EN 1944:1996
(Main)Self-adhesive tapes - Measurement of unwind adhesion at low speed
- BACK
- 13-Feb-1996
- 30-Aug-1996
- 83.180
- CEN/TC 193
Self-adhesive tapes - Measurement of unwind adhesion at low speed
The standard specifies a method to measure the force required to unwind a roll of adhesive tape at low speed under standard test conditions.
Klebebänder - Messung der Abrollkraft bei niedriger Geschwindigkeit
Diese Norm legt ein Verfahren zum Messen der Kraft, die erforderlich ist, um eine Klebebandrolle mit niedriger Geschwindigkeit unter Normprüfbedingungen abzuwickeln.
Rubans auto-adhésifs - Mesure de la force de déroulement à faible vitesse
La présente norme européenne prescrit une méthode pour mesurer la force nécessaire pour dérouler un rouleau de ruban adhésif à faible vitesse dans des conditions spécifiées.
Samolepilni trakovi - Merjenje lepilne sile pri počasnem odvijanju
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.XKlebebänder - Messung der Abrollkraft bei niedriger GeschwindigkeitRubans auto-adhésifs - Mesure de la force de déroulement a faible vitesseSelf-adhesive tapes - Measurement of unwind adhesion
...
This May Also Interest You
This document specifies methods for determining the pot life of multi-part adhesives, in order to be able to determine whether the pot life conforms to the minimum specified working life required of an adhesive.
The different methods described in this document to measure the property do not necessarily provide identical results.
The test methods described are suitable for assessing all multi–part adhesives, and especially epoxy based and polyurethane based adhesives, but they are not suitable for some acrylic-based adhesives.
NOTE 1 Some of the methods described in this document can also be suitable for determination of working life of one-part adhesives that react to humidity (e.g. PUR prepolymers).
NOTE 2 This document can also be used for assessing non-structural adhesives.
- Standard17 pagesEnglish languagesale 10% offe-Library read for×1 day
- 06-Feb-2024
- 83.180
- CEN/TC 193
This document provides guidelines describing the adhesive bonding quality requirements suitable for use by adhesive user-companies utilizing adhesive bonding as a means of fabrication. In particular, the guidelines define various approaches to meeting quality requirements for fabrication and reporting procedures, both in workshops and on site. These guidelines aim to convey the importance of maintaining quality standards in fabrication and reporting procedures, keeping records and thus enabling documentation to provide the basis for risk evaluation of adhesively bonded structures in service and in use.
These guidelines have been prepared such that:
a) they are independent of the type of adhesively bonded structure;
b) they are independent of adhesive user-companies’ and suppliers’ product recommendations;
c) they define the quality requirements for adhesive bonding in terms of fabrication and reporting procedures, both in workshops and on site;
d) they can be used as the basis for risk evaluation of adhesively bonded structures in service and in use;
e) they can be used as a basis for assessing a fabricator's capability to produce adhesively bonded structures fulfilling specified quality requirements when they are detailed in one or more of the following:
— a contract between the parties involved;
— an application standard;
— a regulatory statement.
The guidelines contained within this document can be adopted in full or selectively chosen by the adhesive user to suit the structure concerned. The guidelines provide a flexible framework for the control of adhesive bonding activities in the following cases.
Case 1
The provision of specific requirements for adhesive bonding in contracts that require the adhesive user to have a quality system other than ISO 9001.
Case 2
The provision of specific requirements for adhesive bonding as guidance to an adhesive user developing a quality system.
Case 3
The provision of specific requirements for references in application standards that uses adhesive bonding as part of its requirements or in a contract between relevant parties.
Case 4
The provision of a framework for fabrication and reporting procedures to a quality standard, suitable in particular as a basis for the risk evaluation of adhesively bonded structures.
- Standard111 pagesEnglish languagesale 10% offe-Library read for×1 day
- 29-Aug-2023
- 83.180
- CEN/TC 193
This document specifies the individual measurements of notches. It assigns specific codes used to label notched tools according to the measurements and tolerances specified in this document.
- Standard18 pagesEnglish languagesale 10% offe-Library read for×1 day
- 06-Jun-2023
- 83.180
- CEN/TC 193
This document specifies a method of determining the ability of adhesive bonds to resist static load. It is applicable to adhesives used in load bearing timber structures.
It is applicable for the following applications:
a) for assessing the compliance of adhesives according to EN 301, EN 15425, EN 16254, EN 17334 and EN 17418;
b) for assessing the suitability and quality of adhesives for load-bearing timber structures;
c) for assessing the effect on the bond strength resulting from constant load at different climate conditions.
This method is intended primarily to obtain performance data for the classification of adhesives for load bearing timber structures according to their suitability for use in defined climatic environments.
This method is not intended to provide data for structural design and does not necessarily represent the performance of the bonded member in service.
- Standard20 pagesEnglish languagesale 10% offe-Library read for×1 day
- 25-Apr-2023
- 83.180
- CEN/TC 193
This document specifies a method for determining the influence of shear strength in crosswise gluing by wood shrinkage under drying conditions.
It is applicable for the following applications:
a) for assessing the compliance of adhesives with EN 301, EN 15425, EN 16254, EN 17334 and EN 17418;
b) for assessing the suitability and quality of adhesives for load-bearing timber structures;
c) for determining if the adhesive is capable of withstanding stresses due to wood shrinkage without unacceptable loss of strength.
