EN 28430-2:1992
(Main)Resistance spot welding - Electrode holders - Part 2: Morse taper fixing (ISO 8430-2:1988)
Resistance spot welding - Electrode holders - Part 2: Morse taper fixing (ISO 8430-2:1988)
Specifies the dimensions and tolerances of resistance spot welding electrode holders (type B) without offset and with a facility for cable clamping, and where a male Morse taper is used to fix the holder directly to the welding cylinder in multiple spot welding equipment. Covers also designation, materials, delivery conditions and marking.
Widerstandspunktschweißen - Elektrodenhalter - Teil 2: Morsekegelbefestigung (ISO 8430-2:1988)
Soudage par points par résistance - Porte-électrodes - Partie 2: Cône Morse de fixation (ISO 8430-2:1988)
La présente partie de l'ISO 8430 prescrit les dimensions et tolérances des porte-électrodes non excentrés pour soudage par points par résistance prévus pour la fixation de câble et qui présentent un cône Morse mâle (type B) permettant d'emmancher directement le porte-électrode sur le vérin, dans les équipements pour soudage multipoint.
Elektrouporovno varjenje – Držala elektrod – 2. del: Konična pritrditev, Morsejev konus (ISO 8430-2:1988)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Widerstandspunktschweißen - Elektrodenhalter - Teil 2: Morsekegelbefestigung (ISO 8430-2:1988)Soudage par points par résistance - Porte-électrodes - Partie 2: Cône Morse de fixation (ISO 8430-2:1988)Resistance spot welding - Electrode holders - Part 2: Morse taper fixing (ISO 8430-2:1988)25.160.30Varilna opremaWelding equipmentICS:Ta slovenski standard je istoveten z:EN 28430-2:1992SIST EN 28430-2:1999en01-december-1999SIST EN 28430-2:1999SLOVENSKI
STANDARD
SIST EN 28430-2:1999
SIST EN 28430-2:1999
SIST EN 28430-2:1999
INTERNATIONAL STANDARD INTERNATIONAL ORGANIZATION FOR STANDARDIZATION ORGANISATION INTERNATIONALE DE NORMALISATION MEXAYHAPOflHAR OPrAHM3Al#lR I-IO CTAHflAPTM3A~MM Resistance spot welding - Electrode holders - Part 2 : Morse taper fixing Soudage par Points par rbsistance - Porte-blectrodes - Partie 2: C6ne Morse de fixation ISO 8430-2 First edition 1988-12-01 Reference number ISO 8430-2 : 1988 (E) SIST EN 28430-2:1999
ISO 8430-2:1988 (EI Foreword ISO (the International Organization for Standardization) is a worldwide federation of national Standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Esch member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, govern- mental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for approval before their acceptance as International Standards by the ISO Council. They are approved in accordance with ISO procedures requiring at least 75 % approval by the member bodies voting. International Standard ISO 84302 was prepared by Technical Committee ISO/TC 44, Welding and allied processes. ISO 8430 consists of the following Parts, under the general title Resistance spot welding - Electrode holders : - Part 7: Taper fixing 7 : 70 - Part 2: Morse taper fixing - Part 3: Parallel shank fixing for end thrust 0 International Organkation for Standardkation, 1988 Printed in Switzerland SIST EN 28430-2:1999
INTERNATIONAL STANDARD ISO 8430-2 : 1988 (E) Resistance spot welding - Electrode holders - Part 2 : Morse taper fixing 1 Scope This part of ISO 8430 specifies the dimensions and tolerantes of resistance spot welding electrode holders (type 9) without offset and with a facility for cable clamping, and where a male Morse taper is used to fix the holder directly to the welding cylinder in multiple spot welding equipment. 2 Normative references The following Standards contain provisions which, through reference in this text, constitute provisions of this part of ISO 8430. At the time of publication, the editions indicated were valid. All Standards are subject to revision, and Parties to agreements based on this part of ISO 8430 are encouraged to in- vestigate the possibility of applying the most recent editions of the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.