EN ISO 15848-1:2015/A1:2017

Industrial valves - Measurement, test and qualification procedures for fugitive emissions - Part 1: Classification system and qualification procedures for type testing of valves - Amendment 1 (ISO 15848-1:2015/Amd 1:2017)

ISO 15848-1:2015 specifies testing procedures for evaluation of external leakage of valve stem seals (or shaft) and body joints of isolating valves and control valves intended for application in volatile air pollutants and hazardous fluids. End connection joints, vacuum application, effects of corrosion, and radiation are excluded from this part of ISO 15848.
ISO 15848-1:2015 concerns classification system and qualification procedures for type testing of valves.

Industriearmaturen - Mess-, Prüf- und Qualifikationsverfahren für flüchtige Emissionen - Teil 1: Klassifizierungssystem und Qualifikationsverfahren für die Bauartprüfung von Armaturen (ISO 15848-1:2015/Amd 1:2017)

Dieser Teil von ISO 15848 legt Prüfverfahren für die Bewertung der äußeren Undichtheit von Schaft- bzw. Wellenabdichtungen von Armaturen, Gehäuseverbindungen von Absperrventilen und Stellgeräten zur Ver¬wendung mit flüchtigen luftverunreinigenden Stoffen und gefährlichen Flüssigkeiten fest. Anschlussver¬bindungen, Anwendungen in der Vakuumtechnik, Auswirkungen von Korrosion und Bestrahlung fallen nicht in den Anwendungsbereich dieses Teils von ISO 15848.
Dieser Teil von ISO 15848 beinhaltet ein Klassifizierungssystem und Qualifikationsverfahren für die Durch¬führung von Bauartprüfungen an Armaturen.

Robinetterie industrielle - Mesurage, essais et modes opératoires de qualification pour émissions fugitives - Partie 1: Système de classification et modes opératoires de qualification pour les essais de type des appareils de robinetterie - Amendement 1 (ISO 15848-1:2015/Amd 1:2017)

ISO 158484-1:2015 spécifie des modes opératoires d'essai pour l'évaluation des fuites externes des dispositifs d'étanchéité de la tige (ou de l'arbre) de l'appareil de robinetterie, et des jonctions du corps des robinets de sectionnement et des robinets de régulation destinés à être utilisés au contact de polluants atmosphériques volatils et de fluides dangereux. Les jonctions des raccords d'extrémité, les applications sous vide, les effets de la corrosion et des rayonnements sont exclus de la présente partie de l'ISO 15848.
ISO 158484-1:2015 concerne le système de classification et les modes opératoires de qualification pour les essais de type des appareils de robinetterie.

Industrijski ventili - Meritve, preskusi in postopki kvalificiranja pobeglih emisij - 1. del: Klasifikacijski sistem in kvalifikacijski postopki za preskušanje tipa ventilov - Dopolnilo A1 (ISO 15848-1:2015/Amd 1:2017)

General Information

• Status: Published
• Publication Date: 21-Mar-2017
• Withdrawal Date: 29-Sep-2017
• ICS: 23.060.01 - Valves in general
• Technical Committee: CEN/TC 69 - Industrial valves
• Drafting Committee: CEN/TC 69/WG 1 - Basic standards
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 22-Mar-2017
• Completion Date: 22-Mar-2017
• Ref Project: SIST EN ISO 15848-1:2015/A1:2017 - Industrial valves - Measurement, test and qualification procedures for fugitive emissions - Part 1: Classification system and qualification procedures for type testing of valves - Amendment 1 (ISO 15848-1:2015/Amd 1:2017)

Relations

• Amends: EN ISO 15848-1:2015 - Industrial valves - Measurement, test and qualification procedures for fugitive emissions - Part 1: Classification system and qualification procedures for type testing of valves (ISO 15848-1:2015)
• Effective Date: 13-Apr-2016

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 15848-1:2015/oprA1:2016
01-julij-2016
Industrijski ventili - Meritve, preskusi in postopki kvalificiranja pobeglih emisij - 1.
del: Klasifikacijski sistem in kvalifikacijski postopki za preskušanje tipa ventilov -
Dopolnilo A1
Industrial valves - Measurement, test and qualification procedures for fugitive emissions -
Part 1: Classification system and qualification procedures for type testing of valves -
Amendment 1
Robinetterie industrielle - Mesurage, essais et modes opératoires de qualification pour
émissions fugitives - Partie 1: Système de classification et modes opératoires de
qualification pour les essais de type des appareils de robinetterie - Amendement 1
Ta slovenski standard je istoveten z: EN ISO 15848-1:2015/prA1
ICS:
23.060.01 Ventili na splošno Valves in general
SIST EN ISO 15848-1:2015/oprA1:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 15848-1:2015/oprA1:2016

