prEN 15630

Machines and plants for mining and tooling of natural stone - Safety - Requirements for gantry-type and cut-to-size saws

Part 6 of this European Standard defines specific concepts and techniques concerning the design, construction and maintenance as guidance for the designers in achieving safety for surfacing machines (grinding, polishing, calibrating, bush hammering, flaming, sand blasting machines). It only applies in compliance with part 1 of this European standard.

Maschinen und Anlagen zur Gewinnung und Bearbeitung von Naturstein — Sicherheit — Anforderungen für Brücken- und Aufteilsägen

Machines et installations d'extraction et d'usinage des pierres naturelles — Sécurité — Exigences relatives aux débiteuses-moulureuses à pont

Stroji in obrati za miniranje in obdelavo naravnega kamna - Varnost - Zahteve za mostovne žage in žage za razrezovanje po meri (gantry-type in cut-to-size)

General Information

• Status: Not Published
• ICS: 25.080.60 - Sawing machines
• ICS: 73.120 - Equipment for processing of minerals
• Technical Committee: CEN/TC 151 - Construction equipment and building material machines - Safety
• Drafting Committee: CEN/TC 151/WG 11 - Machines and plants for mining and tooling of natural stone - Safety
• Current Stage: 5098 - Decision to abandon - Formal Approval
• Start Date: 06-Nov-2009
• Completion Date: 06-Nov-2009
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Directive: 98/37/EC - Machinery
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Mandate: M/BC/CEN/88/13 - Standardization request to CEN/CENELEC relating to machinery
• Ref Project: oSIST prEN 15630:2007 - Machines and plants for mining and tooling of natural stone - Safety - Requirements for gantry-type and cut-to-size saws

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 15630:2007
01-junij-2007
Stroji in obrati za miniranje in obdelavo naravnega kamna - Varnost - Zahteve za
mostovne žage in žage za razrezovanje po meri (gantry-type in cut-to-size)
Machines and plants for mining and tooling of natural stone - Safety - Requirements for
gantry-type and cut-to-size saws
Maschinen und Anlagen zur Gewinnung und Bearbeitung von Naturstein - Sicherheit -
Anforderungen für Brücken und Aufteilsägen
Machines et installations d'extraction et d'usinage des pierres naturelles - Sécurité -
Exigences relatives aux débiteuses-moulureuses a pont
Ta slovenski standard je istoveten z: prEN 15630
ICS:
25.080.60 Strojne žage Sawing machines
73.120 Oprema za predelavo rudnin Equipment for processing of
minerals
oSIST prEN 15630:2007 en;fr;de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
DRAFT
prEN 15630
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2007
ICS 25.080.60; 73.120

English Version
Machines and plants for mining and tooling of natural stone -
Safety - Requirements for gantry-type and cut-to-size saws
Machines et installations d'extraction et d'usinage des Maschinen und Anlagen zur Gewinnung und Bearbeitung
pierres naturelles - Sécurité - Exigences relatives aux von Naturstein - Sicherheit - Anforderungen für Brücken-
débiteuses-moulureuses à pont und Aufteilsägen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 151.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15630:2007: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------
prEN 15630:2007 (E)
Contents
Foreword.3
Introduction .4
1 Scope.4
2 Normative references.5
3 Terms and definitions – Symbols and abbreviated terms.6
3.1 Gantry-type and cut-to-size saw .6
3.2 Types of gantry-type and cut-to-size saws .6
3.3 Illustration of the different types of gantry-type and cut-to-size saws .7
3.4 Other terms.9
4 List of significant hazards .9
5 Safety requirements and/or protective measures.10
5.1 Mechanical hazards.
...