EN ISO 2898-1:1999

Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2898-1:1996)

Establishes a system of designation for plasticized poly(vinyl chloride) (PVC-P) which may be used as the basis for specifications. PVC-P plastics are differentiated by a classification system based on appropriate levels of properties such as Shore hardness, density and torsional-stiffness temperature at 300 MPa and on information about physical form, intended application, additives and colorants. Replaces the second edition.

Kunststoffe - Weichmacherhaltige Polyvinylchlorid (PVC-P)-Formmassen - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 2898-1:1996)

Plastiques - Matériaux à base de poly(chlorure de vinyle) plastifié (PVC-P) pour moulage et extrusion - Partie 1: Système de désignation et base de spécification (ISO 2898-1:1996)

La présente partie de l'ISO 2898 est applicable à toutes les compositions plastifiées d'homopolymères et de copolymères qui contiennent au moins 50 % (m/m) de chlorure de vinyle. Elle est également applicable aux compositions plastifiées qui contiennent du poly(chlorure de vinyle) chloré et à celles qui contiennent des mélanges constitués d'un ou plusieurs polymères parmi ceux susmentionnés, sous réserve que la teneur totale en ces polymères soit égale à au moins 50 % (m/m) du mélange de polymères de la composition. La présente partie de l'ISO 2898 s'applique aux matériaux prêts à l'emploi sous forme de poudre (mélange sec), grains ou granulés, non modifiés ou modifiés par des colorants, additifs, charges, etc. La présente partie de l'ISO 2898 ne s'applique ni aux plastiques cellulaires, ni aux compositions en pâte (plastisols). Le fait que des matériaux aient la même désignation n'implique pas qu'ils présentent nécessairement les mêmes performances. La présente partie de l'ISO 2898 ne comporte pas de données sur la conception, la performance ou les conditions de mise en oeuvre qui peuvent être exigées pour spécifier un matériau pour une application et/ou une méthode de mise en oeuvre. Si de telles propriétés additionnelles sont nécessaires, elles doivent être déterminées conformément aux méthodes d'essai prescrites dans l'ISO 2898-2, le cas échéant. Afin de prescrire un matériau thermoplastique pour une application particulière ou d'assurer une méthode de mise en oeuvre reproductible, des exigences additionnelles peuvent être indiquées dans le bloc de données 5 (voir article 3, premier alinéa).

Polimerni materiali - Materiali za oblikovanje in ekstrudiranje iz mehčanega polivinilklorida (PVC-P) - 1. del: Sistem označevanja in podlage za specifikacije (ISO 2898-1:1996)

General Information

• Status: Withdrawn
• Publication Date: 22-Jun-1999
• Withdrawal Date: 26-May-2020
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249 - Plastics
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 27-May-2020
• Ref Project: SIST EN ISO 2898-1:2000 - Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2898-1:1996)

Relations

• Replaced By: EN ISO 24023-1:2020 - Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 24023-1:2020)
• Effective Date: 03-Jun-2020

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 2898-1:2000
01-maj-2000
3ROLPHUQLPDWHULDOL0DWHULDOL]DREOLNRYDQMHLQHNVWUXGLUDQMHL]PHKþDQHJD
SROLYLQLONORULGD39&3GHO6LVWHPR]QDþHYDQMDLQSRGODJH]DVSHFLILNDFLMH
,62
Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part
1: Designation system and basis for specifications (ISO 2898-1:1996)
Kunststoffe - Weichmacherhaltige Polyvinylchlorid (PVC-P)-Formmassen - Teil 1:
Bezeichnungssystem und Basis für Spezifikationen (ISO 2898-1:1996)
Plastiques - Matériaux a base de poly(chlorure de vinyle) plastifié (PVC-P) pour moulage
et extrusion - Partie 1: Systeme de désignation et base de spécification (ISO 2898-
1:1996)
Ta slovenski standard je istoveten z: EN ISO 2898-1:1999
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 2898-1:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 2898-1:2000

---------------------- Page: 2 ----------------------

SIST EN ISO 2898-1:2000

---------------------- Page: 3 ----------------------

SIST EN ISO 2898-1:2000

---------------------- Page: 4 ----------------------

SIST EN ISO 2898-1:2000

---------------------- Page: 5 ----------------------

SIST EN ISO 2898-1:2000

---------------------- Page: 6 ----------------------

SIST EN ISO 2898-1:2000
I NTE R NAT1 O NAL
IS0
STANDARD 2898- I
Third edition
1996-08-1 5
Plastics - Plasticized poly(viny1 chloride)
(PVC-P) moulding and extrusion
materials -
Part 1:
Designation system and basis for
specifications
Plastiques - Matériaux à base de poly(ch1orure de vinyle) plastifié (PVC-P)
pour moulage et extrusion -
Partie 1: Système de désignation et base de spécification
Reference number
IS0 2898-1 11 996(E)

---------------------- Page: 7 ----------------------

SIST EN ISO 2898-1:2000
IS0 2898-1 :1996(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide fed-
eration of national standards bodies (IS0 member bodies). The work of
preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 YO of the member bodies casting
a vote.
International Standard IS0 2898-1 was prepared by Technical Committee
lSO/lC 61, Plastics, Subcommittee SC 9, Thermoplastics.
This third edition cancels and replaces the second edition
(IS0 2898-1 :I 986) and includes the following changes:
the text has been brought into line with latest version of the so-called
"frame text";
"tape manufacture" has been added in data block 2 as a possible
application.
IS0 2898 consists of the following parts, under the general title Plastics -
Plasticized polyfvin y1 chloride) (PVC-P) moulding and extrusion materials.
-
Part I: Designation system and basis for specifications
-
Part 2: Preparation of test specimens and determination of properties
O IS0 1996
All rights reserved Unless otherwise specified, no part of this publication may be
reproduced or utilized in any form or by any means, electronic or mechanical, including
photocopying and microtilm without permission in writing from the publisher
International Organization for Standardization
Case Postale 56 CH-1 21 1 Geneve 20 Switzerland
Printed in Switzerland
II

---------------------- Page: 8 ----------------------

SIST EN ISO 2898-1:2000
INTERNATIONAL STANDARD 0 IS0 IS0 2898-1 : 1996( E)
Plastics - Plasticized poly(viny1 chloride) (PVC-P) moulding
-
and extrusion materials
Part 1:
Designation system and basis for specifications
1 Scope
1.1 This part of IS0 2898 establishes a system of designation for plasticized thermoplastic material which may be
used as the basis for specifications.
1.2 The types of PVC-P plastics are differentiated from each other by a classification system based on appropriate
levels of the designatory properties
a) Shore hardness
b) density
torsional-stiffness temperature at 300 MPa
c)
and on information about physical form, intended application and/or method of processing, important properties,
additives and colorants.
1.3 This part of IS0 2898 is applicable to all plasticized compositions of homopolymers and copolymers that con-
tain at least 50 Yo (m/m) of vinyl chloride. It is also applicable to plasticized compositions con
...