EN 15182-3:2019
(Main)Portable equipment for projecting extinguishing agents supplied by firefighting pumps - Hand-held branchpipes for fire service use - Part 3: Smooth bore jet and/or one fixed spray jet angle branchpipes PN 16
Portable equipment for projecting extinguishing agents supplied by firefighting pumps - Hand-held branchpipes for fire service use - Part 3: Smooth bore jet and/or one fixed spray jet angle branchpipes PN 16
In addition to the requirements given in EN 15182-1:2019, this document applies to hand-held branchpipes with smooth bore jet and/or one fixed spray jet angle branchpipes with a nominal pressure of 16 bar (1,6 MPa) PN 16, with a maximum flow rate up to 1 000 l/min at a reference pressure of 6 bar (0,6 MPa). It deals with:
- safety requirements;
- performance requirements;
- test methods.
This document applies to branchpipes as defined in Annex A of EN 15182-1:2019.
WARNING 1 — These branchpipes offer no or inadequate protection for firefighters when the spray angle is less than 30 ° and therefore, are not be used in high risk firefighting situations such as internal attack.
WARNING 2 — These branchpipes should not be used when fighting fires in or near electrical installations when the spray angle is less than 30° without written authorization from the manufacturer in the manual. This authorization from the manufacturer includes safety distances.
Tragbare Geräte zum Ausbringen von Löschmitteln, die mit Feuerlöschpumpen gefördert werden - Strahlrohre für die Brandbekämpfung - Teil 3: Strahlrohre mit Vollstrahl und/oder einem unveränderlichen Sprühstrahlwinkel PN 16
Zusätzlich zu den in EN 15182-1:2019 angegebenen Anforderungen gilt der vorliegende Teil dieser Normenreihe für Strahlrohre mit Vollstrahl und/oder einem unveränderlichen Sprühstrahlwinkel mit einem Nenndruck von 16 bar (1,6 MPa) PN 16, mit einem maximalen Volumenstrom von bis zu 1 000 l/min bei einem Referenzdruck von 6 bar (0,6 MPa). Behandelt werden:
- Sicherheitsanforderungen;
- Leistungsanforderungen;
- Prüfverfahren.
Dieses Dokument gilt für Strahlrohre nach EN 15182-1:2019, Anhang A.
WARNUNG 1 — Diese Strahlrohre bieten keinen oder nur unzureichenden Schutz für Feuerwehrleute, wenn der Sprühwinkel weniger als 30° beträgt, und werden daher nicht in Situationen mit hohem Risiko bei der Brandbekämpfung, wie z. B. bei Innenangriffen, eingesetzt.
WARNUNG 2 — Diese Strahlrohre sollten nicht für die Brandbekämpfung in oder an elektrischen Anlagen eingesetzt werden, wenn der Sprühwinkel weniger als 30° beträgt, sofern dies vom Hersteller nicht schriftlich im Handbuch autorisiert wurde. Diese Autorisierung des Herstellers schließt Mindestabstände ein.
Equipement portable de projection d’agents d’extinction alimenté par des pompes à usage incendie - Lances à main destinées aux services d'incendie et de secours - Partie 3 : Lances à jet plein et/ou une diffusion à angle fixe PN 16
En complément des prescriptions données dans l’EN 15182-1:2019, le présent document s‘applique aux
lances à main à jet plein et/ou une diffusion à angle fixe, de pression nominale de 16 bar (16 MPa) PN 16,
de débit maximal 1 000 l/min à une pression de référence de 6 bar (0,6 MPa). Il traite :
- des prescriptions de sécurité ;
- des prescriptions de performances ;
- des méthodes d’essai.
Le présent document s’applique aux lances définies dans l’Annexe A de EN 15182-1:2019.
AVERTISSEMENT 1 — Ces lances offrent une protection insuffisante, voire nulle, aux pompiers lorsque
l’angle de diffusion est inférieur à 30°, et de ce fait elles ne sont pas utilisées dans des situations de lutte
contre l’incendie à haut risque, telles que l’attaque en intérieur.
