EN 1807:1999/prA1

Safety of woodworking machines - Band sawing machines

Replace the first paragraph with the following:
"This document deals with the significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to stationary and displaceable band sawing machines with either manual or automatic loading and/or unloading, hereinafter referred to as "machines" designed to cut solid wood, chipboard, fibreboard, plywood and also these materials where they are covered with plastic laminate or edgings.".
Delete the second paragraph.
Delete the first sentence of the third paragraph.
Replace in the fourth paragraph the first indent with:
"hand held motor-operated electric tools or any adaptation permitting their use in a different mode, i.e. bench mounting;".
Add a note: "NOTE 1   Hand-held motor operated electric tools are covered by the requirements of
EN 60745-1:2006 together with EN 60745-2-20:2003.".
Replace in the fourth paragraph the second indent with the following:
"transportable machines set up on a bench or a table similar to a bench, which are intended to carry out work in a stationary position, capable of being lifted by one person by hand.".
Add a note: "NOTE 2   Transportable electrically driven machines are covered by the requirements of EN 61029-1:2000 together with EN 61029-2-5:2002.".

Sicherheit von Holzbearbeitungsmaschinen - Bandsägemaschinen

Sécurité des machines pour le travail du bois - Machines à scier à ruban

Varnost lesnoobdelovalnih strojev - Tračne žage

General Information

• Status: Not Published
• ICS: 79.120.10 - Woodworking machines
• Technical Committee: CEN/TC 142 - Woodworking machines - Safety
• Drafting Committee: CEN/TC 142/WG 3 - Bandsawing machines
• Current Stage: 5060 - Closure of Vote - Formal Approval
• Start Date: 29-Jun-2009
• Completion Date: 29-Jun-2009
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Directive: 98/37/EC - Machinery
• Mandate: M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: SIST EN 1807:2000/kprA1:2009 - Safety of woodworking machines - Band sawing machines

Relations

• Merged Into: EN 1807:1999+A1:2009 - Safety of woodworking machines - Band sawing machines
• Effective Date: 19-Jan-2023
• Amends: EN 1807:1999 - Safety of woodworking machines - Band sawing machines
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
01-maj-2009
9DUQRVWOHVQRREGHORYDOQLKVWURMHY7UDþQHåDJH
Safety of woodworking machines - Band sawing machines
Sicherheit von Holzbearbeitungsmaschinen - Bandsägemaschinen
Sécurité des machines pour le travail du bois - Machines à scier à ruban
Ta slovenski standard je istoveten z: EN 1807:1999/prA1
ICS:
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
FINAL DRAFT
EN 1807:1999
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
January 2009
ICS 79.120.10
English Version
Safety of woodworking machines - Band sawing machines
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungsmaschinen -
scier à ruban Bandsägemaschinen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 142.
This draft amendment A1, if approved, will modify the European Standard EN 1807:1999. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
: This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
Warning
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1807:1999/prA1:2009: E
worldwide for CEN national Members.

Contents Page
Foreword .3
1 Modification to the Foreword .4
2 Modification to Clause 1, Scope .4
3 Modification to Clause 2, Normative references .4
4 Modification to 3.1, Definitions .6
5 Modification to Clause 4, List of hazards .6
6 Modification to Clause 5, Safety requirements and/or measures (hanging paragraph) .9
7 Modification to 5.1.1, Safety and reliability of control systems .9
8 Modification to 5.1.3, Starting .9
9 Modification to 5.1.4.1, All machines .9
10 Modification to 5.1.5, Emergency stop .9
11 Modification to 5.1.8, Control duplication .9
12 Modification to 5.1.9, Failure of the power supply .9
13 Modification to 5.2.1, Stability .9
14 Modification to 5.2.2.1, Characteristics of guards . 10
15 Modification to 5.3.1, Fire/explosion . 10
16 Modification to 5.3.2.2, Noise emission measurement . 10
17 Modification to 5.3.2.3, Declaration . 10
18 Modification to 5.3.4, Electricity . 11
19 Modification to 5.3.5, Ergonomics and handling . 11
20 Modification to 5.3.6, Lighting . 11
21 Modification to 5.3.12, Laser . 12
22 Modification to 5.3.15, Isolation . 12
23 Modification to 5.3.16, Maintenance . 12
24 Modification to 6.1, Warning devices. 12
25 Modification to 6.2, Marking of the machine . 12
26 Modification to 6.3, Instruction handbook . 13
27 Modification to Annex A . 17
28 Modification to Annex ZA . 17
A29 Addition of Annex ZB . 18

