iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 14382:2005

(Main)

Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar

Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar

This document specifies constructional, functional, sizing, and testing requirements, also documentation and marking of gas safety shut-off devices used in the pressure regulating stations in accordance with EN 12186 or EN 12279:
-   for inlet pressures up to 100 bar and nominal diameters up to DN 400;
-   for an operating temperature range from -20 °C to +60 °C,
which operate with fuel gases of the 1st and 2nd family in accordance with EN 437 in transmission and distribution networks and also in commercial and industrial installations.
"Gas safety shut-off devices" will hereafter be called "SSDs" except in titles.
The harmonized part of this document deals with standard safety shut-off devices used in pressure regulating stations complying with EN 12186 or EN 12279. For standard safety shut-off devices integral strength type when used in pressure regulating stations complying with EN 12186 or EN 12279, Annex ZA lists all applicable Essential Requirements except the external resistance to environmental conditions where corrosion occurs.
This document considers the following classes of SSDs:
temperature classes:
-   class 1: operating temperature range from -10 °C to 60 °C;
-   class 2: operating temperature range from -20 °C to 60 °C;
functional classes:
-   class A: SSDs that close when damage to the pressure sensing element occurs (applicable to overpressure SSDs only) or when external power fails;
-   class B: SSDs that do not close when damage to the pressure sensing element occurs or are able to be opened automatically by the pressure control system (applicable to overpressure SSDs only).
SSDs complying with the requirements of this document may be declared as "in conformity with EN 14382" and bear the mark "EN 14382".
The material and functional requirements specified in this document may be applied to SSDs which use thermal energy or the effects of electrical energy to trip the operation of the closing member. For these SSDs the operational parameters are n

Sicherheitseinrichtungen für Gas-Druckregelanlagen und -einrichtungen - Gas-Sicherheitsabsperreinrichtungen für Betriebsdrücke bis 100 bar

Dieses Dokument legt Bauanforderungen, Funktionsanforderungen, Dimensionierung, Prüfung, Dokumentation und Kennzeichnung von Gas-Sicherheitsabsperreinrichtungen, die in den Druckregelanlagen nach EN 12186 und EN 12279 verwendet werden, fest für
-   Eingangsdrücke bis 100 bar und Nennweiten bis DN 400;
-   Betriebstemperaturen von -20 *C bis +60 *C,
soweit sie mit Brenngasen der 1. und 2. Familie nach EN 437 in Gasversorgungsnetzen wie auch in gewerblichen und industriellen Anlagen betrieben werden.
"Gas-Sicherheitsabsperreinrichtung" wird im Weiteren, außer in Überschriften, mit "SAE" abgekürzt.
Der harmonisierte Teil dieses Dokuments gilt für Sicherheitsabsperreinrichtungen, die in den Druckregelanlagen in Übereinstimmung mit den jeweils zutreffenden EN 12186 und EN 12279 verwendet werden. Für Sicherheitsabsperreinrichtungen mit einheitlichem Festigkeitsbereich, die in den Druckregelanlagen in Übereinstimmung mit den jeweils zutreffenden EN 12186 und EN 12279 verwendet werden, schließt die Tabelle ZA.1 im informativen Anhang ZA alle relevanten grundlegenden Anforderungen nach Anhang 1 der DGR ein, mit Ausnahme der Beständigkeit gegen Umwelteinflüsse im Korrosionsfall.
Dieses Dokument behandelt die folgenden Klassen von SAE:
Temperaturklassen:
-   Klasse 1: Betriebstemperaturbereich von -10 °C bis 60 °C;
-   Klasse 2: Betriebstemperaturbereich von -20 °C bis 60 °C.
Funktionsklassen:
-   Klasse A: Schließen bei Schaden an der Vergleichermembran (nur bei Überdruckabsicherung) oder im Falle eines Ausfalls der externen Energiequelle;
-   Klasse B: kein Schließen bei Schaden an der Vergleichermembran bzw. mögliches automatisches Öffnen, wenn der zu überwachende Druck durch die Druckregelung wieder unter den Ansprechdruck der SAE abgesenkt wurde (nur bei Überdruckabsicherung).
SAE, die den Anforderungen dieser Norm entsprechen, können als "in Übereinstimmung mit EN 14382" deklariert und mit der Kennzeichnung "EN 14382" versehen werden.