AVERTISSEMENT 2 — Il convient de ne pas utiliser ces lances lorsque l’on combat un incendie qui s’est
déclaré dans des installations électriques ou qui a été provoqué par ces dernières avec un angle de
diffusion inférieur à 30°, sans l’autorisation écrite du fabricant dans la notice d’instructions. Cette
autorisation du fabricant comporte les distances de sécurité.
Prenosna oprema za črpanje in uporabo gasilnega sredstva iz gasilskih črpalk - Gasilski ročniki - 3. del: Ročniki PN 16 s polnim curkom in/ali z razpršenim curkom pod določenim fiksnim kotom
Poleg zahtev, navedenih v standardu EN 15182-1, se ta dokument uporablja za ročnike PN 16 s polnim curkom in/ali z razpršenim curkom pod določenim fiksnim kotom ter z največjim pretokom 1000 l/min pri referenčnem tlaku 6 barov (0,6 MPa). Obravnava:
– varnostne zahteve;
– zahteve glede zmogljivosti;
– preskusne metode.
Ta dokument se uporablja za ročnike, kot je opredeljeno v dodatku A standarda EN 15182-1.
OPOZORILO 1: Ti ročniki gasilcem ne zagotavljajo zaščite oz. zagotavljajo nezadostno zaščito, kadar je kot razpršenega curka manjši od 30°, zato se jih ne sme uporabljati pri izredno tveganih situacijah gašenja, kot je notranji napad.
OPOZORILO 2: Teh ročnikov se ne sme uporabljati pri gašenju požarov na električnih inštalacijah ali v njihovi bližini, kadar je kot razpršenega curka manjši od 30°, brez pisne odobritve proizvajalca v priročniku. Ta odobritev proizvajalca mora vključevati varnostne razdalje.
General Information
- Status
- Published
- Publication Date
- 13-Aug-2019
- Withdrawal Date
- 28-Feb-2020
- Technical Committee
- CEN/TC 192 - Fire service equipment
- Drafting Committee
- CEN/TC 192/WG 8 - Hand-held branchpipes for fire service use
- Current Stage
- 9060 - Closure of 2 Year Review Enquiry - Review Enquiry
- Start Date
- 04-Mar-2025
- Completion Date
- 04-Mar-2025
Relations
- Effective Date
- 21-Aug-2019
Overview
EN 15182-3:2019 is a European standard developed by CEN that specifies the requirements for hand-held branchpipes used in fire service operations. These branchpipes are designed for projecting extinguishing agents supplied by firefighting pumps, specifically those with a smooth bore jet or a fixed spray jet angle under nominal pressure PN 16 (16 bar, 1.6 MPa). The standard applies to branchpipes with a maximum flow rate up to 1000 liters per minute at a reference pressure of 6 bar.
This document is an essential reference for manufacturers, testing bodies, and fire services, ensuring the safety, efficiency, and reliability of branchpipes used in firefighting. It complements the general requirements established in EN 15182-1:2019 and focuses on specific performance, safety, and testing criteria for these equipment types.
Key Topics
Safety Requirements
EN 15182-3 emphasizes critical safety warnings:- Branchpipes with spray angles less than 30° provide inadequate protection for firefighters and must not be used for high-risk operations such as internal fire attacks.
- Their use near or on electrical installations is restricted without explicit written authorization from the manufacturer, including safety distance guidelines.
Performance Requirements
The standard defines clear mechanical, hydraulic, and operational performance criteria, including:- Maximum dimensions and mass limits to ensure maneuverability.
- Torque limitations for operating elements such as levers and valve handles to allow safe, easy handling without excessive force.
- Spray jet characteristics, mandating a minimum spray angle of 15° for fixed spray jets, and specifying flow rate accuracy with permissible deviations.
- Minimum effective throw distance requirements, ensuring the branchpipe delivers water streams effectively at specified flow rates.
Test Methods
EN 15182-3 sets detailed testing protocols to verify compliance with requirements:- Leak-tightness tests under nominal and test pressures to confirm no leakage during operation.
- Hydrostatic pressure tests simulating water hammer effects up to burst pressure (60 bar) to validate structural integrity.
- Measurement of torque forces, spray angles, flow rates, and effective throw distances conducted under controlled conditions.
Mechanical Specifications
- Flow rates up to 1000 l/min and nominal pressure of 16 bar (PN 16).
