iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 377:2017/prA1

(Amendment)

Steel and steel products - Location and preparation of samples and test pieces for mechanical testing - Amendment 1 (ISO 377:2017/DAM 1:2024)

Steel and steel products - Location and preparation of samples and test pieces for mechanical testing - Amendment 1 (ISO 377:2017/DAM 1:2024)

Stahl und Stahlerzeugnisse - Lage und Vorbereitung von Probenabschnitten und Proben für mechanische Prüfungen - Änderung 1 (ISO 377:2017/DAM 1:2024)

Acier et produits en acier - Position et préparation des échantillons et éprouvettes pour essais mécaniques - Amendement 1 (ISO 377:2017/DAM 1:2024)

Jeklo in jekleni izdelki - Lokacija in priprava vzorcev ter preskušancev za mehansko preskušanje - Dopolnilo A1 (ISO 377:2017/DAM 1:2024)

General Information

Status
Not Published
Publication Date
01-Jun-2026
ICS
77.040.10 - Mechanical testing of metals
Technical Committee
ECISS/TC 100 - General issues
Drafting Committee
ECISS/TC 100 - General issues
Current Stage
4020 - Submission to enquiry - Enquiry
Start Date
07-Nov-2024
Completion Date
07-Nov-2024
Ref Project
SIST EN ISO 377:2017/oprA1:2025 - Steel and steel products - Location and preparation of samples and test pieces for mechanical testing - Amendment 1 (ISO 377:2017/DAM 1:2024)

Relations

Amends
EN ISO 377:2017 - Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377:2017)
Effective Date
01-May-2024

Buy Standard

EN ISO 377:2017/oprA1:2025EN ISO 377:2017/oprA1:2025
PreviousNext
Draft
EN ISO 377:2017/oprA1:2025
English language
5 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-januar-2025
Jeklo in jekleni izdelki - Lokacija in priprava vzorcev ter preskušancev za
mehansko preskušanje - Dopolnilo A1 (ISO 377:2017/DAM 1:2024)
Steel and steel products - Location and preparation of samples and test pieces for
mechanical testing - Amendment 1 (ISO 377:2017/DAM 1:2024)
Stahl und Stahlerzeugnisse - Lage und Vorbereitung von Probenabschnitten und Proben
für mechanische Prüfungen - Änderung 1 (ISO 377:2017/DAM 1:2024)
Acier et produits en acier - Position et préparation des échantillons et éprouvettes pour
essais mécaniques - Amendement 1 (ISO 377:2017/DAM 1:2024)
Ta slovenski standard je istoveten z: EN ISO 377:2017/prA1
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
77.140.01 Železni in jekleni izdelki na Iron and steel products in
splošno general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
Amendment
ISO 377:2017/DAM 1
ISO/TC 17/SC 20
Steel and steel products — Location
Secretariat: SIS
and preparation of samples and test
pieces for mechanical testing
Voting begins on:
2024-11-05
AMENDMENT 1
Voting terminates on:
2025-01-28
Acier et produits en acier — Position et préparation des
échantillons et éprouvettes pour essais mécaniques
AMENDEMENT 1
ICS: 77.040.10
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO 377:2017/DAM 1:2024(en)
DRAFT
ISO 377:2017/DAM 1:2024(en)
Amendment
ISO 377:2017/DAM 1
ISO/TC 17/SC 20
Steel and steel products — Location
Secretariat: SIS
and preparation of samples and test
pieces for mechanical testing
Voting begins on:
AMENDMENT 1
Voting terminates on:
Acier et produits en acier — Position et préparation des
échantillons et éprouvettes pour essais mécaniques
AMENDEMENT 1
ICS: 77.040.10
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2024
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL RE
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 377:2017(Main)
Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377:2017)
SIST EN ISO 377:2017

ISO 377:2017 specifies requirements for the identification, location and preparation of samples and test pieces intended for mechanical tests on steel sections, bars, rod, flat products and tubular products as defined in ISO 6929. If agreed in the order, ISO 377:2017 can also apply to other metallic products. These samples and test pieces are for use in tests that are carried out in conformity with the methods specified in the product or material standard or, in the absence of this, in the standard for the test method.
Where the requirements of the order or product standard differ from those given in ISO 377:2017, then the requirements of the order or product standard apply.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6508-1:2023(Main)
Metallic materials - Rockwell hardness test - Part 1: Test method (ISO 6508-1:2023)
SIST EN ISO 6508-1:2024

This document specifies the method for Rockwell regular and Rockwell superficial hardness tests for scales A, B, C, D, E, F, G, H, K, 15N, 30N, 45N, 15T, 30T, and 45T for metallic materials and is applicable to stationary and portable hardness testing machines.
For specific materials and/or products, other specific International Standards apply (e.g. ISO 3738-1 and ISO 4498).

