelayers as defined in 3.1, when used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A) associated with the whole lifetime of the machine as described in EN ISO 12100:2010, 5.4.
The requirements of this document are complementary to the common requirements formulated in EN 474 1:2022. This document does not repeat the requirements of EN 474 1:2022 but supplements or modifies the requirements for pipelayers.
This document also specifies additional requirements for rear mounted winches.
This document does not provide performance requirements for safety related functions of control system(s).
The following significant and relevant hazards are not covered in this document:
—   Transmission of power between self-propelled machinery (or tractor) and recipient machinery;
—   Laser;
—   Lightning.
Pipelayers with rotating upper structure are excluded from the scope of this document.
This document is not applicable to pipelayers manufactured before the date of publication of this document by CEN.

Standard
25 pages
English language
sale 10% off
e-Library read for
1 day