---------------------- Page: 2 ----------------------

SIST EN ISO 15848-1:2015/oprA1:2016
DRAFT AMENDMENT
ISO 15848-1:2015/DAM 1
ISO/TC 153 Secretariat: AFNOR
Voting begins on: Voting terminates on:
2016-06-07 2016-08-29
Industrial valves — Measurement, test and qualification
procedures for fugitive emissions —
Part 1:
Classification system and qualification procedures for type
testing of valves
AMENDMENT 1
Robinetterie industrielle — Mesurage, essais et modes opératoires de qualification pour émissions
fugitives —
Partie 1: Système de classification et modes opératoires de qualification pour les essais de type des
appareils de robinetterie
AMENDEMENT 1
ICS: 23.060.01
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
To expedite distribution, this document is circulated as received from the
IN ADDITION TO THEIR EVALUATION AS
committee secretariat. ISO Central Secretariat work of editing and text
BEING ACCEPTABLE FOR INDUSTRIAL,
composition will be undertaken at publication stage.
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO 15848-1:2015/DAM 1:2016(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2016

---------------------- Page: 3 ----------------------

SIST EN ISO 15848-1:2015/oprA1:2016
ISO 15848-1:2015/DAM 1:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 4 ----------------------

SIST EN ISO 15848-1:2015/oprA1:2016
ISO 15848-1:2015/DAM 1:2016(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.
...

SLOVENSKI STANDARD
SIST EN ISO 15848-1:2015/A1:2017
01-junij-2017
Industrijski ventili - Meritve, preskusi in postopki kvalificiranja pobeglih emisij - 1.
del: Klasifikacijski sistem in kvalifikacijski postopki za preskušanje tipa ventilov -
Dopolnilo A1 (ISO 15848-1:2015/Amd 1:2017)
Industrial valves - Measurement, test and qualification procedures for fugitive emissions -
Part 1: Classification system and qualification procedures for type testing of valves -
Amendment 1 (ISO 15848-1:2015/Amd 1:2017)
Industriearmaturen - Mess-, Prüf- und Qualifikationsverfahren für flüchtige Emissionen -
Teil 1: Klassifizierungssystem und Qualifikationsverfahren für die Bauartprüfung von
Armaturen (ISO 15848-1:2015/Amd 1:2017)
Robinetterie industrielle - Mesurage, essais et modes opératoires de qualification pour
émissions fugitives - Partie 1: Système de classification et modes opératoires de
qualification pour les essais de type des appareils de robinetterie - Amendement 1 (ISO
15848-1:2015/Amd 1:2017)
Ta slovenski standard je istoveten z: EN ISO 15848-1:2015/A1:2017
ICS:
23.060.01 Ventili na splošno Valves in general
SIST EN ISO 15848-1:2015/A1:2017 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 15848-1:2015/A1:2017

---------------------- Page: 2 ----------------------

SIST EN ISO 15848-1:2015/A1:2017


EN ISO 15848-1:2015/A1
EUROPEAN STANDARD

NORME EUROPÉENNE

March 2017
EUROPÄISCHE NORM
ICS 23.060.01
English Version

Industrial valves - Measurement, test and qualification
procedures for fugitive emissions - Part 1: Classification
system and qualification procedures for type testing of
valves - Amendment 1 (ISO 15848-1:2015/Amd 1:2017)
Robinetterie industrielle - Mesurage, essais et modes Industriearmaturen - Mess-, Prüf- und
opératoires de qualification pour émissions fugitives - Qualifikationsverfahren für flüchtige Emissionen - Teil
Partie 1: Système de classification et modes 1: Klassifizierungssystem und Qualifikationsverfahren
opératoires de qualification pour les essais de type des für die Bauartprüfung von Armaturen (ISO 15848-
appareils de robinetterie - Amendement 1 (ISO 15848- 1:2015/Amd 1:2017)
1:2015/Amd 1:2017)
This amendment A1 modifies the European Standard EN ISO 15848-1:2015; it was approved by CEN on 15 March 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15848-1:2015/A1:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 15848-1:2015/A1:2017
EN ISO 15848-1:2015/A1:2017 (E)
Contents Page
European foreword . 3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 15848-1:2015/A1:2017
EN ISO 15848-1:2015/A1:2017 (E)
European foreword
This document (EN ISO 15848-1:2015/A1:2017) has been prepared by Technical Committee
ISO/TC 153 “Valves” in collaboration with Technical Committee CEN/TC 69 “Industrial valves” the
secretariat of which is held by AFNOR.
This Amendment to the European Standard EN ISO 15848-1:2015 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by September 2017,
and conflicting national standards shall be withdrawn at the latest by September 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held r
...