SIST EN 1807:2000/kprA1:2009
(Amendment)Safety of woodworking machines - Band sawing machines
Safety of woodworking machines - Band sawing machines
Replace the first paragraph with the following:
"This document deals with the significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to stationary and displaceable band sawing machines with either manual or automatic loading and/or unloading, hereinafter referred to as "machines" designed to cut solid wood, chipboard, fibreboard, plywood and also these materials where they are covered with plastic laminate or edgings.".
Delete the second paragraph.
Delete the first sentence of the third paragraph.
Replace in the fourth paragraph the first indent with:
"hand held motor-operated electric tools or any adaptation permitting their use in a different mode, i.e. bench mounting;".
Add a note: "NOTE 1 Hand-held motor operated electric tools are covered by the requirements of
EN 60745-1:2006 together with EN 60745-2-20:2003.".
Replace in the fourth paragraph the second indent with the following:
"transportable machines set up on a bench or a table similar to a bench, which are intended to carry out work in a stationary position, capable of being lifted by one person by hand.".
Add a note: "NOTE 2 Transportable electrically driven machines are covered by the requirements of EN 61029-1:2000 together with EN 61029-2-5:2002.".
Sicherheit von Holzbearbeitungsmaschinen - Bandsägemaschinen
Sécurité des machines pour le travail du bois - Machines à scier à ruban
Varnost lesnoobdelovalnih strojev - Tračne žage
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 1807:2000/kprA1:2009
01-maj-2009
9DUQRVWOHVQRREGHORYDOQLKVWURMHY7UDþQHåDJH
Safety of woodworking machines - Band sawing machines
Sicherheit von Holzbearbeitungsmaschinen - Bandsägemaschinen
Sécurité des machines pour le travail du bois - Machines à scier à ruban
Ta slovenski standard je istoveten z: EN 1807:1999/prA1
ICS:
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN 1807:2000/kprA1:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 1807:2000/kprA1:2009
---------------------- Page: 2 ----------------------
SIST EN 1807:2000/kprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 1807:1999
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
January 2009
ICS 79.120.10
English Version
Safety of woodworking machines - Band sawing machines
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungsmaschinen -
scier à ruban Bandsägemaschinen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 142.
This draft amendment A1, if approved, will modify the European Standard EN 1807:1999. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
: This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
Warning
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1807:1999/prA1:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 1807:2000/kprA1:2009
EN 1807:1999/prA1:2009 (E)
Contents Page
Foreword .3
1 Modification to the Foreword .4
2 Modification to Clause 1, Scope .4
3 Modification to Clause 2, Normative references .4
4 Modification to 3.1, Definitions .6
5 Modification to Clause 4, List of hazards .6
6 Modification to Clause 5, Safety requirements and/or measures (hanging paragraph) .9
7 Modification to 5.1.1, Safety and reliability of control systems .9
8 Modification to 5.1.3, Starting .9
9 Modification to 5.1.4.1, All machines .9
10 Modification to 5.1.5, Emergency stop .9
11 Modification to 5.1.8, Control duplication .9
12 Modification to 5.1.9, Failure of the power supply .9
13 Modification to 5.2.1, Stability .9
14 Modification to 5.2.2.1, Characteristics of guards . 10
15 Modification to 5.3.1, Fire/explosion . 10
16 Modification to 5.3.2.2, Noise emission measurement . 10
17 Modification to 5.3.2.3, Declaration . 10
18 Modification to 5.3.4, Electricity . 11
19 Modification to 5.3.5, Ergonomics and handling . 11
20 Modification to 5.3.6, Lighting . 11
21 Modification to 5.3.12, Laser . 12
22 Modification to 5.3.15, Isolation . 12
23 Modification to 5.3.16, Maintenance . 12
24 Modification to 6.1, Warning devices. 12
25 Modification to 6.2, Marking of the machine . 12
26 Modification to 6.3, Instruction handbook . 13
27 Modification to Annex A . 17
28 Modification to Annex ZA . 17
A29 Addition of Annex ZB . 18
2
---------------------- Page: 4 ----------------------
SIST EN 1807:2000/kprA1:2009
EN 1807:1999/prA1:2009 (E)
Foreword
This document (EN 1807:1999/prA1:2009) has been prepared by Technical Committee CEN/TC 142
“Woodworking machines - Safety”, the secretariat of which is held by UNI.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of the Machinery Directive and Out
door Noise Directive.
