EN 1551:2000
(Main)Safety of industrial trucks - Self propelled trucks over 10 000 kg capacity
- BACK
- 18-Apr-2000
- 21-Aug-2012
- 53.060
- 98/37/EC
- M/BC/CEN/91/1
- CEN/TC 150
Safety of industrial trucks - Self propelled trucks over 10 000 kg capacity
This standard applies to self propelled lift trucks, the rated capacity of whic h exceeds 10000kg. This standard does not cover: Trucks powered by natural gas, trucks operated by remote control, trucks with elevating operator position.
Sicherheit von Flurförderzeugen - Kraftbetriebene Flurförderzeuge über 10 000 kg Tragfähigkeit
Diese Norm gilt für motorkraftbetriebene Flurförderzeuge mit einer Tragfähigkeit über 10000 kg. Diese Europäische Norm gilt nicht für: Flurförderzeuge, die mit Erdgas betrieben werden, Flurförderzeuge mit Fernsteuerung, Flurförderzeuge mit hebbarem Fahrerplatz.
Sécurité des chariots de manutention - Chariots automoteurs Plus de 10 000 kg
La présente norme concerne les chariots élévateurs automoteurs dont la capacité nominale est supérieure à 10 000 kg. La présente ne couvre pas: les chariots fonctionnant au gaz naturel, les chariots actionnés par télécommande, les chariots à poste de conduite élevable.
Varnost strojev - Vozila za talni transport - Motorna vozila z nosilnostjo več kot 10000 kg
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2002
9DUQRVWVWURMHY9R]LOD]DWDOQLWUDQVSRUW0RWRUQDYR]LOD]QRVLOQRVWMRYHþNRW
NJ
Safety of industrial trucks - Self propelled trucks over 10 000 kg capacity
Sicherheit von Flurförderzeugen - Kraftbetriebene Flurförderzeuge über 10 000 kg
Tragfähigkeit
Sécurité des chariots de manutention - Chariots automoteurs Plus de 10 000 kg
Ta slovenski standard je istoveten z: EN 1551:2000
ICS:
53.060 Industrijski tovornjaki Industrial trucks
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
SIST EN 1551:200
...
This May Also Interest You
This document is applicable to self-propelled and pedestrian propelled manual and semi-manual industrial trucks as defined in ISO 5053-1:2020 including their load handling devices and attachments (hereafter referred to as trucks) intended for use in potentially explosive atmospheres.
NOTE 1 Attachments mounted on the load carrier or on fork arms which are removable by the user are not considered to be a part of the truck.
This document specifies supplementary technical requirements for the prevention of the ignition of an explosive atmosphere of flammable gases, vapours, mists or dusts by industrial trucks of equipment group II and equipment category 2G, 3G, 2D or 3D.
NOTE 2 The relationship between an equipment category (hereafter referred to as category) and the corresponding zone (area classification) is shown in informative Annex B.
This document does not apply to:
- trucks of equipment group I;
- trucks of equipment group II, equipment category 1;
- trucks intended for use in potentially explosive atmospheres with hybrid mixtures;
- protective systems.
This document does not apply to trucks intended for use in potentially explosive atmospheres of carbon disulfide (CS2), carbon monoxide (CO) and/or ethylene oxide (C2H4O) due to the special properties of these gases.
Technical requirements relating to lithium-ion batteries and fuel cells as energy sources are not given in this document due to their specific hazards.
- Standard54 pagesEnglish languagesale 10% offe-Library read for×1 day
- 09-Jan-2024
- 53.060
- 2014/34/EU
- M/BC/CEN/92/46
- CEN/TC 150
This document specifies requirements for the types of industrial trucks specified in the scope of EN ISO 3691-5:2015.
This document is intended to be used in conjunction with EN ISO 3691-5:2015.
This document deals with the following significant hazards, hazardous situations or hazardous events relevant to pedestrian-propelled trucks, when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer:
- protection against crushing, shearing and trapping;
- electrical requirements;
- electromagnetic immunity.