- Branchpipes must adhere to dimension and mass limits for different flow rate capacities to optimize handling.
- Operating elements must maintain designated torque values and defined force ranges for components with detents to ensure durability and user safety.
Applications
EN 15182-3:2019 branchpipes are critical equipment for firefighting teams engaging with portable devices connected to pumps. Their applications include:
- Outdoor firefighting operations where a fixed spray angle or smooth bore jet is sufficient for extinguishing flames at a safe distance.
- Use with fire trucks or fixed pump systems requiring reliable handheld spray tools capable of delivering extinguishing agents at high pressure.
- Environments where safety and ergonomic handling are mandatory to reduce firefighter fatigue and exposure risks.
- Situations necessitating consistent flow rates and effective water throw for efficient flame suppression without endangering personnel in proximity.
However, it is important to heed the standard’s warnings: these branchpipes are not suitable for high-risk internal firefighting attacks or operations near electrical hazards unless specifically authorized.
Related Standards
- EN 15182-1:2019 – Specifies common requirements for hand-held firefighting branchpipes and forms the foundational document for EN 15182-3.
- Other parts of the EN 15182 series address variations in branchpipe designs and pressures, offering comprehensive guidelines for firefighting equipment across different use cases.
- References to ISO and IEC terminological databases facilitate uniform definitions and understanding across firefighting and safety standards worldwide.
Keywords
Firefighting branchpipes, handheld branchpipes, smooth bore jet, fixed spray angle branchpipe, firefighting pumps, firefighting equipment standard, EN 15182-3:2019, fire service use, extinguishing agents, fire safety equipment, PN16 branchpipes, fire hose nozzle standards, firefighting tool requirements, safety regulations for firefighting instruments.
Adhering to EN 15182-3:2019 ensures fire services equipped with portable firefighting branchpipes meet stringent European safety, performance, and reliability criteria, advancing firefighting efficiency and firefighter protection in operational environments.
Frequently Asked Questions
EN 15182-3:2019 is a standard published by the European Committee for Standardization (CEN). Its full title is "Portable equipment for projecting extinguishing agents supplied by firefighting pumps - Hand-held branchpipes for fire service use - Part 3: Smooth bore jet and/or one fixed spray jet angle branchpipes PN 16". This standard covers: In addition to the requirements given in EN 15182-1:2019, this document applies to hand-held branchpipes with smooth bore jet and/or one fixed spray jet angle branchpipes with a nominal pressure of 16 bar (1,6 MPa) PN 16, with a maximum flow rate up to 1 000 l/min at a reference pressure of 6 bar (0,6 MPa). It deals with: - safety requirements; - performance requirements; - test methods. This document applies to branchpipes as defined in Annex A of EN 15182-1:2019. WARNING 1 — These branchpipes offer no or inadequate protection for firefighters when the spray angle is less than 30 ° and therefore, are not be used in high risk firefighting situations such as internal attack. WARNING 2 — These branchpipes should not be used when fighting fires in or near electrical installations when the spray angle is less than 30° without written authorization from the manufacturer in the manual. This authorization from the manufacturer includes safety distances.
In addition to the requirements given in EN 15182-1:2019, this document applies to hand-held branchpipes with smooth bore jet and/or one fixed spray jet angle branchpipes with a nominal pressure of 16 bar (1,6 MPa) PN 16, with a maximum flow rate up to 1 000 l/min at a reference pressure of 6 bar (0,6 MPa). It deals with: - safety requirements; - performance requirements; - test methods. This document applies to branchpipes as defined in Annex A of EN 15182-1:2019. WARNING 1 — These branchpipes offer no or inadequate protection for firefighters when the spray angle is less than 30 ° and therefore, are not be used in high risk firefighting situations such as internal attack. WARNING 2 — These branchpipes should not be used when fighting fires in or near electrical installations when the spray angle is less than 30° without written authorization from the manufacturer in the manual. This authorization from the manufacturer includes safety distances.
EN 15182-3:2019 is classified under the following ICS (International Classification for Standards) categories: 13.220.10 - Fire-fighting. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 15182-3:2019 has the following relationships with other standards: It is inter standard links to EN 15182-3:2007+A1:2009. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
You can purchase EN 15182-3:2019 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of CEN standards.
