EN 1800:2006
(Main)Transportable gas cylinders - Acetylene cylinders - Basic requirements, definitions and type testing
Transportable gas cylinders - Acetylene cylinders - Basic requirements, definitions and type testing
This European Standard specifies the basic requirements for acetylene cylinders with a maximum nominal water capacity of 150 l, including:
- the procedure for type testing;
- the procedure for production/batch testing;
- the methods for determining the maximum permissible settled pressure;
- the method for determining the porosity of the porous material;
It does not include details of designs for the cylinder shell.
Ortsbewegliche Gasflaschen - Acetylenflaschen - Grundanforderungen, Definitionen und Typprüfung
Diese Europäische Norm legt die grundlegenden Anforderungen für Acetylenflaschen mit einem Nenn-Fassungsraum von maximal 150 l fest, einschließlich:
a) des Verfahrens für die Typprüfung;
b) des Verfahrens für die Herstellungs-/Stichprobenprüfung;
c) der Verfahren zur Bestimmung des maximal zulässigen festgelegten Druckes;
d) des Verfahrens zur Bestimmung der Porosität des porösen Materials.
Sie enthält keine Angaben über die Gestaltungen des Flaschenkörpers.
Bouteilles à gaz transportables - Bouteilles d'acétylène - Exigences fondamentales, définitions et essais de type
La présente Norme européenne spécifie les exigences fondamentales pour les bouteilles d�acétylène ayant
une contenance nominale maximale en eau de 150 l, y compris :
.le mode opératoire pour les essais de type ;
.le mode opératoire pour les essais de fabrication et par lots ;
.la méthode de détermination de la pression de travail ;
.la méthode de détermination de la porosité de la masse poreuse.
Elle ne traite pas en détail la conception du corps de la bouteille.
Premične plinske jeklenke – Jeklenke za acetilen – Osnovne zahteve, definicije in preskus tipa
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Transportable gas cylinders - Acetylene cylinders - Basic requirements, definitions and type testingBouteilles a gaz transportables - Bouteilles d'acétylene - Exigences fondamentales, définitions et essais de typeOrtsbewegliche Gasflaschen - Acetylenflaschen - Grundanforderungen, Definitionen und TypprüfungTa slovenski standard je istoveten z:EN 1800:2006SIST EN 1800:2007en23.020.30MHNOHQNHPressure vessels, gas cylindersICS:SIST EN 1800:19991DGRPHãþDSLOVENSKI
STANDARDSIST EN 1800:200701-april-2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1800November 2006ICS 23.020.30Supersedes EN 1800:1998
English VersionTransportable gas cylinders - Acetylene cylinders - Basicrequirements, definitions and type testingBouteilles à gaz transportables - Bouteilles d'acétylène -Exigences fondamentales, définitions et essais de typeOrtsbewegliche Gasflaschen - Acetylenflaschen -Grundanforderungen, Definitionen und TypprüfungThis European Standard was approved by CEN on 29 September 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1800:2006: E
Procedure for type testing of dissolved acetylene cylinders.11 Annex B (normative)
Determination of porosity of the porous material.15 Annex C (normative)
Working pressure.16 Annex D (normative)
Production/batch test procedures for the preparation of porous material of acetylene cylinders.17 Bibliography.18
1 Scope This European Standard specifies the basic requirements for acetylene cylinders with a maximum nominal water capacity of 150 l, including: a) the procedure for type testing; b) the procedure for production/batch testing; c) the methods for determining the maximum permissible settled pressure; d) the method for determining the porosity of the porous material; It does not include details of designs for the cylinder shell. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1964-1, Transportable gas cylinders — Specification for the design and construction of refillable transportable seamless steel gas cylinders of water capacities from 0,5 litre up to and including 150 litres — Part 1: Cylinders made from seamless steel with an Rm value of less than 1 100 MPa EN 1975, Transportable gas cylinders — Specification for the design and construction of refillable transportable seamless aluminium and aluminium alloy gas cylinders of capacity from 0,5 litre up to 150 litres EN 13322-1, Transportable gas cylinders — Refillable welded steel gas cylinders — Design and construction — Part 1: Carbon steel EN ISO 10297, Transportable gas cylinders — Cylinder valves — Specification and type testing (ISO 10297:2006) prEN ISO 11117, Gas cylinders — Valve protection caps and valve guards — Design, construction and tests (ISO/DIS 11117:2006) EN ISO 13769, Gas cylinders — Stamp marking (ISO 13769:2002) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 acetylene cylinder cylinder containing a porous material with or without solvent for the storage of acetylene NOTE For solvent free acetylene cylinders see Clause 6. 3.2 tare weight see EN ISO 13769 and 4.5
Valve guards and caps for use with acetylene cylinders shall conform to the requirements of prEN ISO 11117. NOTE Other accessories should conform to the requirements of appropriate European Standards, when available. 5 Approval procedures 5.1 General Representative cylinders, selected according to 5.3 by or on behalf of the approving organisation shall withstand successfully the type tests as required in 5.4 prior to type approval being granted to the request made by the manufacturer of the porous material (see 5.2). 5.2 Requests for approval 5.2.1 A request for the approval of acetylene cylinders may cover a range of different volumes provided that: a) the construction is similar (either seamless cylinders or cylinders with circumferential joggle welds or cylinders with butt welds only); b) the nominal outside diameter of the cylinder falls within the range of either: 1) up to and inclusive of 270 mm or 2) greater than 270 mm; c) the acetylene solvent ratios are the same; d) the maximum acetylene content per litre water capacity is the same; e) the cylinders contain the same porous material from the same factory and, the same solvent; f) the cylinder shells are made from the same type of material (steel or aluminium etc.).
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.