EN ISO 14253-3:2011
(Main)Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 3: Guidelines for achieving agreements on measurement uncertainty statements (ISO 14253-3:2011)
Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 3: Guidelines for achieving agreements on measurement uncertainty statements (ISO 14253-3:2011)
ISO 14253-3:2011 provides guidelines and defines procedures for assisting the customer and supplier to reach amicable agreements on disputed measurement uncertainty statements regulated in accordance with ISO 14253-1, and so avoid costly and time-consuming disputes.
Geometrische Produktspezifikation (GPS) - Prüfung von Werkstücken und Messgeräten durch Messen - Teil 3: Richtlinien für das Erzielen einer Einigung über Messunsicherheitsangaben (ISO 14253-3:2011)
Dieser Teil von ISO 14253 bietet Orientierungshilfen und legt Verfahren fest, die Kunden und Lieferanten
helfen, Einigung bei Auseinandersetzungen über Messunsicherheitsangaben nach ISO 14253-1 zu erzielen.
Dadurch werden kostenintensive und zeitraubende Auseinandersetzungen vermieden.
Spécification géométrique des produits (GPS) - Vérification par la mesure des pièces et des équipements de mesure - Partie 3: Lignes directrices pour l'obtention d'accords sur la déclaration des incertitudes de mesure (ISO 14253-3:2011)
L'ISO 14253-3:2011 fournit des lignes directrices et définit des procédures pour aider le client et le fournisseur à parvenir à un accord à l'amiable concernant des déclarations d'incertitude de mesure contestées, obtenues conformément aux règles décrites dans l'ISO 14253‑1, évitant ainsi des désagréments coûteux en temps et en argent.
Specifikacija geometrijskih veličin izdelka - Kontrola z merjenjem obdelovancev in merilna oprema - 3. del: Smernice za doseganje soglasja glede navedb o merilni negotovosti (ISO 14253-3:2011)
Ta del ISO 14253 podaja smernice in opredeljuje postopke za pomoč kupcu in dobavitelju pri sklepanju prijateljskih dogovorov o spornih izjavah o negotovosti meritve, ki se urejajo v skladu z ISO 14253-1, da ne bi prihajalo do dragih in dolgotrajnih nesporazumov.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2011
1DGRPHãþD
SIST ISO/TS 14253-3:2003
SIST-TS CEN ISO/TS 14253-3:2008
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND.RQWUROD]PHUMHQMHPREGHORYDQFHYLQ
PHULOQDRSUHPDGHO 6PHUQLFH]DGRVHJDQMHVRJODVMDJOHGHQDYHGERPHULOQL
QHJRWRYRVWL ,62
Geometrical product specifications (GPS) - Inspection by measurement of workpieces
and measuring equipment - Part 3: Guidelines for achieving agreements on
measurement uncertainty statements (ISO 14253-3:2011)
Geometrische Produktspezifikation (GPS) - Prüfung von Werkstücken und Messgeräten
durch Messen - Teil 3: Richtlinien für das Erzielen einer Einigung über
Messunsicherheitsangaben (ISO 14253-3:2011)
Spécification géométrique des produits (GPS) - Vérification par la mesure des pièces et
des équipements de mesure - Partie 3: Lignes directrices pour l'obtention d'accords sur
la déclaration des incertitudes de mesure (ISO 14253-3:2011)
Ta slovenski standard je istoveten z: EN ISO 14253-3:2011
ICS:
17.040.30 Merila Measuring instruments
17.040.40 6SHFLILNDFLMDJHRPHWULMVNLK Geometrical Product
YHOLþLQL]GHOND *36 Specification (GPS)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 14253-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2011
ICS 17.040.01 Supersedes CEN ISO/TS 14253-3:2007
English Version
Geometrical product specifications (GPS) - Inspection by
measurement of workpieces and measuring equipment - Part 3:
Guidelines for achieving agreements on measurement
uncertainty statements (ISO 14253-3:2011)
Spécification géométrique des produits (GPS) - Vérification Geometrische Produktspezifikation (GPS) - Prüfung von
par la mesure des pièces et des équipements de mesure - Werkstücken und Messgeräten durch Messen - Teil 3:
Partie 3: Lignes directrices pour l'obtention d'accords sur la Richtlinien für das Erzielen einer Einigung über
déclaration des incertitudes de mesure (ISO 14253-3:2011) Messunsicherheitsangaben (ISO 14253-3:2011)
This European Standard was approved by CEN on 14 April 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14253-3:2011: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 14253-3:2011) has been prepared by Technical Committee ISO/TC 213 "Dimensional
and geometrical product specifications and verification" in collaboration with Technical Committee
CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is
held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at
the latest by October 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN ISO/TS 14253-3:2007.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 14253-3:2011 has been approved by CEN as a EN ISO 14253-3:2011 without any
modification.
