prEN 17318-3
(Main)Railway applications - Infrastructure - Plastic sleepers and bearers - Part 3: Material characteristics
Railway applications - Infrastructure - Plastic sleepers and bearers - Part 3: Material characteristics
This part of the EN xxxxx series specifies the characteristics of sleepers and bearers made from plastic
or reinforced plastic materials. It applies to sleepers or bearers for railway infrastructure.
Bahnanwendungen - Infrastruktur - Gleis- und Weichenschwellen aus Kunststoff - Teil 3: Materialeigenschaften
Applications ferroviaires - Infrastructure - Traverses et supports en plastique - Partie 3 : Caractéristiques des matériaux
Železniške naprave - Infrastruktura - Plastični pragi in kretniški plastični pragi - 3. del: Lastnosti materiala
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 17318-3:2019
01-februar-2019
äHOH]QLãNHQDSUDYH,QIUDVWUXNWXUD3ODVWLþQLSUDJLLQNUHWQLãNLSODVWLþQLSUDJL
GHO/DVWQRVWLPDWHULDOD
Railway applications - Infrastructure - Plastic sleepers and bearers - Part 3: Material
characteristics
Bahnanwendungen - Infrastruktur - Gleis- und Weichenschwellen aus Kunststoff - Teil 3:
Materialeigenschaften
Applications ferroviaires - Infrastructure - Traverses et supports en plastique - Partie 3 :
Caractéristiques des matériaux
Ta slovenski standard je istoveten z: prEN 17318-3
ICS:
45.080 7UDþQLFHLQåHOH]QLãNLGHOL Rails and railway
components
oSIST prEN 17318-3:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 17318-3:2019
---------------------- Page: 2 ----------------------
oSIST prEN 17318-3:2019
DRAFT
EUROPEAN STANDARD
prEN 17318-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2018
ICS 45.080
English Version
Railway applications - Infrastructure - Plastic sleepers and
bearers - Part 3: Material characteristics
Applications ferroviaires - Infrastructure - Traverses et Bahnanwendungen - Infrastruktur - Gleis- und
supports en plastique - Partie 3 : Caractéristiques des Weichenschwellen aus Kunststoff - Teil 3:
matériaux Materialeigenschaften
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 256.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 17318-3:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 17318-3:2019
prEN 17318-3:2018 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Required material characteristics . 6
4.1 Resistance . 6
4.1.1 Chemical compatibility . 6
4.1.2 Environmental resistance . 6
4.2 Environmental compatibility . 7
4.3 Mech
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.