For relationship with EU Directive, see informative Annexes ZA and ZB, which are integral parts of this
document.
3
---------------------- Page: 5 ----------------------
SIST EN 1807:2000/kprA1:2009
EN 1807:1999/prA1:2009 (E)
1 Modification to the Foreword
Replace the fourth paragraph with the following:
"For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.".
2 Modification to Clause 1, Scope
Replace the first paragraph with the following:
"This document deals with the significant hazards, hazardous situations and events as listed in Clause 4
which are relevant to stationary and displaceable band sawing machines with either manual or automatic
loading and/or unloading, hereinafter referred to as “machines” designed to cut solid wood, chipboard,
fibreboard, plywood and also these materials where they are covered with plastic laminate or edgings.".
Delete the second paragraph.
Delete the first sentence of the third paragraph.
Replace in the fourth paragraph the first indent with:
"hand held motor-operated electric tools or any adaptation permitting their use in a different mode, i.e. bench
mounting;".
Add a note: "NOTE 1 Hand-held motor operated electric tools are covered by the requirements of
EN 60745-1:2006 together with EN 60745-2-20:2003.".
Replace in the fourth paragraph the second indent with the following:
"transportable machines set up on a bench or a table similar to a bench, which are intended to carry out work
in a stationary position, capable of being lifted by one person by hand.".
Add a note: "NOTE 2 Transportable electrically driven machines are covered by the requirements of EN 61029-1:2000
together with EN 61029-2-5:2002.".
3 Modification to Clause 2, Normative references
Replace the standard paragraph with the following: "The following referenced documents are indispensable
for the application of this document. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.".
Delete reference EN 292-1:1991 in Clause 2 and replace "EN 292-1:1991" with "EN ISO 12100-1:2003"
throughout the document.
Delete references EN 292-2:1991 and EN 292/A1:1995.
Delete the reference to EN 294:1992 and add "EN ISO 13857:2008, Safety of machinery — Safety distances
to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)" and replace
"EN 294:1992" with "EN ISO 13857:2008" throughout the document.
Replace "EN 349:1992" with "EN 349:1993" throughout the document.
4
---------------------- Page: 6 ----------------------
SIST EN 1807:2000/kprA1:2009
EN 1807:1999/prA1:2009 (E)
Delete reference to EN 418:1992 and add: "EN ISO 13850:2008, Safety of machinery — Emergency stop —
st
Principles for design (ISO 13850:2006)" and replace "EN 418:1992" in 5.1.5, 1 paragraph, with
"EN ISO 13850".
Replace "EN 60204-1:1992" with "EN 60204-1:2006" and replace in the title
"(IEC 204:1992, modified)" with "(IEC 60204-1:2005, modified)".
Replace "EN 60825-1:1994" with "EN 60825-1:2007" and replace in the title
"(IEC 60825:1993)" with "(IEC 60825:2007).
Replace "EN 60947-4-1:1992" with "EN 60947-4-1:2001" throughout the document and replace in the title
"(IEC 947-4-1:1990)" with "(IEC 60947-4-1:2000)".
Replace "EN 60947-5-1:1991" with "EN 60947-5-1:2004" throughout the document and replace in the title
"(IEC 947-5-1:1990)" with "(IEC 60947-5-1:2003)".
Replace "EN 61029:1995" with "EN 61029-1:2000" throughout the document and replace in the title
"(IEC 1029-1:1990 modified)" with "(IEC 61029-1:1990, modified)".