This test is intended primarily to obtain performance data for the classification of adhesives for load-bearing timber structures according to their suitability for use in defined climatic environments. This test is carried out on Norway spruce (Picea abies L.).
This method is not intended to provide data for structural design and does not necessarily represent the performance of the bonded member in service.
- Standard14 pagesEnglish languagesale 10% offe-Library read for×1 day
- 14-Feb-2023
- 83.180
- CEN/TC 193
This document specifies a method for determining the effect on bond strength of damage to wood fibres caused by the action of acids from the adhesive or primer used in the gluing process during climatic cycling.
It is applicable to the following applications:
a) for assessing the compliance of adhesives with EN 301, EN 15425 and EN 16254;
b) for assessing the suitability and quality of adhesives for load-bearing timber structures;
c) for determining if the adhesive after bonding has a damaging influence on the strength of the wood due to chemical action.
This test is intended primarily to obtain performance data for the classification of adhesives for load-bearing timber structures according to their suitability for use in defined climatic environments. This test is carried out on Norway spruce (Picea abies L.) or Beech (Fagus sylvatica L.).
This method is not intended to provide data for structural design and does not necessarily represent the performance of the bonded member in service.
- Standard12 pagesEnglish languagesale 10% offe-Library read for×1 day
- 14-Feb-2023
- 83.180
- CEN/TC 193
This document specifies a method for determining the working life for adhesives mixed with hardener for load-bearing timber structures, by a viscosity test.
This method does not apply to determining the working life of a multi-component adhesive whose actual working life is very short.
This document is only intended for obtaining a reliable basis for comparison between adhesives. The method gives results which cannot be applied to the safe manufacture of timber structures without modifications for the influences of factory temperature and relative air humidity.
- Standard9 pagesEnglish languagesale 10% offe-Library read for×1 day
- 14-Feb-2023
- 83.180
- CEN/TC 193
This document specifies a method for determining the resistance to delamination in glue lines.
It is applicable to the following applications:
a) for assessing the compliance of adhesives with EN 301, EN 15425, EN 16254, EN 17334 and EN 17418;
b) for assessing the suitability and quality of adhesives for load-bearing timber structures;
c) for comparing the effects on the bond strength resulting from the choice of bonding conditions, from different climatic conditioning and from the treatment of the test pieces before and after bonding.
This test does not apply to modified and stabilized wood with strongly reduced swelling and shrinkage properties, such as acetylated wood, heat-treated wood and polymer impregnated wood.
This test is intended primarily to obtain performance data for the classification of adhesives for load-bearing timber structures according to their suitability for use in defined climatic environments.
This method is not intended to provide data for structural design and does not necessarily represent the performance of the bonded member in service.
- Standard14 pagesEnglish languagesale 10% offe-Library read for×1 day
- 14-Feb-2023
- 83.180
- CEN/TC 193
This document establishes a classification for one component polyurethane (PUR) adhesives according to their suitability for use in load-bearing timber products in defined climatic exposure conditions, and specifies performance requirements for such adhesives for the factory manufacture or factory-like manufacturing of load-bearing timber products only.
It also classifies “adhesive product lines” where all the products within the line have the same chemical composition except for a different amount of catalyst.
This document only specifies the performance of adhesives for use in an environment corresponding to the defined conditions.
The performance requirements of this document are applicable to the adhesives only, not to the manufactured timber products. This document does not cover the performance of adhesives for on-site gluing (except for factory-like conditions) or the production of wood-based panels, except solid wood panels, or modified and stabilized wood with considerably reduced swelling and shrinkage properties, e.g. acetylated wood, heat treated wood and polymer impregnated wood.
This document is primarily intended for use by adhesive manufacturers and for use in timber products bonded with adhesives, to assess or control the quality of adhesives. The requirements are applicable to the type testing of the adhesives. Production control activities are outside the scope of this document.
Adhesives meeting the requirements of this document are adequate for use in load-bearing timber products, provided that the bonding process has been carried out according to an appropriate product standard.
This document does not address the classification and use of adhesives in combination with the spraying of water before or during the bonding process; see informative Annex C of this document.
This does neither allow nor forbid the use of adhesives in combination with the spraying of water.
- Standard24 pagesEnglish languagesale 10% offe-Library read for×1 day
- 14-Feb-2023
- 83.180
- CEN/TC 193
This document establishes a classification for emulsion polymer isocyanate (EPI) adhesives according to their suitability for use in load-bearing timber products in defined climatic exposure conditions, and specifies performance requirements for such adhesives for the industrial manufacture of load-bearing timber products only.
The performance requirements of this document are applicable to the adhesives only, not to the timber products. This document does not cover the performance of adhesives for on-site gluing (except for factory-like conditions) or the production of wood-based panels, except solid wood panels, or modified and stabilized wood with considerably reduced swelling and shrinkage properties, e.g. acetylated wood, heat treated wood and polymer impregnated wood.
This document is primarily intended for use by adhesive manufacturers and for use in timber products bonded with adhesives, to assess or control the quality of adhesives. This document only specifies the performance of an adhesive for use in an environment corresponding to the defined conditions.
Such an adhesive meeting the requirements of this document for its type is adequate for use in load-bearing timber products, provided that the bonding process has been carried out according to an appropriate product standard.
- Standard20 pagesEnglish languagesale 10% offe-Library read for×1 day
- 14-Feb-2023
- 83.180
- CEN/TC 193
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.