EN ISO 5821:2009
(Main)Resistance welding - Spot welding electrode caps (ISO 5821:2009)
Resistance welding - Spot welding electrode caps (ISO 5821:2009)
ISO 5821:2009 specifies the dimensions and tolerances of resistance spot welding electrode caps, where a female taper is used to fix the cap to an electrode adaptor.
ISO 5821:2009 applies only to electrode caps for which the electrode force given for diameters 13 mm, 16mm and 20 mm (taper 1:10) and for diameters 12,7 mm, 15,8 mm and 19,1 mm (taper 1:9,6) is not exceeded.
Widerstandsschweißen - Punktschweiß-Elektrodenkappen (ISO 5821:2009)
Diese Internationale Norm legt Maße und Grenzabweichungen für Punktschweiß-Elektrodenkappen fest, bei denen ein Innenkegel (siehe ISO 1089) verwendet wird, um die Elektrodenkappen auf dem Elektrodenschaft (siehe ISO 5183-1 und ISO 5183-2) zu befestigen.
Sie gilt nur für Elektrodenkappen, für welche die Elektrodenkraft FE, die für den Durchmesser d1 in Tabelle 2 und Tabelle A.2 angegeben ist, nicht überschritten wird.
Soudage par résistance - Embouts amovibles de pointes d'électrodes pour soudage par points (ISO 5821:2009)
L'ISO 5821:2009 spécifie les dimensions et les tolérances des embouts amovibles de pointes d'électrodes pour le soudage par résistance par points, lorsqu'un cône femelle est utilisé pour fixer la pointe d'électrode à un embout amovible.
L'ISO 5821:2009 ne s'applique qu'aux embouts de pointes d'électrodes pour lesquels la force d'électrode donnée pour les diamètres 13 mm, 16 mm et 20 mm (cône 1:10) ainsi que pour les diamètres 12,7 mm, 15,8 mm et 19,1 mm (cône 1:9,6) n'excède pas les valeurs consignées.
Uporovno varjenje - Kape elektrod za točkovno varjenje (ISO 5821:2009)
Ta mednarodni standard določa dimenzije in dovoljena odstopanja kap elektrod za uporovno točkovno varjenje, pri katerih se za pritrjevanje kape na adapter elektrode (glej ISO 5183-1 in ISO 5183-2) uporablja ženska konica (glej ISO 1089). Velja le za kape elektrode, pri katerih ni presežen pritisk elektrode, FE, podan za premer d1 v preglednici 2 in preglednici A.2.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Widerstandsschweißen - Punktschweiß- Elektrodenkappen (ISO 5821:2009)Soudage par résistance - Embouts amovibles de pointes d'électrodes pour soudage par points (ISO 5821:2009)Resistance welding - Spot welding electrode caps (ISO 5821:2009)25.160.30Varilna opremaWelding equipmentICS:Ta slovenski standard je istoveten z:EN ISO 5821:2009SIST EN ISO 5821:2010en,fr01-april-2010SIST EN ISO 5821:2010SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 5821
November 2009 ICS 25.160.30 English Version
Resistance welding - Spot welding electrode caps (ISO 5821:2009)
Soudage par résistance - Embouts amovibles de pointes d'électrodes pour soudage par points (ISO 5821:2009)
Widerstandsschweißen - Punktschweiß-Elektrodenkappen (ISO 5821:2009) This European Standard was approved by CEN on 8 November 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 5821:2009: ESIST EN ISO 5821:2010
Reference numberISO 5821:2009(E)© ISO 2009
INTERNATIONAL STANDARD ISO5821Second edition2009-02-01Resistance welding — Spot welding electrode caps Soudage par résistance — Embouts amovibles de pointes d'électrodes pour soudage par points
ISO 5821:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2009 – All rights reserved
ISO 5821:2009(E) © ISO 2009 – All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 5821 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 6, Resistance welding and allied mechanical joining. This second edition cancels and replaces the first edition (ISO 5821:1979) which has been technically revised. Requests for official interpretations of any aspect of this International Standard should be directed to the Secretariat of ISO/TC 44/SC 6 via your national standards body, a complete listing of which can be found at www.iso.org.
INTERNATIONAL STANDARD ISO 5821:2009(E) © ISO 2009 – All rights reserved 1Resistance welding — Spot welding electrode caps 1 Scope This International Standard specifies the dimensions and tolerances of resistance spot welding electrode caps, where a female taper (see ISO 1089) is used to fix the cap to an electrode adaptor (see ISO 5183-1 and ISO 5183-2). It applies only to electrode caps for which the electrode force, FE, given for diameter d1 in Table 2 and Table A.2 is not exceeded. 2 Normative references The following referenced documents are indispensable for the application of th
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.