EN 12629-1:2000/FprA1

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 1: Common requirements

Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 1: Gemeinsame Anforderungen

Machines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 1: Exigences communes

Stroji za izdelavo gradbenih proizvodov iz betona in apnenega peščenca - Varnost - 1. del: Splošne zahteve

General Information

• Status: Not Published
• ICS: 91.220 - Construction equipment
• Technical Committee: CEN/TC 151 - Construction equipment and building material machines - Safety
• Drafting Committee: CEN/TC 151/WG 10 - Machines and plant for the production of stones, slabs, pipes, prefabricated elements of concrete and calcium-silicate - Safety
• Current Stage: 5060 - Closure of Vote - Formal Approval
• Start Date: 04-Jul-2010
• Due Date: 12-May-2009
• Completion Date: 04-Jul-2010
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Directive: 98/37/EC - Machinery
• Mandate: M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: SIST EN 12629-1:2000/kFprA1:2010 - Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 1: Common requirements

Relations

• Merged Into: EN 12629-1:2000+A1:2010 - Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 1: Common requirements
• Effective Date: 10-Jul-2010
• Amends: EN 12629-1:2000 - Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 1: Common requirements
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
01-april-2010
6WURML]DL]GHODYRJUDGEHQLKSURL]YRGRYL]EHWRQDLQDSQHQHJDSHãþHQFD9DUQRVW
GHO6SORãQH]DKWHYH
Machines for the manufacture of constructional products from concrete and calcium-
silicate - Safety - Part 1: Common requirements
Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen -
Sicherheit - Teil 1: Gemeinsame Anforderungen
Machines pour la fabrication de produits de construction en béton et silico-calcaire -
Sécurité - Partie 1: Exigences communes
Ta slovenski standard je istoveten z: EN 12629-1:2000/FprA1
ICS:
91.220 Gradbena oprema Construction equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
FINAL DRAFT
EN 12629-1:2000
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
February 2010
ICS 91.220
English Version
Machines for the manufacture of constructional products from
concrete and calcium-silicate - Safety - Part 1: Common
requirements
Machines pour la fabrication de produits de construction en Maschinen für die Herstellung von Bauprodukten aus Beton
béton et silico-calcaire - Sécurité - Partie 1: Exigences und Kalksandsteinmassen - Sicherheit - Teil 1:
communes Gemeinsame Anforderungen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 151.
This draft amendment A1, if approved, will modify the European Standard EN 12629-1:2000. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12629-1:2000/FprA1:2010: E
worldwide for CEN national Members.

Contents Page
Foreword .3
1 Modifications to the Foreword .4
2 Modifications to the Introduction .5
3 Modifications to Clause 1 (Scope) .5
4 Modifications to Clause 2 (Normative references) .5
5 Modifications to Clause 3 (Definitions) .7
6 Modifications to Clause 5 (Safety requirements and/or measures) .7
7 Modifications to Clause 6 (Verification of safety measures and/or provisions) . 11
8 Modifications to Clause 7 (Information for use) . 11
9 Modifications to Clause 8 (Marking) . 12
10 Modifications to Annex B . 12
11 Modification to Annex ZA, Relationship between this European Standard and the
Essential Requirements of EU Directive 98/37/EC . 13
12 Addition of a new Annex ZB, Relationship between this European Standard and the
Essential Requirements of EU Directive 2006/42/EC . 14
13 Modification to the Bibliography . 14
Bibliography . 14

Foreword
This document (EN 12629-1:2000/FprA1:2010) has been prepared by Technical Committee CEN/TC 151
“Construction equipment and building material machines - Safety”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annexes ZA and B, which are integral parts of this
document.
1 Modifications to the Foreword
th
Replace the 4 paragraph with the following:
"For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document."
th
Replace the 6 paragraph with the following:
"The series "Machines for the manufacture of constructional products from concrete and calcium – silicate –
Safety" consists of the following parts:
Part 1: Common requirements
Part 2: Block making machines
Part 3: Slide and turntable machines
Part 4: Concrete roof tile making machines
Part 5.1: Pipe making machines manufacturing in the vertical axis
Part 5.2: Pipe making machines manufacturing in the horizontal axis
Part 5.3: Pipe prestressing machines
Part 5.4: Concrete pipe coating machines
Part 6: Stationary and mobile equipment for the manufacture of precast reinforced products
Part 7: Stationary and mobile equipment for long line manufacture of prestressed products
Part 8: Machines and equipment for the manufacture of constructional products from calcium silicate (and
concrete)."
Delete the last paragraph.
2 Modifications to the Introduction
First paragraph, change the reference as follows:
Replace "EN 1070:1998” with "EN ISO 12100”.