Foreword
This document (EN 1807:1999/prA1:2009) has been prepared by Technical Committee CEN/TC 142
“Woodworking machines - Safety”, the secretariat of which is held by UNI.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of the Machinery Directive and Out
door Noise Directive.
For relationship with EU Directive, see informative Annexes ZA and ZB, which are integral parts of this
document.
1 Modification to the Foreword
Replace the fourth paragraph with the following:
"For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.".
2 Modification to Clause 1, Scope
Replace the first paragraph with the following:
"This document deals with the significant hazards, hazardous situations and events as listed in Clause 4
which are relevant to stationary and displaceable band sawing machines with either manual or automatic
loading and/or unloading, hereinafter referred to as “machines” designed to cut solid wood, chipboard,
fibreboard, plywood and also these materials where they are covered with plastic laminate or edgings.".
Delete the second paragraph.
Delete the first sentence of the third paragraph.
Replace in the fourth paragraph the first indent with:
"hand held motor-operated electric tools or any adaptation permitting their use in a different mode, i.e. bench
mounting;".
Add a note: "NOTE 1 Hand-held motor operated electric tools are covered by the requirements of
EN 60745-1:2006 together with EN 60745-2-20:2003.".
Replace in the fourth paragraph the second indent with the following:
"transportable machines set up on a bench or a table similar to a bench, which are intended to carry out work
in a stationary position, capable of being lifted by one person by hand.".
Add a note: "NOTE 2 Transportable electrically driven machines are covered by the requirements of EN 61029-1:2000
together with EN 61029-2-5:2002.".
3 Modification to Clause 2, Normative references
Replace the standard paragraph with the following: "The following referenced documents are indispensable
for the application of this document. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.".
Delete reference EN 292-1:1991 in Clause 2 and replace "EN 292-1:1991" with "EN ISO 12100-1:2003"
throughout the document.
Delete references EN 292-2:1991 and EN 292/A1:1995.
Delete the reference to EN 294:1992 and add "EN ISO 13857:2008, Safety of machinery — Safety distances
to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)" and replace
"EN 294:1992" with "EN ISO 13857:2008" throughout the document.
Replace "EN 349:1992" with "EN 349:1993" throughout the document.
Delete reference to EN 418:1992 and add: "EN ISO 13850:2008, Safety of machinery — Emergency stop —
st
Principles for design (ISO 13850:2006)" and replace "EN 418:1992" in 5.1.5, 1 paragraph, with
"EN ISO 13850".
Replace "EN 60204-1:1992" with "EN 60204-1:2006" and replace in the title
"(IEC 204:1992, modified)" with "(IEC 60204-1:2005, modified)".
Replace "EN 60825-1:1994" with "EN 60825-1:2007" and replace in the title
"(IEC 60825:1993)" with "(IEC 60825:2007).
Replace "EN 60947-4-1:1992" with "EN 60947-4-1:2001" throughout the document and replace in the title
"(IEC 947-4-1:1990)" with "(IEC 60947-4-1:2000)".
Replace "EN 60947-5-1:1991" with "EN 60947-5-1:2004" throughout the document and replace in the title
"(IEC 947-5-1:1990)" with "(IEC 60947-5-1:2003)".
Replace "EN 61029:1995" with "EN 61029-1:2000" throughout the document and replace in the title
"(IEC 1029-1:1990 modified)" with "(IEC 61029-1:1990, modified)".
Replace reference to prEN 60129-2-5 with "EN 61029-2-5:2002, Safety of transportable motor-operated
electric tools — Part 2: Particular requirements for band saws (IEC 61029-2-5:1993+A1:2001, modified)".
Replace "prEN 61496-2" with "CLC/TS 61496-2:2006" in Clause 2 and "prEN 61496-2" with
rd
"CLC/TS 61496-2" throughout the document and the 3 element of the title with "Part 2: Particular
requirements for equipment using active opto-electronic protective devices (AOPDs) (IEC 61496-2:2006)".
Delete reference to ISO 3745:1997 and add: "EN ISO 3745:2003, Acoustics — Determination of sound power
levels of noise sources using sound pressure — Precision methods for anechoic and semi-anechoic rooms
(ISO 3745:2003)" and replace "ISO 3745:1977" with "EN ISO 3745:2003" throughout the document.
Replace reference to HD 21.1 S3:1997 with "HD 21.1 S4:2002, Cables of rated voltages up to and including
450/750 V and having thermoplastic insulation — Part 1: General requirements" and replace
"HD 21.1 S3:1997" with "HD 21.1 S4:2002" throughout the document.
Replace reference to HD 22.1 S3:1997 with "HD 22.1 S4:2002, Cables of rated voltages up to and including
450/750 V and having cross-linked insulation — Part 1: General requirements" and replace
"HD 22.1 S3:1997" with "HD 22.1 S4:2002" throughout the document.
Replace reference to prEN 1760-1 with "EN 1760-1:1997, Safety of machinery — Pressure sensitive
protective devices — Part 1: General principles for the design and testing of pressure sensitive mats and
pressure sensitive floors".
Delete reference to ISO/TR 11688-1:1995 and add: "EN ISO 11688-1:1998, Acoustics — Recommended
practice for the design of low-noise machinery and equipment — Part 1: Planning (ISO/TR 11688-1:1995)"
and replace "ISO/TR 11688-1:1995" with "EN ISO 11688-1:1998" throughout the text.
Replace reference to ISO 1940-1:1986 with "ISO 1940-1:2003, Mechanical vibration — Balance quality
requirements for rotors in a constant (rigid) state — Part 1: Specification and verification of balance
tolerances" and replace "ISO 1940-1:1986" with "ISO 1940-1:2003" throughout the text
Add the following references:
"EN 614-1:2006, Safety of machinery — Ergonomic design principles — Part 1: Terminology and general
principles",
"EN 894-1:1997, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 1: General principles for human interactions with displays and control actuators
EN 894-2:1997, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 2: Displays
EN 894-3:2000, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 3: Control actuators",
"EN 1005-1:2001, Safety of machinery — Human physical performance — Part 1: Terms and definitions
EN 1005-2:2003, Safety of machinery — Human physical performance — Part 2: Manual handling of
machinery and component parts of machinery
EN 1005-3:2002, Safety of machinery — Human physical performance — Part 3: Recommended force limits
for machinery operation
EN 1005-4:2005, Safety of machinery — Human physical performance — Part 4: Evaluation of working
postures and movements in relation to machinery
EN 1037:1995, Safety of machinery — Prevention of unexpected start-up",
EN ISO 4871:1996, Acoustics — Declaration and verification of noise emission values of machinery and
equipment (ISO 4871:1996)" and
"EN ISO 12100-1:2003, Safety of machinery — Basic co
...