INTERNATIONAL ISO
STANDARD 14253-3
First edition
2011-04-15
Geometrical product specifications
(GPS) — Inspection by measurement of
workpieces and measuring equipment —
Part 3:
Guidelines for achieving agreements
on measurement uncertainty statements
Spécification géométrique des produits (GPS) — Vérification par la
mesure des pièces et des équipements de mesure —
Partie 3: Lignes directrices pour l'obtention d'accords sur la déclaration
des incertitudes de mesure
Reference number
ISO 14253-3:2011(E)
©
ISO 2011
ISO 14253-3:2011(E)
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
ISO 14253-3:2011(E)
Contents Page
Foreword . iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Reaching an agreement on a stated expanded uncertainty . 2
5 Sequential procedure for evaluating and reaching agreement on an uncertainty statement . 5
Annex A (informative) Relation to the GPS matrix model . 10
Bibliography . 12
ISO 14253-3:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 14253-3 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product
specifications and verification.
This first edition of ISO 14253-3 cancels and replaces ISO/TS 14253-3:2002, which has been technically
revised.
ISO 14253 consists of the following parts, under the general title Geometrical product specifications (GPS) —
Inspection by measurement of workpieces and measuring equipment:
Part 1: Decision rules for proving conformance or non-conformance with specifications
Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring
equipment and in product verification
Part 3: Guidelines for achieving agreements on measurement uncertainty statements
Part 4: Background on functional limits and specification limits in decision rules [Technical Specification]
iv © ISO 2011 – All rights reserved
ISO 14253-3:2011(E)
Introduction
This part of ISO 14253 is a geometrical product specification (GPS) International Standard and is to be
regarded as a global GPS Standard (see ISO/TR 14638). It influences links 4, 5 and 6 of all chains of
standards in the general GPS matrix.
The ISO/GPS Masterplan given in ISO/TR 14638 gives an overview of the ISO/GPS system of which this part
of ISO 14253 is a part. The fundamental rules of ISO/GPS given in ISO 8015 apply to this part of ISO 14253
and the default decision rules given in ISO 14253-1 apply to specifications made in accordance with this part
of ISO 14253, unless otherwise indicated.
For more detailed information on the relation of this International Standard to other standards and the GPS
matrix model, see Annex A.
ISO 14253-1 provides decision rules for proving conformance or non-conformance with specifications of
workpieces and measuring equipment when taking into account the uncertainty of measurement. ISO 14253-2
provides instructions for preparing uncertainty budgets for determining measurement uncertainty as defined in
the Guide to the Expression of Uncertainty in Measurement (GUM). However, the possibility still exists that
disagreement between customer and supplier can occur on the estimated measurement uncertainty.
It is becoming increasingly common for suppliers to have in place a quality system providing satisfactory
assurance to the customer that the latter is receiving a product which conforms to specifications. This avoids
the need for costly duplicate inspections.
For this reason, the most common case of disagreement over a measurement uncertainty statement or an
uncertainty budget involves the customer questioning the supplier's uncertainty budget. The customer may
also question the measured value of a characteristic of a workpiece or of measuring equipment, thus indirectly
questioning the total uncertainty budget (see ISO 14253-1).
In a rarer case of disagreement, the supplier may question the customer's uncertainty budget when the
customer rejects a workpiece or measuring equipment (see ISO 14253-1:1998, 6.2).
In addition to those mentioned, there are other cases of disagreement, as well as other motivations that may
lead to discussion of stated uncertainties.
INTERNATIONAL STANDARD ISO 14253-3:2011(E)
Geometrical product specifications (GPS) — Inspection
by measurement of workpieces and measuring equipment —
Part 3:
Guidelines for achieving agreements on measurement
uncertainty statements
1 Scope
This part of ISO 14253 provides guidelines and defines procedures for assisting the customer and supplier to
reach amicable agreements on disputed measurement uncertainty statements regulated in accordance with
ISO 14253-1, and so avoid costly and time-consuming disputes.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 14253-1:1998, Geometrical Product Specifications (GPS) — Inspection by measurement of workpieces
and measuring equipment — Part 1: Decision rules for proving conformance or non-conformance with
specifications
ISO 14253-2:2011, Geometrical product specifications (GPS) — Inspection by measurement of workpieces
and measuring equipment — Part 2: Guidance for the estimation of uncertainty in GPS measurement, in
calibration of measuring equipment and in product verification
ISO 14978:2006, Geometrical product specifications (GPS) — General concepts and requirements for GPS
measuring equipment
1)
ISO 17450-1:— , Geometrical product specifications (GPS) — General concepts — Part 1: Model for
geometrical specification and verification
2)
ISO 17450-2:— , Geometrical product specifications (GPS) — General concepts — Part 2: Basic tenets,
s
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.