EN ISO 7759:2010
(Main)Anodizing of aluminium and its alloys - Measurement of reflectance characteristics of aluminium surfaces using a goniophotometer or an abridged goniophotometer (ISO/FDIS 7759:2010)
Anodizing of aluminium and its alloys - Measurement of reflectance characteristics of aluminium surfaces using a goniophotometer or an abridged goniophotometer (ISO/FDIS 7759:2010)
ISO 7759:2010 specifies a method for the measurement of the reflectance characteristics of high-gloss anodized aluminium surfaces.
The method described is also suitable for the measurement of the reflectance characteristics of other high-gloss metal surfaces.
The method is not suitable for diffuse-finish metal surfaces and does not measure colour.
Anodisieren von Aluminium und Aluminiumlegierungen - Messung der Reflexionseigenschaften von Aluminiumoberflächen mit einem Goniophotometer oder mit einem vereinfachten Goniophotometer (ISO/FDIS 7759:2010)
Diese Internationale Norm legt ein Verfahren zur Messung der Reflexionseigenschaften von hochglänzenden
anodisierten Aluminiumoberflächen fest.
Das beschriebene Verfahren ist ebenfalls zur Messung der Reflexionseigenschaften von anderen hochglänzenden
Metalloberflächen geeignet.
Das Verfahren ist weder für Oberflächen mit diffuser Reflexion noch zur Farbmessung geeignet.
Anodisation de l'aluminium et de ses alliages - Mesurage des caractéristiques de réflectivité des surfaces d'aluminium à l'aide d'un goniophotomètre normal ou simplifié (ISO/FDIS 7759:2010)
L'ISO 7759:2010 spécifie une méthode de mesurage des caractéristiques de réflectivité des surfaces en aluminium anodisé à haute brillance.
La méthode décrite est également applicable au mesurage des caractéristiques de la réflectivité d'autres surfaces métalliques à haute brillance.
La méthode n'est pas applicable aux surfaces métalliques à finition diffuse et ne mesure pas la couleur.
Anodizacija aluminija in aluminijevih zlitin - Merjenje značilnic odbojnosti aluminijevih površin z goniofotometrom ali poenostavljenim goniofotometrom (ISO 7759:2010)
Ta mednarodni standard določa metodo za merjenje značilnic odbojnosti visokosijajnih anodiziranih aluminijevih površin. Opisana metoda je primerna tudi za merjenje značilnic odbojnosti drugih visokosijajnih kovinskih površin. Metoda ni primerna za kovinske površine z difuzno apreturo in ne meri barve.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2012
1DGRPHãþD
SIST EN 12373-13:2002
$QRGL]DFLMDDOXPLQLMDLQDOXPLQLMHYLK]OLWLQ0HUMHQMH]QDþLOQLFRGERMQRVWL
DOXPLQLMHYLKSRYUãLQ]JRQLRIRWRPHWURPDOLSRHQRVWDYOMHQLPJRQLRIRWRPHWURP
,62
Anodizing of aluminium and its alloys - Measurement of reflectance characteristics of
aluminium surfaces using a goniophotometer or an abridged goniophotometer (ISO
7759:2010)
Anodisieren von Aluminium und Aluminiumlegierungen - Messung der
Reflexionseigenschaften von Aluminiumoberflächen mit vereinfachtem oder Präzisions-
Goniophotometer (ISO 7759:2010)
Anodisation de l'aluminium et de ses alliages - Mesurage des caractéristiques de
réflectivité des surfaces d'aluminium à l'aide d'un goniophotomètre normal ou simplifié
(ISO 7759:2010)
Ta slovenski standard je istoveten z: EN ISO 7759:2010
ICS:
25.220.20 Površinska obdelava Surface treatment
77.120.10 Aluminij in aluminijeve zlitine Aluminium and aluminium
alloys
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 7759
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2010
ICS 25.220.20 Supersedes EN 12373-13:2000
English Version
Anodizing of aluminium and its alloys - Measurement of
reflectance characteristics of aluminium surfaces using a
goniophotometer or an abridged goniophotometer (ISO
7759:2010)
Anodisation de l'aluminium et de ses alliages - Mesurage Anodisieren von Aluminium und Aluminiumlegierungen -
des caractéristiques de réflectivité des surfaces Messung der Reflexionseigenschaften von
d'aluminium à l'aide d'un goniophotomètre normal ou Aluminiumoberflächen mit einem Goniophotometer oder
simplifié (ISO 7759:2010) mit einem vereinfachten Goniophotometer (ISO 7759:2010)
This European Standard was approved by CEN on 31 August 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 7759:2010: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
The text of ISO 7759:2010 has been prepared by Technical Committee ISO/TC 79 "Light metals and their
alloys" of the International Organization for Standardization (ISO) and has been taken over as
which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2011, and conflicting national standards shall be withdrawn at
the latest by March 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12373-13:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 7759:2010 has been approved by CEN as a EN ISO 7759:2010 without any modification.
INTERNATIONAL ISO
STANDARD 7759
Second edition
2010-09-01
Anodizing of aluminium and its alloys —
Measurement of reflectance
characteristics of aluminium surfaces
using a goniophotometer or an abridged
goniophotometer
Anodisation de l'aluminium et de ses alliages — Mesurage des
caractéristiques de réflectivité des surfaces d'aluminium à l'aide d'un
goniophotomètre normal ou simplifié
Reference number
ISO 7759:2010(E)
©
ISO 2010
ISO 7759:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
ISO 7759:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Principle.1
5 Apparatus.2
6 Preparation and calibration of apparatus .5
6.1 General conditions .5
6.2 Geometric conditions.5
6.3 Spectral conditions .6
6.4 Calibration.6
7 Procedure.6
8 Expression of results.6
8.1 General.6
8.2 Specular reflectance R .6
s
8.3 Distinctness of reflected image R .6
i
8.4 Narrow-angle haze H .6
n
8.5 Wide-angle haze H .6
w
8.6 Diffuseness R .7
d
8.7 Directionality D .7
h
9 Test report.7
Annex A (informative) Precision and accuracy of goniophotometers .8
Bibliography.9
ISO 7759:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 7759 was prepared by Technical Committee ISO/TC 79, Light metals and their alloys, Subcommittee
SC 2, Organic and anodic oxidation coatings on aluminium.
This second edition cancels and replaces the first edition (ISO 7759:1983), which has been technically revised.
iv © ISO 2010 – All rights reserved
ISO 7759:2010(E)
Introduction
The visual appearance of metallic finishes is important commercially on metals for automotive, architectural,
and other uses where these metals undergo special finishing processes to produce the desired appearance.
For end-products which use such finished metals, it is important that parts placed together have the same
appearance. Specular reflectance is one of the properties measured, but additional measurements are usually
required to identify adequately the appearance of any metal surface. In the method described in this
International Standard, several important aspects of surface appearance are identified and can be measured.
Those surfaces having identical sets of numbers will normally have the same reflectance characteristics and
the same appearance (see References [1], [2] and [3]).
INTERNATIONAL STANDARD ISO 7759:2010(E)
Anodizing of aluminium and its alloys — Measurement of
reflectance characteristics of aluminium surfaces using a
goniophotometer or an abridged goniophotometer
1 Scope
This International Standard specifies a method for the measurement of the reflectance characteristics of high-
gloss anodized aluminium surfaces.
The method described is also suitable for the measurement of the reflectance characteristics of other high-
gloss metal surfaces.
The method is not suitable for diffuse-finish metal surfaces and does not measure colour.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
CIE
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.