EN ISO 11252:2004
(Main)Lasers and laser-related equipment - Laser device - Minimum requirements for documentation (ISO 11252:2004)
Lasers and laser-related equipment - Laser device - Minimum requirements for documentation (ISO 11252:2004)
This International Standard specifies the minimum documentation and marking and labelling information to be provided with laser devices (including laser diodes).
The documentation is presented on two levels: as a technical data sheet (Clause 5) and as an instruction manual (Clause 6).
This International Standard does not apply to laser products which incorporate laser devices.
Laser und Laseranlagen - Lasergerät - Mindestanforderungen an die Dokumentation (ISO 11252:2004)
Diese Internationale Norm legt die Mindestanforderungen für die Dokumentation, Kennzeichnung und Beschilderung fest, die Lasergeräten (einschließlich Laserdioden) beigefügt werden müssen.
Die Dokumentation wird in zwei Bereiche gegliedert: in das technische Datenblatt (Abschnitt 5) und in die Betriebsanleitung (Abschnitt 6).
Diese Internationale Norm gilt nicht für Laser-Einrichtungen, die Lasergeräte enthalten.
Sie gilt auch nicht für Lasergeräte, die vor der Veröffentlichung dieser Norm hergestellt wurden.
Anforderungen an Lärmschutz sind nicht enthalten. Diese Anforderungen sollen in einer späteren Änderung eingeführt werden.
Lasers et équipements associés aux lasers - Source laser - Exigences minimales pour la documentation (ISO 11252:2004)
Laserji in laserska oprema - Laserska naprava – Minimalne zahteve za dokumentacijo (ISO 11252:2004)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2005
1DGRPHãþD
SIST EN 31252:2000
Laserji in laserska oprema - Laserska naprava – Minimalne zahteve za
dokumentacijo (ISO 11252:2004)
Lasers and laser-related equipment - Laser device - Minimum requirements for
documentation (ISO 11252:2004)
Laser und Laseranlagen - Lasergerät - Mindestanforderungen an die Dokumentation
(ISO 11252:2004)
Lasers et équipements associés aux lasers - Source laser - Exigences minimales pour la
documentation (ISO 11252:2004)
Ta slovenski standard je istoveten z: EN ISO 11252:2004
ICS:
31.260 Optoelektronika, laserska Optoelectronics. Laser
oprema equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 11252
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2004
ICS 31.260 Supersedes EN 31252:1994
English version
Lasers and laser-related equipment - Laser device - Minimum
requirements for documentation (ISO 11252:2004)
Lasers et équipements associés aux lasers - Source laser - Laser und Laseranlagen - Lasergerät -
Exigences minimales pour la documentation (ISO Mindestanforderungen an die Dokumentation (ISO
11252:2004) 11252:2004)
This European Standard was approved by CEN on 14 November 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11252:2004: E
worldwide for CEN national Members.
Foreword
This document (EN ISO 11252:2004) has been prepared by Technical Committee ISO/TC 172
"Optics and optical instruments" in collaboration with Technical Committee CEN/TC 123 "Lasers
and laser-related equipment", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by May 2005, and conflicting national standards
shall be withdrawn at the latest by May 2005.
This document supersedes EN 31252:1994.
This document has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association, and supports essential requirements of EU
Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 11252:2004 has been approved by CEN as EN ISO 11252:2004 without any
modifications.
ANNEX ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37 EEC
This European Standard has been prepared under a mandate given to CEN by the European
Commission and the European Free Trade Association to provide a means of conforming to
Essential Requirements of the New Approach Directive 98/37 EEC.
Once this standard is cited in the Official Journal of the European Communities under that
Directive and has been implemented as a national standard in at least one Member State,
compliance with the normative clauses of this standard given in Table ZA. confers, within the
limits of the scope of this standard, a presumption of conformity with the corresponding Essential
Requirements of that Directive and associated EFTA regulations.
WARNING: Other requirements and other EU Directives may be applicable to the product(s)
falling within the scope of this standard.
INTERNATIONAL ISO
STANDARD 11252
Second edition
2004-11-15
Lasers and laser-related equipment —
Laser device — Minimum requirements
for documentation
Lasers et équipements associés aux lasers — Source laser —
Exigences minimales pour la documentation
Reference number
ISO 11252:2004(E)
©
ISO 2004
ISO 11252:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2004 – All rights reserved
ISO 11252:2004(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 2
4 Units . 2
5 Technical data sheet. 2
5.1 General. 2
5.2 Beam output characteristics. 2
5.3 Power supply. 2
5.4 Liquids and gases. 3
5.5 Environmental conditions. 3
5.6 Mechanical interfaces. 4
5.7 Safety. 4
6 Instruction manual . 4
7 Marking and labelling . 4
Annex A (informative) Model of data sheet. 5
Bibliography . 9
ISO 11252:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11252 was prepared by Technical Committee ISO/TC 172, Optics and photonics, Subcommittee SC 9,
Electro-optical systems.
This second edition cancels and replaces the first edition (ISO 11252:1993), which has been technically
revised.
iv © ISO 2004 – All rights reserved
ISO 11252:2004(E)
Introduction
This document is a type B1 standard as defined in ISO 12100-1.
The provisions of this document may be supplemented or modified by a type C standard.
NOTE For machines which are covered by the scope of a type C standard and which have been designed and built
according to the provisions of that standard, the provisions of that type C standard take precedence over the provisions of
this type B1 standard.
INTERNATIONAL STANDARD ISO 11252:2004(E)
Lasers and laser-related equipment — Laser device — Minimum
requirements for documentation
1 Scope
This International Standard specifies the minimum documentation and information for marking and labelling, to
be provided with laser devices (including laser diodes).
The documentation is presented on two levels: as a technical data sheet (Clause 5) and as an instruction
manual (Clause 6).
This International Standard does not apply to laser products which incorporate laser devices.
It also does not apply to laser devices manufactured before the date of publication of this document.
Requirements on noise are not included in this standard. These requirements will be included in a subsequent
amendment.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 11145, Optics and optical instruments — Lasers and laser-related equipment — Vocabulary and symbols
ISO 11146-1, Lasers and laser-related equipment — Test methods for laser beam widths, divergence angles
and beam propagation ratios — Part 1: Stigmatic and simple astigmatic beams
ISO 11146-2, Lasers and laser-related equipment — Test methods for laser beam widths, divergence angles
and beam propagation ratios — Part 2: General astigmatic beams
ISO 11554, Optics and optical instruments — Lasers and laser-related equipment — Test methods for laser
beam power, energy and temporal characteristics
ISO 11670, Lasers and laser-related equipment — Test methods for laser beam parameters — Beam
positional stability
ISO 12005, Lasers and laser-related equipment — Test methods for laser beam parameters — Polarization
ISO 12100-1, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic
terminology, methodology
ISO 13694, Optics and optical instruments — Lasers and laser-related equipment — Test methods for laser
beam power (energy) density distribution
ISO 13695, Optics and photonics — Lasers and laser-related equipment — Test methods for the spectral
characteristics of lasers
ISO 11252:2004(E)
ISO 15367-1, Lasers and laser-related equipment — Test methods for determination of the shape of a laser
beam wavefront — Part 1: Terminology and fundamental aspects
ISO 15367-2, Lasers and laser-related equipment — Test methods for determination of the shape of a las
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.