CEN ISO/TS 14253-3:2007
(Main)Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 3: Guidelines for achieving agreements on measurement uncertainty statements (ISO/TS 14253-3:2002)
Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 3: Guidelines for achieving agreements on measurement uncertainty statements (ISO/TS 14253-3:2002)
ISO/TS 14253 provides guidelines and defines procedures for assisting the customer and supplier to reach amicable agreements on disputed measurement uncertainty statements regulated in accordance with ISO 14253-1, and so avoid costly and time-consuming disputes.
Geometrische Produktspezifikation (GPS) - Prüfung von Werkstücken und Messgeräten durch Messen - Teil 3: Richtlinien für das Erzielen einer Einigung über Messunsicherheitsangaben (ISO/TS 14253-3:2002)
Dieser Teil von ISO 14253 legt Regeln und Verfahren fest, die Kunden und Lieferanten helfen, Einigung bei Auseinandersetzungen über Messunsicherheitsangaben nach ISO 14253 1 zu erzielen. Dadurch werden kostenintensive und zeitraubende Auseinandersetzungen vermieden.
Spécification géométrique des produits (GPS) - Vérification par la mesure des pièces et des équipements de mesure - Partie 3: Lignes directrices pour l'obtention d'accords sur la déclaration des incertitudes de mesure (ISO/TS 14253-3:2002)
L'ISO/TS 14253-3 fournit des lignes directrices et définit des procédures dans le but d'aider le client et le fournisseur à parvenir à un accord à l'amiable concernant des déclarations d'incertitude de mesure contestées, comme il est décrit dans l'ISO 14253-1, évitant ainsi des désagréments coûteux en temps et en argent.
Specifikacija geometrijskih veličin izdelka - Kontrola z merjenjem obdelovancev in merilna oprema - 3. del: Navodila za doseganje soglasja glede navedb o merilni negotovosti (ISO/TS 14253-3:2002)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2008
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND.RQWUROD]PHUMHQMHPREGHORYDQFHYLQ
PHULOQDRSUHPDGHO 1DYRGLOD]DGRVHJDQMHVRJODVMDJOHGHQDYHGERPHULOQL
QHJRWRYRVWL ,6276
Geometrical product specifications (GPS) - Inspection by measurement of workpieces
and measuring equipment - Part 3: Guidelines for achieving agreements on
measurement uncertainty statements (ISO/TS 14253-3:2002)
Geometrische Produktspezifikation (GPS) - Prüfung von Werkstücken und Messgeräten
durch Messen - Teil 3: Richtlinien für das Erzielen einer Einigung über
Messunsicherheitsangaben (ISO/TS 14253-3:2002)
Spécification géométrique des produits (GPS) - Vérification par la mesure des pieces et
des équipements de mesure - Partie 3: Lignes directrices pour l'obtention d'accords sur
la déclaration des incertitudes de mesure (ISO/TS 14253-3:2002)
Ta slovenski standard je istoveten z: CEN ISO/TS 14253-3:2007
ICS:
17.040.01
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
TECHNICAL SPECIFICATION
CEN ISO/TS 14253-3
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
December 2007
ICS 17.040.01
English Version
Geometrical product specifications (GPS) - Inspection by
measurement of workpieces and measuring equipment - Part 3:
Guidelines for achieving agreements on measurement
uncertainty statements (ISO/TS 14253-3:2002)
Spécification géométrique des produits (GPS) - Vérification Geometrische Produktspezifikation (GPS) - Prüfung von
par la mesure des pièces et des équipements de mesure - Werkstücken und Messgeräten durch Messen - Teil 3:
Partie 3: Lignes directrices pour l'obtention d'accords sur la Richtlinien für das Erzielen einer Einigung über
déclaration des incertitudes de mesure (ISO/TS 14253- Messunsicherheitsangaben (ISO/TS 14253-3:2002)
3:2002)
This Technical Specification (CEN/TS) was approved by CEN on 8 October 2007 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TS 14253-3:2007: E
worldwide for CEN national Members.
Contents Page
Foreword.3
Foreword
The text of ISO/TS 14253-3:2002 has been prepared by Technical Committee ISO/TC 213 “Dimensional and
geometrical product specifications and verification” of the International Organization for Standardization (ISO)
and has been taken over as CEN ISO/TS 14253-3:2007 by Technical Committee CEN/TC 290 “Dimensional
and geometrical product specification and verification” the secretariat of which is held by AFNOR.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO/TS 14253-3:2002 has been approved by CEN as a CEN ISO/TS 14253-3:2007 without any
modification.