Dispositifs de sécurité pour postes et installations de détente-régulation de pression de gaz - Clapets de sécurité pour pressions amont jusqu'à 100 bar

Varnostne naprave za plinske regulacijske postaje in napeljave - Plinske varnostne zaporne naprave za vstopne tlake do 100 bar

General Information

Status
Withdrawn
Publication Date
08-Mar-2005
Withdrawal Date
17-Mar-2009
ICS
23.060.40 - Pressure regulators
Technical Committee
CEN/TC 235 - Gas pressure regulators and associated safety devices for use in gas transmission and distribution
Drafting Committee
CEN/TC 235 - Gas pressure regulators and associated safety devices for use in gas transmission and distribution
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
18-Mar-2009
Completion Date
18-Mar-2009
Directive
97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
Mandate
M/071 - Mandate to CEN for standardization in the field of Pressure equipment
Ref Project
SIST EN 14382:2005 - Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar

Relations

Replaces
EN 14382:2002 - Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar
Effective Date
22-Dec-2008
Merged Into
EN 14382:2005+A1:2009 - Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar
Effective Date
18-Jan-2023
Amended By
EN 14382:2005/prA1 - Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar
Effective Date
22-Dec-2008

Buy Standard

EN 14382:2005EN 14382:2005
PreviousNext
Standard
EN 14382:2005
English language
85 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 barVarnostne naprave za plinske regulacijske postaje in napeljave - Plinske varnostne zaporne naprave za vstopne tlake do 100 barDispositifs de sécurité pour postes et installations de détente-régulation de pression de gaz - Clapets de sécurité pour pressions amont jusqu'a 100 barSicherheitseinrichtungen für Gas-Druckregelanlagen und -einrichtungen - Gas-Sicherheitsabsperreinrichtungen für Betriebsdrücke bis 100 barTa slovenski standard je istoveten z:EN 14382:2005SIST EN 14382:2005en,fr,de23.060.40ICS:SIST EN 14382:20041DGRPHãþDSLOVENSKI
STANDARDSIST EN 14382:200501-junij-2005







EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14382
March 2005 ICS 23.060.40 Supersedes EN 14382:2002 English version
Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar
Dispositifs de sécurité pour postes et installations de détente-régulation de pression de gaz - Clapets de sécurité pour pressions amont jusqu'à 100 bar
Sicherheitseinrichtungen für Gas-Druckregelanlagen und -einrichtungen - Gas-Sicherheitsabsperreinrichtungen für Betriebsdrücke bis 100 bar This European Standard was approved by CEN on 30 December 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2005 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14382:2005: E



EN 14382:2005 (E) 2 Contents page Foreword.5 1 Scope.6 2 Normative references.7 3 Terms, definitions and symbols.8 3.1 Terms and definitions.8 3.2 Functional variables.13 3.3 Operating features.15 3.4 Further design terminology.16 4 Construction requirements.18 4.1 Basic requirements.18 4.1.1 General.18 4.1.2 Types of shut-off devices.19 4.1.3 End connections.19 4.1.4 Flange ratings.20 4.1.5 Nominal sizes and face-to-face dimensions.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 14382:2019(Main)
Gas safety shut-off devices for inlet pressure up to 10 MPa (100 bar)
SIST EN 14382:2019

