EN 1434-6:2015

Heat meters - Part 6: Installation, commissioning, operational monitoring and maintenance

This European Standard specifies commissioning, operational monitoring and maintenance and applies to heat meters. Heat meters are instruments intended for measuring the energy which in a heat-exchange circuit is absorbed (cooling) or given up (heating) by a liquid called the heat-conveying liquid. The heat meter indicates the quantity of heat in legal units.
Electrical safety requirements are not covered by this European Standard.
Pressure safety requirements are not covered by this European Standard.
Surface mounted temperature sensors are not covered by this European Standard.
This standard covers meters for closed systems only, where the differential pressure over the thermal load is limited.

Wärmezähler - Teil 6: Einbau, Inbetriebnahme, Überwachung und Wartung

Diese Europäische Norm legt die Inbetriebnahme, die Überwachung und die Wartung von Wärmezählern fest. Wärmezähler sind Geräte, die dazu dienen, die Energiemenge zu messen, die in einem Wärmetauscherkreislauf durch eine als Wärmeträgerflüssigkeit bezeichnete Flüssigkeit aufgenommen (Kühlen) oder abgegeben (Heizen) wird. Der Wärmezähler zeigt die Wärmemenge in gesetzlichen Einheiten an.
Elektrische Sicherheitsanforderungen werden in dieser Europäischen Norm nicht behandelt.
Den Druck betreffende Sicherheitsanforderungen werden in dieser Europäischen Norm nicht behandelt.
Oberflächenmontierte Temperaturfühler werden in dieser Europäischen Norm nicht behandelt.
Die vorliegende Norm behandelt ausschließlich Zähler für geschlossene Systeme, in denen der Differenz-druck am Wärmeüberträger begrenzt ist.

Compteurs d'énergie thermique - Partie 6: Installation, mise en service, surveillance de fonctionnement et maintenance

La présente Norme européenne spécifie l'installation, la mise en service, à la surveillance de fonctionnement et la maintenance et s'applique aux compteurs d'énergie thermique. Les compteurs d'énergie thermique sont des instruments destinés à mesurer l'énergie thermique qui, dans un circuit d'échange thermique, est absorbée (refroidissement) ou cédée (chauffage) par un liquide appelé « liquide caloporteur ». Le compteur d'énergie thermique fournit la quantité d'énergie thermique en unités de mesure légales.
La présente Norme européenne ne traite pas des prescriptions de sécurité électrique.
La présente Norme européenne ne traite pas des prescriptions de sécurité relative à la pression.
La présente Norme européenne ne traite pas des sondes de température montées en surface.
La présente norme couvre les compteurs pour les systèmes fermés uniquement, où la pression différentielle dans la charge thermique est limitée.

Merilniki toplote - 6. del: Vgradnja, zagon, nadzor in vzdrževanje

Ta evropski standard določa vgradnjo, zagon, nadzor in vzdrževanje ter se uporablja za toplotne števce, tj. instrumente, ki so namenjeni za merjenje toplote, ki jo v krogotoku toplotne izmenjave absorbira (hlajenje) ali oddaja (ogrevanje) tekočina, imenovana tekočina za prenos toplote. Toplotni števec podaja toploto v predpisanih enotah. Ta evropski standard ne zajema električnih varnostnih zahtev. Ta evropski standard ne zajema tlačnih varnostnih zahtev. Ta evropski standard ne zajema površinsko nameščenih senzorjev temperature. Ta standard zajema samo števce za zaprte sisteme, kjer je diferencialni tlak nad toplotno obremenitvijo omejen.

General Information

• Status: Withdrawn
• Publication Date: 03-Nov-2015
• Withdrawal Date: 12-Feb-2019
• ICS: 17.200.10 - Heat. Calorimetry
• Technical Committee: CEN/TC 176 - Heat meters
• Drafting Committee: CEN/TC 176/WG 2 - Heat Meters - Requirements, test methods and technical editing
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 13-Feb-2019
• Directive: 2004/22/EC - Directive 2004/22/EC of the European Parliament and of the Council of 31 March 2004 on measuring instruments
• Directive: 2014/32/EU - Directive 2014/32/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of measuring instruments
• Mandate: M/347 - Programming mandate to CEN, CENELEX and ETSI relating to measuring instruments
• Mandate: M/374 - Mandate to CEN and CENELEC for standards in the field of measuring instruments
• Mandate: M/441 - Standardisation mandate to CEN, CENELEC and ETSI in the field of measuring instruments for the development of an open architecture for utility meters involving communication protocols enabling interoperability
• Mandate: M/541 - [C(2015)8558] Standardization request in support of the implementation of Directive 2014/32/EU on measuring instruments
• Ref Project: SIST EN 1434-6:2016 - Heat meters - Part 6: Installation, commissioning, operational monitoring and maintenance