TECHNICAL ISO/TS
SPECIFICATION 14253-3
First edition
2002-10-15
Geometrical Product Specifications
(GPS) — Inspection by measurement of
workpieces and measuring equipment —
Part 3:
Guidelines for achieving agreements on
measurement uncertainty statements
Spécification géométrique des produits (GPS) — Vérification par la mesure
des pièces et des équipements de mesure —
Partie 3: Lignes directrices pour l'obtention d'accords sur la déclaration des
incertitudes de mesure
Reference number
ISO/TS 14253-3:2002(E)
©
ISO 2002
ISO/TS 14253-3:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2002 – All rights reserved
ISO/TS 14253-3:2002(E)
Contents Page
Foreword . iv
Introduction. v
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 2
4 Reaching an agreement on a stated expanded uncertainty . 4
5 Sequential procedure for evaluating and reaching agreement on an uncertainty statement. 7
Annex A (informative) Relation to the GPS matrix model . 12
Bibliography. 13
ISO/TS 14253-3:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
In other circumstances, particularly when there is an urgent market requirement for such documents, a technical
committee may decide to publish other types of normative document:
an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical experts in an
ISO working group and is accepted for publication if it is approved by more than 50 % of the members of the
parent committee casting a vote;
an ISO Technical Specification (ISO/TS) represents an agreement between the members of a technical
committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting a
vote.
An ISO/PAS or ISO/TS is reviewed after three years with a view to deciding whether it should be confirmed for a
further three years, revised to become an International Standard, or withdrawn. In the case of a confirmed ISO/PAS
or ISO/TS, it is reviewed again after six years at which time it has to be either transposed into an International
Standard or withdrawn.
Attention is drawn to the possibility that some of the elements of this part of ISO/TS 14253 may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/TS 14253-3 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product
specifications and verification.
ISO 14253 consists of the following parts, under the general title Geometrical Product Specifications (GPS) —
Inspection by measurement of workpieces and measuring equipment:
Part 1: Decision rules for proving conformance or non-conformance with specifications
Part 2: Guide to the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and
in product verification
Part 3: Guidelines for achieving agreements on measurement uncertainty statements
Annex A of this part of ISO 14253 is for information only.
iv © ISO 2002 – All rights reserved
ISO/TS 14253-3:2002(E)
Introduction
This part of ISO 14253 is a geometrical product specification (GPS) Technical Specification and is to be regarded
as a global GPS Technical Specification (see ISO/TR 14638). It influences links 4, 5 and 6 of all chains of
standards in the general GPS matrix.
For more detailed information of the relation of this Technical Specification to other standards and the GPS matrix
model, see annex A.
ISO 14253-1 provides decision rules for proving conformance or non-conformance with specifications of
workpieces and measuring equipment when taking into account the uncertainty of measurement. ISO/TS 14253-2
provides instructions for preparing uncertainty budgets for determining measurement uncertainty as defined in the
Guide to the Expression of Uncertainty in Measurement (GUM). However, the possibility still exists that
disagreement between customer and supplier can occur on the estimated measurement uncertainty.
It is becoming increasingly common for suppliers to have in place a quality system providing satisfactory assurance
to the customer that the latter is receiving a product which conforms to specifications. This avoids the need for
costly duplicate inspections.
For this reason, the most common case of disagreement over a measurement uncertainty statement or an
uncertainty budget involves the customer questioning the supplier's uncertainty budget. The customer also may
question the measured value of a characteristic of a workpiece or of measuring equipment, thus indirectly
questioning the total uncertainty budget (see ISO 14253-1).
In a rarer case of disagreement, the supplier may question the customer’s uncertainty budget when the customer
rejects a workpiece or measuring equipment (see 6.2 of ISO 14253-1:1998).
In addition to those mentioned, there are other cases of disagreement, as well as other motivations that may lead
to discussion of stated uncertainties.
TECHNICAL SPECIFICATION ISO/TS 14253-3:2002(E)
Geometrical Product Specifications (GPS) — Inspection by
measurement of workpieces and measuring equipment —
Part 3:
Guidelines for achieving agreements on measurement uncertainty
statements
1 Scope
This part of ISO 14253 provides guidelines and defines procedures for assisting the customer and supplier to reach
amicable agreements on disputed measurement uncertainty statements regulated in accordance with ISO 14253-1,
and so avoid costly and time-consuming disputes.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this part of ISO 14253. For dated references, subsequent amendments to, or revisions of, any of these publications
do not apply. However, parties to agreements based on this part of ISO 14253 are encouraged to investigate the
possibility of applying the most recent editions of the normative documents indicated below. For undated
references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain
registers of c
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.