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2019
Nadomešča:
SIST EN 15182-3:2007+A1:2010
Prenosna oprema za črpanje in uporabo gasilnega sredstva iz gasilskih črpalk -
Gasilski ročniki - 3. del: Ročniki PN 16 s polnim curkom in/ali z razpršenim curkom
pod določenim fiksnim kotom
Portable equipment for projecting extinguishing agents supplied by firefighting pumps -
Hand-held branchpipes for fire service use - Part 3: Smooth bore jet and/or one fixed
spray jet angle branchpipes PN 16
Tragbare Geräte zum Ausbringen von Löschmitteln, die mit Feuerlöschpumpen gefördert
werden - Strahlrohre für die Brandbekämpfung - Teil 3: Strahlrohre mit Vollstrahl
und/oder einem unveränderlichem Sprühstrahlwinkel PN 16
Equipement portable de projection d’agents d’extinction alimenté par des pompes à
usage incendie - Lances à main destinées aux services d'incendie et de secours - Partie
3: Lances à jet plein et/ou une diffusion à angle fixe PN 16
Ta slovenski standard je istoveten z: EN 15182-3:2019
ICS:
13.220.10 Gašenje požara Fire-fighting
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 15182-3
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2019
EUROPÄISCHE NORM
ICS 13.220.10 Supersedes EN 15182-3:2007+A1:2009
English Version
Portable equipment for projecting extinguishing agents
supplied by firefighting pumps - Hand-held branchpipes
for fire service use - Part 3: Smooth bore jet and/or one
fixed spray jet angle branchpipes PN 16
Equipement portable de projection d'agents Tragbare Geräte zum Ausbringen von Löschmitteln, die
d'extinction alimenté par des pompes à usage incendie mit Feuerlöschpumpen gefördert werden - Strahlrohre
- Lances à main destinées aux services d'incendie et de für die Brandbekämpfung - Teil 3: Strahlrohre mit
secours - Partie 3 : Lances à jet plein et/ou une Vollstrahl und/oder einem unveränderlichen
diffusion à angle fixe PN 16 Sprühstrahlwinkel PN 16
This European Standard was approved by CEN on 10 June 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15182-3:2019 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Requirements and verification . 4
4.1 General . 4
4.2 Mechanical characteristics . 5
4.2.1 Dimensions and mass . 5
4.2.2 Operating and handling elements . 5
4.2.3 Jet spray angle . 6
4.3 Hydraulic characteristics . 6
4.3.1 General . 6
4.3.2 Flow rates . 6
4.3.3 Effective throw . 7
4.4 Leak-tightness . 9
4.5 Hydrostatic behaviour. 9
European foreword
This document (EN 15182-3:2019) has been prepared by Technical Committee CEN/TC 192 “Fire and
rescue service equipment”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2020, and conflicting national standards
shall be withdrawn at the latest by February 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 15182-3:2007+A1:2009.
Compared to EN 15182-3:2007+A1:2009 the following changes have been made:
— each verification has been placed under the corresponding requirement;
— a test to measure the forces needed to move the rotating elements which have detents (4.2.2) has
been added;
— the requirements for flowrates (4.3.2) have been updated;
— the verifications for leak-tightness (4.4) and hydrostatic behaviour (4.5) have been updated;
— improvement of the wording/editorial changes.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United K
...