This document specifies constructional, functional, testing marking and sizing requirements and documentation of gas safety shut-off devices:
-   for inlet pressures up to 100 bar and nominal diameters up to DN 400;
-   for an operating temperature range from -20 °C to +60 °C;
which operate with fuel gases of the 1st and 2nd family as defined in EN 437, used in the pressure regulating stations in accordance with EN 12186 or EN 12279, in transmission and distribution networks and also in commercial and industrial installations.
"Gas safety shut-off devices" will hereafter be called "SSDs" except in titles.
For standard safety shut-off devices when used in pressure regulating stations complying with EN 12186 or EN 12279, Annex ZA lists all applicable Essential Safety Requirements of Directive 2014/68/EU (PED).
This document considers the following temperature classes/types of SSDs:
-   temperature class 1: operating temperature range from -10 °C to 60 °C;
-   temperature class 2: operating temperature range from -20 °C to 60 °C;
-   functional class A: SSDs that close when damage to the pressure detecting element occurs or when external power fails and whose re-opening, is possible only manually;
-   functional class B: SSDs that do not close when damage to the pressure detecting element occurs but provide suitable and reliable protection and whose re-opening, is possible only manually;
-   type IS: (integral strength type);
-   type DS: (differential strength type).
SSDs complying with the requirements of this document may be declared as "in conformity with EN 14382" and bear the mark "EN 14382".
The material and functional requirements specified in this document may be applied to SSDs which use thermal energy or the effects of electrical energy to trip the operation of the closing member. For these SSDs the operational parameters are not specified in this document.
The SSD may incorporate a vent limiter, complying with the requirements in Annex J.
This standard for some paragraphs and sub clauses makes full reference to prEN 334:2016.
This document does not apply to:
-   SSDs upstream from/on/in domestic gas-consuming appliances which are installed downstream of domestic gas meters;
-   SSDs designed to be incorporated into pressure-regulating devices used in service lines  with volumetric flow rate ≤ 200 m3/h at normal conditions and inlet pressure ≤ 5 bar.
Continued integrity of safety shut-off devices is ensured by periodic functional checks. For periodic functional checks it is common to refer to national regulations/standards where existing or users/manufacturers practices.
This document considers the reaction of the SSDs functional class A to the specified reasonable expected failures in terms of "fail close" behaviour, but it should be consider that there are other types of failures whose consequences cannot bring to the same reactions (these risks are covered via redundancy as per EN 12186) and that residual hazards should be reduced by a suitable surveillance in use / maintenance.
In this document, both safety shut-off devices that can be classified as "safety accessories" by themselves according the Pressure Equipment Directive (2014/68/EU) as well as safety shut-off devices that can be used to provide the necessary pressure protection through redundancy (e.g. shutoff device integrated in a pressure regulator, shut-off device with a second shut-off device) are considered. Addition of environmental considerations;
The provisions in this document are in line with the state of art at the moment of writing.
This document does not intend to limit the improvement of actual provisions (materials, requirements, test methods, acceptance criteria, etc.) or the developing of new provisions for SSDs where they are suitable to ensure an equivalent level of reliability.

  • Standard
    78 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 334:2019(Main)
Gas pressure regulators for inlet pressure up to 10 MPa (100 bar)
SIST EN 334:2019

This European Standard specifies constructional, functional, testing, marking, sizing and documentation requirements of gas pressure regulators:
-   for inlet pressures up to 100 bar and nominal diameters up to DN 400;
-   for an operating temperature range from - 20  °C to +60 °C,
which operate with fuel gases of the 1st and 2nd  family as defined in EN 437:2003+A1:2009, used in the pressure regulating stations in accordance with EN 12186 or EN 12279, in transmission and distribution networks and also in commercial and industrial installations.
"Gas pressure regulators" hereafter will be called "regulators" except in the titles.
For standard regulators when used in pressure regulating stations complying with EN 12186 or EN 12279, the Annex ZA lists all applicable essential safety requirements of the European legislation on pressure equipment except external and internal corrosion resistance for applications in corrosive environment.
This document considers the following temperature classes/types of regulators:
-   temperature class 1: operating temperature range from −10 °C to 60 °C;
-   temperature class 2: operating temperature range from −20 °C to 60 °C;
-   type IS: (integral strength type);
-   type DS: (differential strength type).
This document applies to regulators which use the pipeline gas as a source of control energy unassisted by any external power source.
The regulator may incorporate a second regulator, used as monitor, complying with the requirements in this document.
The regulator may incorporate a safety shut off device (SSD) complying with the requirements of EN 14382.
The regulator may incorporate a creep (venting) relief device, complying with the requirements in Annex E and/or a vent limiter, complying with the requirements in Annex I.
This document does not apply to:
-   regulators upstream from/on/in domestic gas-consuming appliances which are installed downstream of domestic gas meters;
-   regulators designed to be incorporated into pressure control systems used in service lines ) with volumetric flow rate ≤ 200 m3/h at normal conditions and inlet pressure ≤ 5 bar;
-   regulators for which a specific document exists (e.g. EN 88-1 and EN 88-2, etc.);
-   industrial process control valves in accordance with EN 1349.
The normative Annex G of this document lists some suitable materials for pressure bearing parts, inner metallic partition walls, auxiliary devices, integral process and sensing lines, connectors and fasteners. Other materials may be used when complying with the restrictions given in Table 5.
Continued integrity of gas pressure regulators is ensured by suitable surveillance checks and maintenance. For periodic functional checks and maintenance it is common to refer to national regulations/standards where existing or users/manufacturers practices.
This document has introduced the reaction of the pressure regulators to the specified reasonable expected failures in terms of "fail close" and "fail open" pressure regulator types, but it should be considered that there are other types of failures whose consequences can bring to the same reactions (these risks are covered via redundancy as per EN 12186) and that residual hazards will be reduced by a suitable surveillance in use / maintenance.
In this document, both pressure regulators that can be classified as "safety accessories" by themselves (monitors) according to European legislation on pressure equipment as well as regulators that can be used to provide the necessary pressure protection through redundancy (e.g. pressure regulator with integrated safety shut-off device, pressure regulator + in-line monitor, pressure regulator + safety shut off device) are considered.
The provisions in this document are in line with the state of art at the moment of writing.