These requirements are supplementary to those stated in EN ISO 3691-5:2015 with the addition of requirements for the following hazard:
- electromagnetic immunity (external radiation).
This document partially replaces the following requirement of EN ISO 3691-5:2015:
- electrical requirements.
This document specifies supplementary requirements to EN ISO 3691-5:2015:
- protection against crushing, shearing and trapping;
- information for use (instruction handbook and marking).
This document does not specify supplementary requirements to EN ISO 3691-5:2015:
- static electricity;
- radiation;
- general principles for the drafting of instructions;
- sales literature.
Annex A (informative) contains the list of significant hazards covered by this document.
- Standard14 pagesEnglish languagesale 10% offe-Library read for×1 day
- 19-Dec-2023
- 53.060
- 2006/42/EC
- M/396
- CEN/TC 150
This document specifies safety requirements and the means for their verification for driverless industrial trucks (hereafter referred to as trucks) and their systems.
Examples of driverless industrial trucks (trucks as defined in ISO 5053‑1:2020) include: “automated guided vehicle”, “autonomous mobile robot”, “bots”, “automated guided cart”, “tunnel tugger”, “under cart”, etc.
This document is also applicable to driverless industrial trucks which are provided with:
— automatic modes which either require operators’ action(s) to initiate or enable such automatic operations;
— the capability to transport one or more riders (which are neither considered as drivers nor as operators);
— additional manual modes which allow operators to operate the truck manually; or
— a maintenance mode which allows manual operation of truck functions for maintenance reasons.
This document is not applicable to trucks solely guided by mechanical means (rails, guides, etc.) or to remotely-controlled trucks, which are not considered to be driverless trucks.
For the purposes of this document, a driverless industrial truck is a powered truck, which is designed to operate automatically. A driverless truck system comprises the control system, which can be part of the truck and/or separate from it, guidance means and power system. Requirements for power sources are not covered in this document.
The condition of the operating zone has a significant effect on the safe operation of the driverless industrial truck. The preparations of the operating zone to eliminate the associated hazards are specified in Annex A.
This document is applicable to all significant hazards, hazardous situations or hazardous events during all phases of the life of the truck (ISO 12100:2010, 5.4), as listed in Annex B, relevant to the applicable machines when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
In particular, this document does not apply to significant hazards related to:
— noise;
— vibrations;
— ionising and non-ionising radiation;
— laser radiation;
— sales literature (commercial documents);
— declaration of vibrations transmitted by mobile machinery.
It does not apply to additional hazards that can occur:
— during operation in severe conditions (e.g. extreme climates, freezer applications, strong magnetic fields);
— during operation in nuclear environments;
— from trucks intended to operate in public zones (see in particular ISO 13482:2014);
— during operation on a public road;
— during operation in potentially explosive environments;
— during operation in military applications;
— during operation with specific hygienic requirements;
— during operation in ionizing radiation environments;
— during the transportation of (a) person(s) other than (the) intended rider(s);
— when handling loads the nature of which can lead to dangerous situations (e.g. molten metals, acids/bases, radiating materials);
— for rider positions with elevation function higher than 1 200 mm from the floor/ground to the platform floor.
This document does not contain safety requirements for trailer(s) being towed behind a truck.
This document does not contain safety requirements for elevated operator trucks.
This document does not apply to trucks manufactured before the date of its publication.
- Standard87 pagesEnglish languagesale 10% offe-Library read for×1 day
- 18-Jul-2023
- 53.060
- 2006/42/EC
- M/396
- CEN/TC 150
This document specifies requirements for the types of industrial trucks specified in the scope of EN ISO 3691-2:2023.
This document is intended to be used in conjunction with EN ISO 3691 2:2023. These requirements are supplementary to those stated in EN ISO 3691-2:2023.
This document deals with the following supplementary requirements and significant hazards, hazardous situations or hazardous events relevant, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer:
- electrical requirements;
- noise emissions;
- vibration;
- electromagnetic radiation.