Die Norm EN 15182-3:2019 beschäftigt sich mit tragbaren Geräten zur Ausbringung von Löschmitteln, die von Feuerwehrpumpen gespeist werden. Im Fokus stehen hierbei Handrohre mit glattem Strahl und/oder einem festen Sprühwinkel, die für den Einsatz im Feuerwehrdienst konzipiert sind. Mit einem Nennbetriebsdruck von 16 bar (1,6 MPa) und einer maximalen Durchflussrate von bis zu 1.000 l/min bei einem Referenzdruck von 6 bar (0,6 MPa) bietet diese Norm eine umfassende Grundlage für die Qualität und Sicherheit dieser lebenswichtigen Ausrüstung. Die Stärken der Norm liegen in den klar definierten Sicherheits- und Leistungsanforderungen sowie den getesteten Methoden, die sicherstellen, dass die Handrohre den strengen Standards entsprechen. Diese Norm gewährleistet, dass Feuerwehrleute unter ordnungsgemäßen Bedingungen effektiv und sicher arbeiten können, indem sie umfassende Richtlinien zur Nutzung und den Eigenschaften der Handrohre bereitstellt. Ein wichtiger Aspekt der Norm ist die explizite Warnung vor der Anwendung der Handrohre in hochriskanten Situationen, insbesondere wenn der Sprühwinkel unter 30° liegt. Dies ist entscheidend für die Sicherheit der Feuerwehrkräfte, da diese Bedingungen das Risiko erhöhen können. Auch die Vorgaben zur Vermeidung der Verwendung in der Nähe von elektrischen Installationen unterlines Wohnverhältnissen zeigen die Relevanz der Norm für den praktischen Einsatz. Insgesamt zeigt die EN 15182-3:2019, wie wichtig standardisierte Anforderungen für den Brandschutz sind. Die Norm trägt dazu bei, die erforderliche Sicherheit und Effizienz bei der Bekämpfung von Bränden zu gewährleisten, indem sie sowohl technische Spezifikationen als auch Sicherheitsvorkehrungen klar kommuniziert. Damit ist sie ein unverzichtbares Dokument für die Feuerwehr und deren Ausrüstungsmanagement.
The standard EN 15182-3:2019 establishes critical requirements for hand-held branchpipes used in firefighting, specifically those designed for projecting extinguishing agents supplied by firefighting pumps. The document's scope is comprehensive, building upon the foundational safety and performance criteria outlined in EN 15182-1:2019. It focuses on branchpipes equipped with a smooth bore jet and/or fixed spray jet angle, functioning effectively under a nominal pressure of 16 bar (1.6 MPa) and accommodating maximum flow rates up to 1,000 l/min at a reference pressure of 6 bar (0.6 MPa). One of the strengths of EN 15182-3:2019 is its detailed inclusion of safety requirements and performance standards, ensuring that equipment meets stringent operational protocols. The specification of test methods reinforces the standard's reliability, facilitating uniformity in assessing branchpipe functionality and ensuring that they are tested under comparable conditions. This aligns well with current safety practices in fire service operations, promoting effective risk management. The relevance of this standard is especially pronounced given the warnings it entails regarding the application of branchpipes in high-risk scenarios. For instance, the caution against using these devices with a spray angle less than 30° in hazardous environments underscores the importance of adhering strictly to guidelines for firefighter protection. Additionally, the stipulation that branchpipes should not be utilized near electrical installations without prior manufacturer authorization highlights the standard's proactive approach to safety. Overall, EN 15182-3:2019 serves as a vital document that not only details the operational capabilities of hand-held branchpipes for fire service use but also enhances safety awareness among personnel. By ensuring a robust framework for equipment use, this standard contributes significantly to improved firefighting effectiveness and safety.
La norme SIST EN 15182-3:2019 se présente comme un document essentiel pour les équipements portables servant à projeter des agents extincteurs fournis par des pompes de lutte contre l'incendie. Cette norme se concentre spécifiquement sur les canons à main avec jet lisse et/ou un angle de jet fixe de pulvérisation, opérant à une pression nominale de 16 bars (1,6 MPa), et pouvant gérer un débit maximum de 1 000 l/min à une pression de référence de 6 bars (0,6 MPa). L'un des principaux atouts de cette norme est son approche rigoureuse envers les exigences de sécurité. En effet, elle met en lumière les risques associés aux branches à jet lisse, notamment les limitations d'utilisation dans des situations à haut risque, telles que celles impliquant un angle de spray inférieur à 30 °. Cela garantit que les utilisateurs sont informés des dangers potentiels et qu'ils peuvent prendre des décisions éclairées et conformes aux recommandations de sécurité. En termes de performances, les exigences spécifiques établies dans cette norme permettent d'assurer une fiabilité et une efficacité accrues des branchements. Les méthodes d'essai définies contribuent à garantir que les équipements répondent aux standards requis en matière de performance, ce qui renforce la confiance des professionnels lors de leur utilisation sur le terrain. La pertinence de la norme SIST EN 15182-3:2019 est indéniable, surtout dans un contexte où la sécurité des pompiers est primordiale. En établissant des critères clairs et des avertissements importants sur l'utilisation de ces équipements, la norme permet d'améliorer les pratiques de lutte contre les incendies et de protéger la vie des intervenants. Grâce à cette norme, les équipes d'intervention peuvent mieux se préparer à affronter des situations d'urgence tout en minimisant les risques associés à l'utilisation de matériel inapproprié ou non conforme. En résumé, la norme SIST EN 15182-3:2019 représente une avancée significative dans la réglementation des équipements de lutte contre l'incendie, en offrant des lignes directrices solides sur la sécurité, la performance et les essais nécessaires lors de l'utilisation de canons à main.