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6508-2:2023(Main)
Metallic materials - Rockwell hardness test - Part 2: Verification and calibration of testing machines and indenters (ISO 6508-2:2023)
SIST EN ISO 6508-2:2024

This document specifies two separate methods of verification of testing machines (direct and indirect) for determining Rockwell hardness in accordance with ISO 6508-1, together with a method for verifying Rockwell hardness indenters.
The direct verification method is used to determine whether the main parameters associated with the machine function, such as applied force, depth measurement, and testing cycle timing, fall within specified tolerances. The indirect verification method uses a number of calibrated reference hardness blocks to determine how well the machine can measure a material of known hardness.
This document is applicable to stationary and portable hardness testing machines.
Attention is drawn to the fact that the use of tungsten carbide composite for ball indenters is considered to be the standard type of Rockwell indenter ball.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6508-3:2023(Main)
Metallic materials - Rockwell hardness test - Part 3: Calibration of reference blocks (ISO 6508-3:2023)
SIST EN ISO 6508-3:2024

This document specifies a method for the calibration of reference blocks to be used for the indirect and daily verification of Rockwell hardness testing machines and indenters, as specified in ISO 6508-2. This document also specifies requirements for Rockwell machines and indenters used for calibrating reference blocks and specifies methods for their calibration and verification.
Attention is drawn to the fact that the use of hard metal for ball indenters is considered to be the standard type of Rockwell indenter ball.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6507-1:2023(Main)
Metallic materials - Vickers hardness test - Part 1: Test method (ISO 6507-1:2023)
SIST EN ISO 6507-1:2023

This document specifies the Vickers hardness test method for the three different ranges of test force for metallic materials, including hard metals and other cemented carbides (see Table 1), metallic coatings and other inorganic coatings.
The Vickers hardness test is specified in this document for lengths of indentation diagonals between 0,020 mm and 1,400 mm. Using this method to determine Vickers hardness from smaller indentations is outside the scope of this document as results would suffer from large uncertainties due to the limitations of optical measurement and imperfections in tip geometry.
The Vickers hardness specified in this document is also applicable for metallic and other inorganic coatings including electrodeposited coatings, autocatalytic coatings, sprayed coatings and anodic coatings on aluminium.
This document is applicable to measurements normal to the coated surface and to measurements on cross-sections, provided that the characteristics of the coating (smoothness, thickness, etc.) permit accurate readings of the diagonal of the indentation.
This document is not applicable for coatings with thickness less than 0,030 mm when testing normal to the coating surface. This standard is not applicable for coatings with thickness less than 0,100 mm when testing a cross-section of the coating. ISO 14577-1 can be used for the determination of hardness from smaller indentations.”
A periodic verification method is specified for routine checking of the testing machine in service by the user.
For specific materials and/or products, relevant International Standards exist.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 4545-1:2023(Main)
Metallic materials - Knoop hardness test - Part 1: Test method (ISO 4545-1:2023)
SIST EN ISO 4545-1:2023

This document specifies the Knoop hardness test method for metallic materials for test forces from 0,009 807 N to 19,613 N.
This document specifies Knoop hardness tests for length of the long diagonal ≥0,020 mm. Using this method to determine the Knoop hardness from smaller indentations is outside the scope of this document as results would suffer from large uncertainties due to the limitations of optical measurement and imperfections in tip geometry.
The Knoop hardness test specified in this document is also applicable for metallic and other inorganic coatings including electrodeposited coatings, autocatalytic coatings, sprayed coatings and anodic coatings on aluminium. This document is applicable to measurements normal to the coated surface and to measurements on cross-sections, provided that the characteristics of the coating (smoothness, thickness, etc.) permit accurate readings of the diagonal of the indentation. This document is not applicable for coatings with thickness less than 0,007 mm when testing normal to the coating surface. This document is not applicable for coatings with thickness less than 0,020 mm when testing a cross-section of the coating. ISO 14577-1 can be used for the determination of hardness from smaller indentations.
A periodic verification method is specified for routine checking of the testing machine in service by the user.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 5754:2023(Main)
Sintered metal materials, excluding hardmetals - Unnotched impact test piece (ISO 5754:2023)
SIST EN ISO 5754:2023

This document specifies the dimensions of an unnotched impact test piece of sintered metal materials. The test piece may be obtained directly by pressing and sintering or by machining a sintered part.
This document applies to all sintered metals and alloys, with the exception of hardmetals. However, for certain materials (for example, materials with low porosity or materials with high ductility), it may be more appropriate to use a notched test piece which, in this case, will give results with less scatter. (In this case, refer to ISO 148-1.)
NOTE            For porous sintered materials, the results obtained from impact tests on unnotched specimens according to this standard are not fully comparable with results obtained from tests on solid metals tested on notched specimens.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 2740:2023(Main)
Sintered metal materials, excluding hardmetals - Tensile test pieces (ISO 2740:2023)
SIST EN ISO 2740:2023

This document is applicable to all sintered metals and alloys, excluding hardmetals.
This document specifies:
—    the die cavity dimensions used for making tensile test pieces by pressing and sintering, and by metal injection moulding (MIM) and sintering;
—    the dimensions of tensile test pieces machined from sintered and powder forged materials.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 204:2023(Main)
Metallic materials - Uniaxial creep testing in tension - Method of test (ISO 204:2023)
SIST EN ISO 204:2023

This document specifies the methods for:
a)    uninterrupted creep tests with continuous monitoring of extension;
b)    interrupted creep tests with periodic measurement of elongation;
c)    stress rupture tests where normally only the time to fracture is measured;
d)    a test to verify that a predetermined time can be exceeded under a given force, with the elongation or extension not necessarily being reported.
NOTE       A creep test can be continued until fracture has occurred or it can be stopped before fracture.

  • Standard
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 3995:2023(Main)
Metallic powders - Determination of green strength by transverse rupture of rectangular compacts (ISO 3995:2023)
SIST EN ISO 3995:2023

This document specifies a method for the determination of green strength by measuring the transverse rupture strength of compacts of rectangular cross-section.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day