  • Standard
    148 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 334:2019/FprA1(Amendment)
Gas pressure regulators for inlet pressure up to 10 MPa (100 bar)
SIST EN 334:2019/oprA1:2023

This European Standard specifies constructional, functional, testing, marking, sizing and documentation requirements of gas pressure regulators:
-   for inlet pressures up to 100 bar and nominal diameters up to DN 400;
-   for an operating temperature range from - 20  °C to +60 °C,
which operate with fuel gases of the 1st and 2nd  family as defined in EN 437:2003+A1:2009, used in the pressure regulating stations in accordance with EN 12186 or EN 12279, in transmission and distribution networks and also in commercial and industrial installations.
"Gas pressure regulators" hereafter will be called "regulators" except in the titles.
For standard regulators when used in pressure regulating stations complying with EN 12186 or EN 12279, the Annex ZA lists all applicable essential safety requirements of the European legislation on pressure equipment except external and internal corrosion resistance for applications in corrosive environment.
This document considers the following temperature classes/types of regulators:
-   temperature class 1: operating temperature range from −10 °C to 60 °C;
-   temperature class 2: operating temperature range from −20 °C to 60 °C;
-   type IS: (integral strength type);
-   type DS: (differential strength type).
This document applies to regulators which use the pipeline gas as a source of control energy unassisted by any external power source.
The regulator may incorporate a second regulator, used as monitor, complying with the requirements in this document.
The regulator may incorporate a safety shut off device (SSD) complying with the requirements of EN 14382.
The regulator may incorporate a creep (venting) relief device, complying with the requirements in Annex E and/or a vent limiter, complying with the requirements in Annex I.
This document does not apply to:
-   regulators upstream from/on/in domestic gas-consuming appliances which are installed downstream of domestic gas meters;
-   regulators designed to be incorporated into pressure control systems used in service lines ) with volumetric flow rate ≤ 200 m3/h at normal conditions and inlet pressure ≤ 5 bar;
-   regulators for which a specific document exists (e.g. EN 88-1 and EN 88-2, etc.);
-   industrial process control valves in accordance with EN 1349.
The normative Annex G of this document lists some suitable materials for pressure bearing parts, inner metallic partition walls, auxiliary devices, integral process and sensing lines, connectors and fasteners. Other materials may be used when complying with the restrictions given in Table 5.
Continued integrity of gas pressure regulators is ensured by suitable surveillance checks and maintenance. For periodic functional checks and maintenance it is common to refer to national regulations/standards where existing or users/manufacturers practices.
This document has introduced the reaction of the pressure regulators to the specified reasonable expected failures in terms of "fail close" and "fail open" pressure regulator types, but it should be considered that there are other types of failures whose consequences can bring to the same reactions (these risks are covered via redundancy as per EN 12186) and that residual hazards will be reduced by a suitable surveillance in use / maintenance.
In this document, both pressure regulators that can be classified as "safety accessories" by themselves (monitors) according to European legislation on pressure equipment as well as regulators that can be used to provide the necessary pressure protection through redundancy (e.g. pressure regulator with integrated safety shut-off device, pressure regulator + in-line monitor, pressure regulator + safety shut off device) are considered.
The provisions in this document are in line with the state of art at the moment of writing.