Replace reference to prEN 60129-2-5 with "EN 61029-2-5:2002, Safety of transportable motor-operated
electric tools — Part 2: Particular requirements for band saws (IEC 61029-2-5:1993+A1:2001, modified)".
Replace "prEN 61496-2" with "CLC/TS 61496-2:2006" in Clause 2 and "prEN 61496-2" with
rd
"CLC/TS 61496-2" throughout the document and the 3 element of the title with "Part 2: Particular
requirements for equipment using active opto-electronic protective devices (AOPDs) (IEC 61496-2:2006)".
Delete reference to ISO 3745:1997 and add: "EN ISO 3745:2003, Acoustics — Determination of sound power
levels of noise sources using sound pressure — Precision methods for anechoic and semi-anechoic rooms
(ISO 3745:2003)" and replace "ISO 3745:1977" with "EN ISO 3745:2003" throughout the document.
Replace reference to HD 21.1 S3:1997 with "HD 21.1 S4:2002, Cables of rated voltages up to and including
450/750 V and having thermoplastic insulation — Part 1: General requirements" and replace
"HD 21.1 S3:1997" with "HD 21.1 S4:2002" throughout the document.
Replace reference to HD 22.1 S3:1997 with "HD 22.1 S4:2002, Cables of rated voltages up to and including
450/750 V and having cross-linked insulation — Part 1: General requirements" and replace
"HD 22.1 S3:1997" with "HD 22.1 S4:2002" throughout the document.
Replace reference to prEN 1760-1 with "EN 1760-1:1997, Safety of machinery — Pressure sensitive
protective devices — Part 1: General principles for the design and testing of pressure sensitive mats and
pressure sensitive floors".
Delete reference to ISO/TR 11688-1:1995 and add: "EN ISO 11688-1:1998, Acoustics — Recommended
practice for the design of low-noise machinery and equipment — Part 1: Planning (ISO/TR 11688-1:1995)"
and replace "ISO/TR 11688-1:1995" with "EN ISO 11688-1:1998" throughout the text.
Replace reference to ISO 1940-1:1986 with "ISO 1940-1:2003, Mechanical vibration — Balance quality
requirements for rotors in a constant (rigid) state — Part 1: Specification and verification of balance
tolerances" and replace "ISO 1940-1:1986" with "ISO 1940-1:2003" throughout the text
Add the following references:
"EN 614-1:2006, Safety of machinery — Ergonomic design principles — Part 1: Terminology and general
principles",
"EN 894-1:1997, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 1: General principles for human interactions with displays and control actuators
5
---------------------- Page: 7 ----------------------
SIST EN 1807:2000/kprA1:2009
EN 1807:1999/prA1:2009 (E)
EN 894-2:1997, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 2: Displays
EN 894-3:2000, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 3: Control actuators",
"EN 1005-1:2001, Safety of machinery — Human physical performance — Part 1: Terms and definitions
EN 1005-2:2003, Safety of machinery — Human physical performance — Part 2: Manual handling of
machinery and component parts of machinery
EN 1005-3:2002, Safety of machinery — Human physical performance — Part 3: Recommended force limits
for machinery operation
EN 1005-4:2005, Safety of machinery — Human physical performance — Part 4: Evaluation of working
postures and movements in relation to machinery
EN 1037:1995, Safety of machinery — Prevention of unexpected start-up",
EN ISO 4871:1996, Acoustics — Declaration and verification of noise emission values of machinery and
equipment (ISO 4871:1996)" and
"EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic
terminology, methodology (ISO 12100-1:2003)
EN ISO 12100-2:2003, Safety of machinery — Basic concepts, general principles for design — Part 2:
Technical principles (ISO 12100-2:2003)".
4 Modification to 3.1, Definitions
Definition 3.1.20, replace the term with "displaceable machine".
Definition 3.1.22, replace the term with "information from the supplier".
