EN ISO 17186:2002

Leather - Physical and mechanical tests - Determination of surface coating thickness (ISO 17186:2002)

ISO 17186:2002 specifies a method for determining the thickness of the surface coating applied to leather when measured under zero compression. It is applicable to all types of leather.

Leder - Physikalische und mechanische Prüfungen - Bestimmung der Dicke der Oberflächendeckschicht (ISO 17186:2002)

Die vorliegende Internationale Norm legt ein Verfahren zur Bestimmung der Dicke der auf das Leder aufgebrachten Deckschicht fest, wobei sie bei der Messung nicht zusammengedrückt wird. Das Verfahren gilt für alle Lederarten.

Cuir - Essais physiques et mécaniques - Détermination de l'épaisseur du revêtement de surface (ISO 17186:2002)

L'ISO 17186:2002 spécifie une méthode pour déterminer l'épaisseur du revêtement de surface appliqué au cuir sous une pression nulle. Elle s'applique à tous les types de cuir.

Usnje - Fizikalni in mehanski preskusi - Ugotavljanje debeline površinskih premazov (ISO 17186:2002)

General Information

• Status: Withdrawn
• Publication Date: 14-Dec-2002
• Withdrawal Date: 14-Dec-2011
• ICS: 59.140.30 - Leather and furs
• Technical Committee: CEN/TC 289 - Leather
• Drafting Committee: CEN/TC 289/WG 2 - Physical test methods
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 15-Dec-2011
• Completion Date: 15-Dec-2011
• Ref Project: SIST EN ISO 17186:2003 - Leather - Physical and mechanical tests - Determination of surface coating thickness (ISO 17186:2002)

Relations

• Replaced By: EN ISO 17186:2011 - Leather - Physical and mechanical tests - Determination of surface coating thickness (ISO 17186:2011)
• Effective Date: 21-Dec-2011

Standards Content (Sample)

SLOVENSKI STANDARD
01-februar-2003
Usnje - Fizikalni in mehanski preskusi - Ugotavljanje debeline površinskih
premazov (ISO 17186:2002)
Leather - Physical and mechanical tests - Determination of surface coating thickness
(ISO 17186:2002)
Leder - Physikalische und mechanische Prüfungen - Bestimmung der Dicke der
Oberflächendeckschicht (ISO 17186:2002)
Cuir - Essais physiques et mécaniques - Détermination de l'épaisseur du revetement de
surface (ISO 17186:2002)
Ta slovenski standard je istoveten z: EN ISO 17186:2002
ICS:
59.140.30 Usnje in krzno Leather and furs
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 17186
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2002
ICS 59.140.30
English version
Leather - Physical and mechanical tests - Determination of
surface coating thickness (ISO 17186:2002)
Cuir - Essais physiques et mécaniques - Détermination de Leder - Physikalische und mechanische Prüfungen -
l'épaisseur du revêtement de surface (ISO 17186:2002) Bestimmung der Dicke der Oberflächendeckschicht (ISO
17186:2002)
This European Standard was approved by CEN on 8 June 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17186:2002 E
worldwide for CEN national Members.

CORRECTED  2003-08-27
Foreword
This document (EN ISO 17186:2002) has been prepared by Technical Committee CEN/TC 289
"Leather", the secretariat of which is held by UNI, in collaboration with the International Union of
Leather Technologists and Chemists Societies (IULTCS).
It is based on Method IUP 41 of the International Union of Leather Technologists and Chemists
Societies.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by June 2003, and conflicting national
standards shall be withdrawn at the latest by June 2003.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,
Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 17186:2002 has been approved by CEN as EN ISO 17186:2002 without any
modifications.
NOTE Normative references to International Standards are listed in Annex ZA (normative).
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 2418 2002 Leather - Chemical, physical EN ISO 2418 2002
and mechanical and fastness
tests - Sampling location
ISO 2419 2002 Leather - Physical and EN ISO 2419 2002
mechanical tests - Sample
preparation and conditioning
INTERNATIONAL ISO
STANDARD 17186
IULTCS/IUP
First edition
2002-12-15
Leather — Physical and mechanical
tests — Determination of surface coating
thickness
Cuir — Essais physiques et mécaniques — Détermination de l’épaisseur
du revêtement de surface
Reference number
ISO 17186:2002(E)
IULTCS/IUP 41
©
ISO 2002
ISO 17186:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2002 – All rights reserved

ISO 17186:2002(E)
Contents
Page
Foreword.iv
1 Scope .1
2 Normative references .1
3 Principle.1
4 Apparatus .1
5 Sampling and sample preparation .1
6 Procedure .2
7 Expression of results .4
8 Test report .4
ISO 17186:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as
...