  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14382:2019/FprA1(Amendment)
Gas safety shut-off devices for inlet pressure up to 10 MPa (100 bar)
SIST EN 14382:2019/kFprA1:2023

This document specifies constructional, functional, testing marking and sizing requirements and documentation of gas safety shut-off devices:
-   for inlet pressures up to 100 bar and nominal diameters up to DN 400;
-   for an operating temperature range from -20 °C to +60 °C;
which operate with fuel gases of the 1st and 2nd family as defined in EN 437, used in the pressure regulating stations in accordance with EN 12186 or EN 12279, in transmission and distribution networks and also in commercial and industrial installations.
"Gas safety shut-off devices" will hereafter be called "SSDs" except in titles.
For standard safety shut-off devices when used in pressure regulating stations complying with EN 12186 or EN 12279, Annex ZA lists all applicable Essential Safety Requirements of Directive 2014/68/EU (PED).
This document considers the following temperature classes/types of SSDs:
-   temperature class 1: operating temperature range from -10 °C to 60 °C;
-   temperature class 2: operating temperature range from -20 °C to 60 °C;
-   functional class A: SSDs that close when damage to the pressure detecting element occurs or when external power fails and whose re-opening, is possible only manually;
-   functional class B: SSDs that do not close when damage to the pressure detecting element occurs but provide suitable and reliable protection and whose re-opening, is possible only manually;
-   type IS: (integral strength type);
-   type DS: (differential strength type).
SSDs complying with the requirements of this document may be declared as "in conformity with EN 14382" and bear the mark "EN 14382".
The material and functional requirements specified in this document may be applied to SSDs which use thermal energy or the effects of electrical energy to trip the operation of the closing member. For these SSDs the operational parameters are not specified in this document.
The SSD may incorporate a vent limiter, complying with the requirements in Annex J.
This standard for some paragraphs and sub clauses makes full reference to prEN 334:2016.
This document does not apply to:
-   SSDs upstream from/on/in domestic gas-consuming appliances which are installed downstream of domestic gas meters;
-   SSDs designed to be incorporated into pressure-regulating devices used in service lines  with volumetric flow rate ≤ 200 m3/h at normal conditions and inlet pressure ≤ 5 bar.
Continued integrity of safety shut-off devices is ensured by periodic functional checks. For periodic functional checks it is common to refer to national regulations/standards where existing or users/manufacturers practices.
This document considers the reaction of the SSDs functional class A to the specified reasonable expected failures in terms of "fail close" behaviour, but it should be consider that there are other types of failures whose consequences cannot bring to the same reactions (these risks are covered via redundancy as per EN 12186) and that residual hazards should be reduced by a suitable surveillance in use / maintenance.
In this document, both safety shut-off devices that can be classified as "safety accessories" by themselves according the Pressure Equipment Directive (2014/68/EU) as well as safety shut-off devices that can be used to provide the necessary pressure protection through redundancy (e.g. shutoff device integrated in a pressure regulator, shut-off device with a second shut-off device) are considered. Addition of environmental considerations;
The provisions in this document are in line with the state of art at the moment of writing.
This document does not intend to limit the improvement of actual provisions (materials, requirements, test methods, acceptance criteria, etc.) or the developing of new provisions for SSDs where they are suitable to ensure an equivalent level of reliability.

  • Draft
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14382:2005/prA1(Amendment)
Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar
SIST EN 14382:2005/kprA1:2008

Tolerance of 9 months before UAP per CEN/TC 235 res. C03/2006.

  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 334:2005/prA1(Amendment)
Gas pressure regulators for inlet pressures up to 100 bar
SIST EN 334:2005/kprA1:2008

Tolerance of 9 months requested before UAP per CEN/TC 235 C02/2006.