This document specifies supplementary requirements to EN ISO 3691-2:2023:
- operator's seat;
- protection against crushing, shearing and trapping;
- longitudinal stability determination;
- visibility;
- information for use (instruction handbook and marking).
Annex A (informative) contains the list of significant hazards covered by this document.
- Standard12 pagesEnglish languagesale 10% offe-Library read for×1 day
- 28-Feb-2023
- 53.060
- CEN/TC 150
2021-07-26 JF: Through decision 429/2021 taken on 2021-07-08, TC decided to decouple the WI from the EU legislation
- Amendment11 pagesEnglish languagesale 10% offe-Library read for×1 day
- 28-Feb-2023
- 53.060
- 2006/42/EC
- M/396
- CEN/TC 150
This document specifies requirements for the types of industrial trucks specified in the scope of EN ISO 3691-3:2016.
This document is intended to be used in conjunction with EN ISO 3691-3:2016. These requirements are supplementary to those stated in EN ISO 3691-3:2016.
This document deals with the following significant hazards, hazardous situations or hazardous events relevant when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer:
- acceleration, deceleration (kinetic energy);
- machinery mobility.
This document specifies supplementary requirements to EN ISO 3691-1:2015, EN ISO 3691-3:2016 and EN 16307-1:2020:
- brakes operation without guidance system;
- operator fall protection;
- information for use (instruction handbook and marking).
Annex A (informative) contains the list of significant hazards covered by this document.
- Standard9 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft11 pagesEnglish languagesale 10% offe-Library read for×1 day
- 28-Feb-2023
- 53.060
- 2006/42/EC
- M/396
- CEN/TC 150
This document gives safety requirements and the means for their verification for self-propelled industrial variable-reach trucks and variable-reach container handlers/reach stackers as defined in ISO 5053‑1 (hereafter referred to as trucks), equipped with forks or integral load-handling devices for normal industrial duties (e.g. fork arms or means, such as spreaders, for handling containers).
This document does not apply to:
— rough-terrain variable-reach trucks,
— rough-terrain variable-reach trucks for handling containers,
— lorry mounted trucks covered by ISO 20297-1,
— machines designed primarily for earth-moving (e.g. loaders and dozers), even when their buckets and blades are replaced with forks,
— machines from which the load can swing freely in all directions.
This document is not applicable to trucks manufactured before the date of its publication.
For the purposes of this document, fork arms and integrated attachments are considered to be a part of the truck, whereas attachments/equipment/tools mounted on the load carrier or on the fork arms which are removable by the user are not. Nevertheless, for interchangeable equipment, which is assembled with the truck by the operator in order to change the function of, or attribute a new function to, the truck, this document does provide requirements for:
— the interface with the truck,
— protection of the operator in the normal operating position from crushing and shearing hazards,
— operating and maintenance instructions,
— load charts,
— marking,
— provision for transportation, and,
— indicator lights for attachments for lifting containers
Any regional requirements additional to the provisions of this document are addressed in EN 16307-2:2023 and ISO/TS 3691‑8.
This document deals with all significant hazards, hazardous situations or hazardous events, as listed in Annex B, with the exception of the following, relevant to the applicable machines when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
It does not establish requirements for hazards that can occur:
— during construction;
— when using trucks on public roads;
— when operating in potentially explosive atmospheres;
— when lifting persons; or
— during dismantling, disabling and scrapping.
This document does not provide requirements for:
— tools, lifting accessories or removeable attachments, which do not change the function or attribute a new function, mounted on the load carrier or fork arms;
— attachments/equipment mounted on the load carrier or on the fork arms which are removable by the user and which change the function or attribute a new function, except as stated above;
— the reliability of control systems and performance requirements for safety related parts of control systems; or
— the requirement for fitting an enclosed cab, whether pressurized or not.