5 Modification to Clause 4, List of hazards
Replace the title of Clause 4 with: "List of significant hazards".
Replace the clause content with:
"This clause contains the significant hazards, hazardous situations and events (see EN 1050:1996) as far as
they are dealt with in this document, identified by risk assessment as significant for the machines as defined in
the scope and which require action to eliminate or reduce the risk. This document deals with these significant
hazards by defining safety requirements and/or measures or by reference to relevant standards.
These hazards are listed in Table 1 in accordance with Annex A of EN 1050:1996.
6
---------------------- Page: 8 ----------------------
SIST EN 1807:2000/kprA1:2009
EN 1807:1999/prA1:2009 (E)
Table 1 — List of significant hazards
Hazards, hazardous situations and Relevant
No hazardous events EN ISO 12100 sub-clause
of this
document
Part 1: Part 2:
2003 2003
1 Mechanical hazards related to:
- machine parts or work-pieces:
a) shape; 4.2 4.2.1, 5.2.2,
4.2.2, 5 5.2.3.1,
5.2.6,
5.2.7.1.2,
5.2.7.2,
5.2.7.3,
5.2.8
b) relative location; 5.1.2, 5.1.4,
5.2.3.1,
5.2.3.2,
5.2.7.1.2,
5.2.7.4,
5.2.8, 5.2.9
c) mass and stability (potential energy of 5.2.5
elements which may move under the
effect of gravity);
d) mass and velocity (kinetic energy of 5.2.1,
elements in controlled or uncontrolled 5.2.7.1.2,
motion); 5.2.7.3
e) mechanical strength. 5.2.2.1,
5.2.6.2
- accumulation of energy inside the machinery:
f) elastic elements (springs), or 4.2 4.10, 5.5.4 5.2.6
g) liquids and gases under pressure; 4.2 4.10, 5.5.4 5.3.7, 5.3.8
1.1 Crushing hazard 4.2.1 5.2.9
1.2 Shearing hazard 5.2.8, 5.2.9
1.3 Cutting or severing hazard 5.2.7
1.4 Entanglement hazard 5.2.7, 5.2.8
1.5 Drawing-in or trapping hazard 5.2.7,
5.2.8, 5.2.9
1.6 Impact hazard 5.2.7
1.7 Stabbing or puncture hazard 5.2.2
1.9 High pressure fluid injection or ejection 5.3.7, 5.3.8
hazard
2 Electrical hazards due to:
2.1 Contact of persons with live parts (direct 4.3 4.9, 5.5.4 5.3.4,
contact) 5.3.15,
5.3.16
7
---------------------- Page: 9 ----------------------
SIST EN 1807:2000/kprA1:2009
EN 1807:1999/prA1:2009 (E)
2.2 Contact of persons with parts which 4.3 4.9 5.3.4,
have become live under faulty 5.3.15,
conditions (indirect contact) 5.3.16
4 Hazards generated by noise, resulting in:
Hearing loss (deafness), other 4.5 4.2.2, 5 5.3.2
4.1
physiological disorders (loss of balance,
loss of awareness)
Hazards generated by radiation
6
6.5 Lasers 4.7 5.3.12
7 Hazards generated by materials and substances (and their constituent elements)
processed or used by the machinery
7.1 Hazards from contact with or inhalation 4.8 4.3b, 4.4 5.3.3
of harmful fluids and dusts
7.2 Fire hazard 4.8 4.4 5.3.1
8 Hazards generated by neglecting ergonomic principles in machinery design
related to:
8.1 Unhealthy postures or excessive effort 4.9 4.7, 4.8.2, 5.1.2
4.11.12,
5.5.5, 5.5.6
8.2 Hand-arm or foot-leg anatomy 4.9 4.8.3 5.1.2
8.4 Local lighting 4.8.6 6.3
8.6 Human error, human behaviour 4.8, 4.11.8, 6.3
4.11.10,
5.5.2, 6
8.7 Design, location or identification of 4.8.7, 5.1.2
manual controls 4.11.8
8.8 Design or location of visual display units 4.8.8, 6.2 5.1.2
Unexpected start up, unexpected overrun/overspeed (or any similar malfunction)
