EN ISO 16070:2005
(Main)Petroleum and natural gas industries - Downhole equipment - Lock mandrels and landing nipples (ISO 16070:2005)
Petroleum and natural gas industries - Downhole equipment - Lock mandrels and landing nipples (ISO 16070:2005)
ISO 16070:2005 provides the requirements for lock mandrels and landing nipples within the production/injection conduit for the installation of flow control or other equipment used in the petroleum and natural gas industries. ISO 16070:2005 includes the interface connections to the flow control or other equipment, but does not cover the connections to the well conduit.
Erdöl- und Erdgasindustrie - Bohrloch-Ausrüstung - Abhängestücke und Landenippel (ISO 16070:2005)
Industries du pétrole et du gaz naturel - Equipement de fond de trou - Mandrins à clé d'ancrage et sièges d'ancrage (ISO 16070:2005)
Industrija za predelavo nafte in zemeljskega plina – Oprema za vrtine – Zaklepna vpenjala in pristajalni prijemki (ISO 16070:2005)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2006
Industrija za predelavo nafte in zemeljskega plina – Oprema za vrtine – Zaklepna
vpenjala in pristajalni prijemki (ISO 16070:2005)
Petroleum and natural gas industries - Downhole equipment - Lock mandrels and landing
nipples (ISO 16070:2005)
Erdöl- und Erdgasindustrie - Bohrloch-Ausrüstung - Abhängestücke und Landenippel
(ISO 16070:2005)
Industries du pétrole et du gaz naturel - Equipement de fond de trou - Mandrins a clé
d'ancrage et sieges d'ancrage (ISO 16070:2005)
Ta slovenski standard je istoveten z: EN ISO 16070:2005
ICS:
75.180.10 Oprema za raziskovanje in Exploratory and extraction
odkopavanje equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 16070
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2005
ICS 75.180.10 Supersedes EN ISO 16070:2001
English Version
Petroleum and natural gas industries - Downhole equipment -
Lock mandrels and landing nipples (ISO 16070:2005)
Industries du pétrole et du gaz naturel - Equipement de Erdöl- und Erdgasindustrie - Bohrloch-Ausrüstung -
fond de trou - Mandrins à clé d'ancrage et sièges d'ancrage Abhängestücke und Landenippel (ISO 16070:2005)
(ISO 16070:2005)
This European Standard was approved by CEN on 26 September 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16070:2005: E
worldwide for CEN national Members.
Foreword
This document (EN ISO 16070:2005) has been prepared by Technical Committee ISO/TC 67
"Materials, equipment and offshore structures for petroleum and natural gas industries" in
collaboration with Technical Committee CEN/TC 12 "Materials, equipment and offshore
structures for petroleum, petrochemical and natural gas industries", the secretariat of which is
held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by June 2006, and conflicting national
standards shall be withdrawn at the latest by June 2006.
This document supersedes EN ISO 16070:2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 16070:2005 has been approved by CEN as EN ISO 16070:2005 without any
modifications.
INTERNATIONAL ISO
STANDARD 16070
Second edition
2005-12-15
Petroleum and natural gas industries —
Downhole equipment — Lock mandrels
and landing nipples
Industries du pétrole et du gaz naturel — Équipement de fond de
trou — Mandrins à clé d'ancrage et sièges d'ancrage
Reference number
ISO 16070:2005(E)
©
ISO 2005
ISO 16070:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2005 – All rights reserved
ISO 16070:2005(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 3
4 Abbreviated terms . 4
5 Functional specification. 5
5.1 General. 5
5.2 Functional characteristics of lock mandrels and landing nipples . 5
5.3 Well parameters . 5
5.4 Operational parameters . 5
5.5 Environmental compatibility. 6
5.6 Compatibility with the related well equipment . 6
5.7 Quality documentation. 6
5.8 Design validation . 6
6 Technical specification . 7
6.1 General. 7
6.2 Technical characteristics of lock mandrels and landing nipples . 7
6.3 Design criteria . 7
6.4 Design verification. 9
6.5 Design validation . 10
6.6 Design changes . 12
6.7 Functional test parameters. 12
7 Supplier/manufacturer requirements. 12
7.1 Documentation and data control. 12
7.2 User/purchaser documentation. 13
7.3 Product identification. 14
7.4 Quality control. 14
7.5 Functional testing. 21
8 Repair. 22
Annex A (informative) Example of landing nipple validation test dimensional check sheet . 23
Bibliography . 24
ISO 16070:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 16070 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures
for petroleum, petrochemical and natural gas industries, Subcommittee SC 4, Drilling and production
equipment.
This second edition cancels and replaces the first edition (ISO 16070:2001), which has been technically
revised.
iv © ISO 2005 – All rights reserved
ISO 16070:2005(E)
Introduction
This International Standard has been developed by users/purchasers and suppliers/manufacturers of lock
mandrels and landing nipples intended for use in the petroleum and natural gas industry worldwide. This
International Standard is intended to give requirements and information to both parties in the selection,
manufacture, testing and use of lock mandrels and landing nipples. Furthermore, this International Standard
addresses the minimum requirements with which the supplier/manufacturer is to comply so as to claim
conformity to this International Standard.
This International Standard has been structured to allow for grades of increased requirements in quality
documentation and design validation. These variations allow the user/purchaser to select the grade required
for a specific application.
There are two quality documentation grades which provide the user/purchaser the choice of requirements to
meet specific preference or application. Quality documentation grade Q2 is the minimum grade of
documentation offered by this International Standard. Grade Q1 provides additional material documentation.
There are three design validation grades which provide the user/purchaser the choice of requirements to meet
specific preference or application. Design validation grade V3 is the minimum grade and represents
equipment where the validation method has been defined by the supplier/manufacturer. The complexity and
severity of the validation testing increases as the grade number decreases.
Users of this International Standard should be aware that requirements above those outlined in this
International Standard may be needed for individual applications. This International Standard is not intended
to inhibit a supplier/manufacturer from offering, or the user/purchaser from accepting, alternative equipment or
engineering solutions. This may be particularly applicable where there is innovative or developing technology.
Where an alternative is offered, the supplier/manufacturer
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.