標準SIST EN 15182-3:2019は、消防ポンプから供給される消火剤を投影するための携帯機器に関する詳細な要件を規定しており、特に手持ち型の分岐管について焦点を当てています。この標準は、滑らかなボアジェットおよび固定スプレイ角の分岐管に適用され、PN 16という nominal pressure 16 bar (1.6 MPa)の範囲で、最大流量1,000 l/minを6 bar (0.6 MPa)の基準圧でサポートします。 この文書は、安全要件、性能要件、試験方法を包括的に扱っており、EN 15182-1:2019の附属書Aに定義されている分岐管に適用されます。特に注目すべきは、消防士の安全に対する警告であり、スプレイ角が30°未満の場合には、十分な保護が提供されないことが強調されています。例えば、内部攻撃などの高リスクな消火状況では使用が推奨されていないため、現場のリスク評価を行うことが重要です。 また、スプレイ角が30°未満の場合、電気設備の近くでの使用にはメーカーからの書面による承認が必要であり、この承認には安全距離に関する情報も含まれています。このような厳格な要件は、安全な操作を確保するために不可欠であり、消防士や現場の安全を重視した設計であることを示しています。 SIST EN 15182-3:2019は、消火活動における重要な規範を提供するものであり、特に消防用分岐管に関する期待される安全性と性能基準を明確に示している点で、その関連性は非常に高いといえます。業界の実務者にとって、この標準は効率的かつ安全な消火操作を実現するための基礎となるでしょう。
SIST EN 15182-3:2019은 소화펌프에서 공급된 소화제를 투사하는 휴대용 장비에 관한 표준으로, 손잡이가 있는 분사기구를 위한 문서의 제3부로, 부드러운 보어 제트 및 고정 스프레이 각도가 있는 분사기구에 대한 요구사항을 정의합니다. 이 표준의 범위는 EN 15182-1:2019에서 제공되는 요구사항에 추가하여, 명목 압력 16바(PN 16)를 가진 손잡이 분사기구와 최대 유량 1,000 l/min를 기준 압력 6바(0.6 MPa)에서 다루고 있습니다. 이 표준의 주요 강점 중 하나는 안전 요구사항, 성능 요구사항, 시험 방법을 포괄적으로 다룬다는 것입니다. 특히, 분사기구는 고위험 소방 상황에서 사용하지 말아야 하며, 최소 스프레이 각도가 30도 이하일 경우에는 소방관에 대한 보호가 inadequately 하다는 경고가 포함되어 있습니다. 이러한 명확한 지침은 관련 기준을 준수하는 장비를 개발하는 데 중요한 역할을 하며, 실질적인 안전성을 보장합니다. 또한, 전기 설치 근처의 화재를 진압할 때는 면허 받은 제조업체의 서면 승인이 필요하다는 점도 주목할 만합니다. 이는 전기 화재의 위험에 대한 인식을 높이고, 현장에서의 안전을 강화하는 데 기여합니다. 따라서 SIST EN 15182-3:2019 표준은 소방 서비스에서 휴대용 장비의 효과적이고 안전한 사용을 위한 중요한 기준을 제공합니다. 결론적으로, SIST EN 15182-3:2019 표준은 소방업계에서의 휴대용 분사기구의 안전성과 성능을 보장하기 위한 매우 관련 있는 문서이며, 고위험 상황에서의 책임 있는 사용을 위해 필수적으로 고려해야 할 요소들을 포함하고 있습니다.
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...