10
from:
10.1 Failure/disorder of the control system 4.11, 5.5.4 5.1.1
10.2 Restoration of energy supply after an 4.11.4 5.1.1, 5.1.9
interruption
10.3 External influences on electrical 4.11.11 5.1.1
equipment
10.6 Errors made by the operator (due to 4.9 4.8, 4.11.8, 5.1.1, 5.3.5,
mismatch of machinery with human 4.11.10, 6.3
characteristics and abilities, see 8.6) 5.5.2, 6
5.1.2, 5.1.4,
11 Impossibility of stopping the machine 4.11.1,
5.2
in the best possible conditions 4.11.3,
5.5.2
5.1.9
13 Failure of the power supply 4.11.1,
4.11.4
5.1.1
14 Failure of the control circuit 4.11, 5.5.4
5.1.8
15 Errors of fitting 4.9 4.7, 6.5
5.2.2
16 Break-up during operation 4.2.2 4.3
5.2.2, 5.2.3,
17 Falling or ejected objects or fluids 4.2.2 4.3, 4.10
5.2.9
5.2.1
18 Loss of stability / overturning of 4.2.2 5.2.6
machinery
".
8
---------------------- Page: 10 ----------------------
SIST EN 1807:2000/kprA1:2009
EN 1807:1999/prA1:2009 (E)
6 Modification to Clause 5, Safety requirements and/or measures (hanging
paragraph)
Replace "3 of EN 292-2:1991" with "4.1 of EN ISO 12100-2:2003".
7 Modification to 5.1.1, Safety and reliability of control systems
Replace in the first paragraph the first sentence with: "For the purposes of this standard a safety related
control system is one from and including the initial manual control or position detector or sensor up to and
including the power control element of the final machine actuator, e.g. motor or brake.".
nd
In the 2 paragraph, b), replace "EN 60204-1:1992" twice with "EN 60204-1:2006".
nd
In the 2 paragraph, c), replace "3.5 of EN 292-2:1991/A1:1995" with "4.5 of EN ISO 12100-2:2003".
In the last paragraph, Verification, delete "For electrical components by requiring confirmation from the
manufacturer of any component which conforms to the relevant standards." and add the following NOTE:
"NOTE For electrical components characteristics the information from the electrical component supplier can be
useful.".
8 Modification to 5.1.3, Starting
In the first and second paragraphs replace "EN 60204-1:1992" twice with "EN 60204-1:2006".
9 Modification to 5.1.4.1, All machines
In the second paragraph, a) and b) replace "EN 60204-1:1992" twice with "EN 60204-1:2006".
10 Modification to 5.1.5, Emergency stop
In second and third paragraphs replace "EN 60204-1:1992" twice with "EN 60204-1:2006".
11 Modification to 5.1.8, Control duplication
In the first paragraph, replace "EN 292-2:1991/A1:1995" with "EN ISO 12100-2:2003".
12 Modification to 5.1.9, Failure of the power supply
In firs paragraph replace "EN 60204-1:1992" with "EN 60204-1:2006".
13 Modification to 5.2.1, Stability
Replace in second paragraph "Transportable machines" with "Displaceable machines".
9
---------------------- Page: 11 ----------------------
SIST EN 1807:2000/kprA1:2009
EN 1807:1999/prA1:2009 (E)
14 Modification to 5.2.2.1, Characteristics of guards
In the last paragraph, Verification, delete "and for the ultimate tensile strength a confirmation from the
manufacturer of the material", replace the last comma with an "and" and add the following NOTE:
"NOTE For the ultimate tensile strength a confirmation from the manufacturer of the material can be useful.".
15 Modification to 5
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.