3 Modifications to Clause 1 (Scope)
Sub-clause 1.2, replace the existing text with the following:
"This European Standard deals with hazards listed in Clause 4 which can arise during the operation and
maintenance, including the interfaces, of the machines for the manufacture of constructional products
from concrete and calcium silicate, when carried out as intended and under conditions of misuse which
are reasonably foreseeable by the manufacturer.
Part 2 to 8 of this standard give additional specific requirements and therefore have to be applied together
with this part."
Sub-clause 1.3, up-date the references as follows:
Replace "prEN 12151:1995" with "EN 12151:2007".
Delete sub-clause 1.4.
Sub-clause 1.5, up-date the references as follows:
Renumber “1.5” into “1.4”.
Replace "prEN 12629-2 to -8" with "EN 12629-2 to -8".
Add the following new sub-clause 1.5:
"1.5 This document is not applicable to machines for the manufacture of constructional products from
concrete and/or calcium silicate, which are manufactured before the date of publication of this document
by CEN."
4 Modifications to Clause 2 (Normative references)
Replace with the following text:
"The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 349:1993, Safety of machinery — Minimum gaps to avoid crushing of parts of the human body
EN 457:1992, Safety of machinery — Auditory danger signals — General requirements, design and
testing
EN 547-1:1996, Safety of machinery — Human body measurements — Part 1: Principles for determining
the dimensions required for openings for whole body access into machinery
EN 547-2:1996, Safety of machinery — Human body measurements — Part 2: Principles for determining
the dimensions required for access openings
EN 547-3:1996, Safety of machinery — Human body measurements – Part 3: Anthropometric data
EN 574, Safety of machinery — Two hand control devices – Functional aspects — Principles for design
EN 614-1:2006, Safety of machinery — Ergonomic design principles — Part 1: Terminology and general
principles
EN 626-1:1994, Safety of machinery — Reduction of risks to health from hazardous substances emitted
by machinery — Part 1: Principles and specifications for machinery manufacturers
EN 894-1:1997, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators – Part 1: General principles for human interactions with displays and control actuators
EN 894-2:1997, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators – Part 2: Displays
EN 894-3:2000, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators – Part 3: Control actuators
EN 953:1997, Safety of machinery — Guards — General requirements for the design and construction of
fixed and movable guards
EN 954-1:1996, Safety of machinery — Safety-related parts of control systems — Part 1: General
principles for design
EN 982:1996, Safety of machinery — Safety requirements for fluid power systems and their components
— Hydraulics
EN 983:1996, Safety of machinery — Safety requirements for fluid power systems and their components
– Pneumatics
EN 999, Safety of machinery — The positioning of protective equipment in respect of approach speeds of
parts of the human body
EN 1037:1995, Safety of machinery — Prevention of unexpected start-up
EN 1088, Safety of machinery — Interlocking devices associated with guards — Principles for design and
selection
EN ISO 3746:2009, Acoustics — Determination of sound power levels of noise sources using sound
pressure — Survey method using an enveloping measurement surface over a reflecting plane (ISO
3746:1995, including Cor 1:1995)
EN ISO 11204:2009, Acoustics — Noise emitted by machinery and equipment — Measurement of
emission sound pressure levels at a work station and at other specified positions — Method requiring
environmental corrections (ISO 11204:1995, including Cor 1:1997)
EN ISO 11688-1:1998, Acoustics — Recommended practice for the design of low-noise machinery and
equipment — Part 1: Planning (ISO /TR 11688-1:1995)
EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1:
Basic terminology, methodology (ISO 12100-1:2003)
EN ISO 12100-2:2003, Safety of machinery — Basic concepts, general principles for design — Part 2:
Technical principles (ISO 12100-2:2003)
EN ISO 13850:2008, Safety of machinery — Emergency stop — Principles for design (ISO 13850:2006)
EN ISO 13857:2008, Safety of machinery — Safety distances to prevent hazard zones being reached by
upper and lower limbs (ISO 13857:2008)
EN ISO 14122-1:2001, Safety of machinery — Permanent means of access to machinery — Part 1:
Choice of fixed means of access between two levels (ISO 14122-1:2001)
EN ISO 14122-2:2001, Safety of machinery — Permanent means of access to machinery — Part 2:
Working platforms and walkways (ISO 14122-2:2001)
EN ISO 14122-3:2001, Safety of machinery — Permanent means of access to machinery — Part 3:
Stairs, stepladders and guard-rails (ISO 14122-3:2001)
EN ISO 14122-4:2004, Safety of machinery — Permanent means of access to machinery — Part 4: Fixed
ladders (ISO 14122-4:2004)
EN 60204-1:2006, Safety of machinery — Electrical equipment of machines — Part 1: General
requirements (IEC 60204-1:2005, modified)
EN 61310-1:2008, Safety of machinery — Indication, marking and actuation — Part 1: Requirements for
visual, acoustic and tactile signals (IEC 61310-1:2007)
EN 61496-1:2004, Safety of machinery — Electro-sensitive protective equipment — Part 1: General
requirements and tests (IEC 61496-1:2004, modified)"

5 Modifications to Clause 3 (Definitions)
Replace the title with the following
"3 Terms and definitions"
Replace the first paragraph with the following:
"For the purposes of this document, the terms and definitions given in EN ISO 12100-1:2003 apply.
Additional definitions specifically needed for EN 12629 series are given below:"
Sub-clauses 3.1.2 and 3.1.3, up-date the reference as follows:
Replace "(See prEN 1340:1993)" with "(See EN 1340:2003)".

6 Modifications to Clause 5 (Safety requirements and/or measures)
Headline, modify as follows:
Replace “Safety requirements and/or measures” with “Safety requirements and/or protective measures”.
First paragraph, replace with the following text:
"Machinery shall comply with the safety requirements and/or protective measures of this clause. In
addition, the machine shall be designed according to the principles of EN ISO 12100 for relevant but no
...