- Standard55 pagesEnglish languagesale 10% offe-Library read for×1 day
- 28-Feb-2023
- 53.060
- 2006/42/EC
- M/396
- CEN/TC 150
This document applies to pedestrian propelled industrial platform trucks as defined in 3.1 with a rated capacity up to and including 500 kg, hereinafter referred to as “trucks” and designed for general purposes.
This document does not apply to:
— shopping trolleys referred to in EN 1929, Parts 1 to 4 and 7 (CEN/TC 291);
— roll containers referred to in EN 12674, Parts 1 to 4 (CEN/TC 261);
— trucks that are intended to be towed by powered vehicles, e.g. milk-run-trains/trailer trains/tugger trains.
This document deals with the technical requirements to minimize the hazards listed in Annex C which can arise during commissioning, operation and maintenance of trucks when carried out in accordance with the specifications as intended by the manufacturer.
This document does not specify the additional requirements for:
— operation in severe conditions (e.g. extreme environmental conditions such as: freezer applications, high temperatures, corrosive environment);
— operation subject to special rules (e.g. potentially explosive atmospheres);
— handling of loads the nature of which could lead to dangerous situations (e.g. molten metal, acids/alkalis, radiating materials, especially brittle loads);
— hazards occurring during construction, transportation, decommissioning and disposal;
— direct contact with foodstuffs;
— operation on gradients or on surfaces other than smooth, level, hard surfaces;
— trucks designed for special applications (e.g., trucks used in hospitals as dinner trollies);
— trucks fitted with hinged or sliding doors.
Other possible limitations of the scope of other standards referred to that also apply to this document.
Hazards relating to noise, vibration, visibility and static electricity are not dealt with in this document.
This document applies to trucks manufactured after the date of issue.
- Standard23 pagesEnglish languagesale 10% offe-Library read for×1 day
- 10-May-2022
- 29-Nov-2022
- 53.060
- CEN/TC 150
This document gives safety requirements and the means for their verification for self-propelled carriers designed for carrying burdens without lifting, as defined in ISO 5053‑1:2020, and/or personnel carriers, having three or more wheels, a maximum speed not exceeding 56 km/h and a load capacity not exceeding 5 000 kg (hereafter referred to as carriers or trucks).
This document is applicable to trucks equipped with a platform (which can be tilting) for the purpose of carrying materials or with a number of seats for the purpose of transporting passengers.
It is not applicable to:
— vehicles intended primarily for earth-moving or over-the-road hauling;
— driverless trucks;
— pedestrian controlled trucks;
— golf cars;
— tractors with a drawbar pull up to and including 20 000 N equipped with a platform for the purpose of carrying materials.
This document deals with all significant hazards, hazardous situations or hazardous events, as listed in Annex A, relevant to the applicable machines when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
This document does not deal with hazard due to the risk of break-up during operation.
It does not establish requirements for hazards that can occur when using trucks on public roads or when operating in potentially explosive atmospheres.
It does not establish requirements to provide fire extinguishers.
Regional requirements, additional to the requirements given in this document, are addressed in EN 16307‑6:2014 and ISO/TS 3691‑8:2019.
- Standard39 pagesEnglish languagesale 10% offe-Library read for×1 day
- 26-Oct-2021
- 29-Apr-2022
- 53.060
- 2006/42/EC
- M/396
- CEN/TC 150
This document applies to slewing rough-terrain variable-reach trucks (hereinafter referred to as trucks) as defined in ISO 5053-1:2020, 3.22, that have a specific seated operator’s position, on the left-hand side of the boom, or centre position (excluding operator position on the right side of the boom).
This document specifies a static test method for determining and evaluating the operator’s visibility on a rectangular boundary close around the truck and on a 12 m visibility test circle. Performance requirements for visibility are specified in this document. A calculation method or computer simulation can also be used.
This document does not provide performance requirements for the additional means for indirect visibility.
This document also covers information to be provided by the manufacturer.
- Standard32 pagesEnglish languagesale 10% offe-Library read for×1 day
- 28-Sep-2021
- 30-Mar-2022
- 53.060
- 2006/42/EC
- M/396
- CEN/TC 150
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.