Relations

• Replaces: EN 1434-6:2007 - Heat meters - Part 6: Installation, commissioning, operational monitoring and maintenance
• Effective Date: 11-Nov-2015
• Merged Into: EN 1434-6:2015+A1:2019 - Thermal energy meters - Part 6: Installation, commissioning, operational monitoring and maintenance
• Effective Date: 19-Jan-2023
• Amended By: EN 1434-6:2015/prA1 - Thermal energy meters - Part 6: Installation, commissioning, operational monitoring and maintenance
• Effective Date: 04-Apr-2017

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Merilniki toplote - 6. del: Vgradnja, zagon, nadzor in vzdrževanjeWärmezähler - Teil 6: Einbau, Inbetriebnahme, Überwachung und WartungCompteurs d'énergie thermique - Partie 6 : Installation, mise en service, surveillance et maintenanceHeat meters - Part 6: Installation, commissioning, operational monitoring and maintenance17.200.10Toplota. KalorimetrijaHeat. CalorimetryICS:Ta slovenski standard je istoveten z:EN 1434-6:2015SIST EN 1434-6:2016en,fr,de01-januar-2016SIST EN 1434-6:2016SLOVENSKI
STANDARDSIST EN 1434-6:20071DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1434-6
November
t r s w ICS
s yä t r rä s r Supersedes EN
s v u væ xã t r r yEnglish Version
Heat meters æ Part
xã Installationá commissioningá operational monitoring and maintenance Compteurs d 5énergie thermique æ Partie
xã Installationá mise en serviceá surveillance de fonctionnement et maintenance
Wärmezähler æ Teil
xã Einbauá Inbetriebnahmeá Überwachung und Wartung This European Standard was approved by CEN on
w September
t r s wä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey andUnited Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s w CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s v u væ xã t r s w ESIST EN 1434-6:2016

Heat meter installation . 9 Annex B (informative)
Heat meter operational monitoring and maintenance . 19 Annex C (informative)
Suggested gauge for checking the dimensions of installed temperature sensor pockets . 22 Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 2004/22/EC, MID . 23 Bibliography . 24
1) EN 1434-3 is maintained by CEN/TC 294.
3 5 10 20 30 40 50 60 0,5 0,2 0,2 0,1 0,1 0,1 0 0 0 1 0,5 0,4 0,3 0,2 0,1 0,1 0,1 0,1 2 0,9 0,7 0,5 0,3 0,2 0,2 0,1 0,1 3 1,4 1,1 0,8 0,5 0,3 0,2 0,2 0,2 4 1,8 1,5 1,0 0,6 0,4 0,3 0,3 0,2 5 2,3 1,9 1,3 0,8 0,5 0,4 0,3 0,3 6 2,7 2,2 1,5 0,9 0,6 0,5 0,4 0,3 7 3,2 2,6 1,9 1,1 0,7 0,6 0,5 0,4 8 3,6 3,0 2,0 1,2 0,9 0,7 0,5 0,4 9 4,1 3,3 2,3 1,4 1,0 0,7 0,6 0,5 10 4,5 4,0 2,5 1,5 1,1 0,8 0,7 0,5 The values are shown as fraction of the maximum permissible error for the calculator. The values below the marked line are higher than 1/3rd of the maximum permissible error for the heat calculator. If the resulting error is higher than 1/3rd of the maximum permissible error, it is recommended to change the installation to have smaller differential pressure. NOTE In cases where flows from two different loads with different temperatures (e.g. for space heating and domestic warm water) are merged together just before the temperature sensor, the optimum position for the sensor is after the flow sensor. 4.1.3 For bifunctional meters for change-over systems between heating and cooling additional requirements are necessary to ensure the correct switching over function between the heating and cooling register. These requirements are: — the lowest operating temperature in the inlet pipe at heating conditions shall be at least 3 °C higher than any specified optional switching over temperature hc, SIST EN 1434-6:2016
...