  • Draft
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22435:2024(Main)
Gas cylinders - Cylinder valves with integrated pressure regulators - Specification and type testing (ISO 22435:2024)
kSIST FprEN ISO 22435:2024

This document specifies design, type test methods, marking and instruction requirements for cylinder valves with integrated pressure regulators (VIPRs) intended to be fitted to gas cylinders, pressure drums or tubes or used as a main valve for bundles of cylinders that convey compressed, liquefied or dissolved gases.
These are requirements for VIPRs that are in addition to those given in the relevant closure standard, for example, in ISO 10297 for cylinder valves, in ISO 17871 for quick-release cylinder valves, in ISO 17879 for self-closing cylinder valves or in ISO 23826 for ball valves. For ISO 17871, these requirements are only applicable to quick-release cylinder valves types B, C, D and E.
NOTE 1        If the pressure regulating system of a VIPR is acting as the primary valve operating mechanism, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826. This also includes designs where closure of the primary valve operating mechanism of a VIPR is obtained by closing the seat of the pressure regulating system.
NOTE 2        If the primary valve operating mechanism of a VIPR is located at the low-pressure side of the pressure regulating system, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826.
NOTE 3        The term “pressure receptacle” is used within this document to cover instances where no differentiation is necessary between gas cylinders, bundles of cylinders, pressure drums and tubes.
This document does not apply to VIPRs for
a)       medical applications (see ISO 10524-3);
b)       liquefied petroleum gas (LPG);
c)        cryogenic applications.
NOTE 4        Additional requirements for a VIPR with a residual pressure device (RPD) are specified in ISO 15996.
NOTE 5        Additional requirements for pressure relief valves can exist in international/regional regulations/ standards.

  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 17924:2023(Main)
Safety and control devices for burners and appliances burning gaseous and/or liquid fuels - Guidance on hydrogen specific aspects
SIST-TP CEN/TR 17924:2023

This document gives guidance on hydrogen specific safety, design, construction, and performance requirements and testing of safety, control or regulating devices (hereafter referred to as controls) for burners and appliances burning gases with hydrogen content.
The following hydrogen concentrations are covered in this document:
- H2NG (hydrogen in natural gas) blends of 20 % hydrogen; or
- 100 % hydrogen; or
- varying blends / admixtures to natural gas.
Furthermore, it identifies the expected revision needs of the existing CEN/TC 58 standards as well as the need of potential further new standardization deliverables.

  • Technical report
    73 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1643:2022(Main)
Safety and control devices for burners and appliances burning gaseous and/or liquid fuels - Valve proving systems for automatic shut-off valves
SIST EN 1643:2023

EN 13611:2019, Clause 1 is replaced by following:
This document specifies the safety, design, construction and performance requirements, and testing for valve-proving systems, hereafter referred to as “VPS”, intended for use with gas burners and gas-burning appliances burning one or more gaseous fuels.
This document applies to all types of VPS used for the automatic detection of leakage in a gas burner section having at least two automatic shut-off valves, and which give a signal if the leakage of one of the valves, the piping in-between the valves or of the VPS itself and its components exceeds the detection limit.
This document applies to VPS for gases with a maximum inlet pressure up to and including 500 kPa.
This document does not apply to VPSs for use in explosive atmospheres.
This document is applicable to AC and DC supplied VPS (for VPS supplied by stand-alone battery system, battery systems for mobile applications, or VPS which are intended to be connected to DC supply networks, see Annex I).

  • Standard
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12067-2:2022(Main)
Safety and control devices for burners and appliances burning gaseous or liquid fuels - Control functions in electronic systems - Part 2: Fuel/air ratio control/supervision of the electronic type
SIST EN 12067-2:2023

EN 13611:2019, Clause 1 is replaced by the following:
This document specifies the safety, design, construction and performance requirements, and testing for electronic fuel/air ratio control systems (ERC), electronic fuel/air ratio supervision systems (ERS) and electronic fuel/air ratio trim systems (ERT) intended for use with burners and appliances burning gaseous or liquid fuels. It also describes the procedures for evaluating these requirements and specifies information necessary for installation and use.
This document is applicable to:
-   closed loop fuel/air ratio control systems, see 3.101;
-   fuel/air ratio supervision systems, see 3.102;
-   closed loop fuel/air ratio trim systems, see 3.103;
and does not differentiate into classification by heat input.
NOTE   The documents for burners, appliances or processes which use ERC, ERS or ERT can override the requirements of this document.

  • Standard
    70 pages
    English language
    sale 10% off
    e-Library read for
    1 day