EN ISO 283:2007

Textile conveyor belts - Full thickness tensile strength, elongation at break and elongation at the reference load - Test method (ISO 283:2007)

ISO 283:2007 specifies a test method for the determination of the full thickness tensile strength in the longitudinal direction and the elongation at the reference force and breaking point of conveyor belts having a textile carcass. The method can also be used for the determination of full thickness tensile strength in the transverse direction and the elongation at the breaking point, for use when the manufacturer is requested by the purchaser to state values for these properties. It is not suitable or valid for light conveyor belts as described in ISO 21183-1.

Textilfördergurte - Zugfestigkeit bei voller Gurtdicke, Bruchdehnung und Dehnung bei breitenbezogener Bruchkraft - Prüfverfahren (ISO 283:2007)

Diese Internationale Norm legt ein Prüfverfahren zur Bestimmung der breitenbezogenen Bruchkraft und der Dehnung in Längsrichtung von Textilfördergurten bei voller Gurtdicke fest. Außerdem legt sie das Verfahren zur Bestimmung der breitenbezogenen Bruchkraft in Querrichtung und die Bruchdehnung in Längsrichtung fest, für den Fall, dass der Käufer den Hersteller auffordert, Werte für den Gebrauch vorzulegen.
Diese Internationale Norm ist nicht gültig oder anwendbar auf die in ISO 21183-1 beschriebenen leichten Fördergurte.

Courroies transporteuses à carcasse textile - Résistance à la traction, allongement à la rupture et allongement sous force de référence en pleine épaisseur - Méthode d'essai (ISO 283:2007)

L'ISO 283:2007 spécifie une méthode d'essai pour déterminer la résistance à la traction dans le sens longitudinal et l'allongement sous force de référence et le point de rupture des courroies transporteuses à carcasse textile. La méthode peut également être utilisée pour la détermination de la résistance à la traction dans le sens transversal et de l'allongement au point rupture, utilisables lorsque l'acheteur demande au fabricant de déclarer les valeurs de ces propriétés.
L'ISO 283:2007 n'est pas applicable ou valable pour les courroies transporteuses légères décrites dans l'ISO 21183-1.

Naprave za kontinuirni transport - Trakovi tračnih transporterjev - Natezna trdnost pri polni debelini traku, raztezek pri porušitvi in raztezek pri referenčni sili - Metoda preskušanja (ISO 283:2007)

General Information

• Status: Withdrawn
• Publication Date: 14-Jun-2007
• Withdrawal Date: 17-Nov-2015
• ICS: 53.040.20 - Components for conveyors
• Technical Committee: CEN/TC 188 - Conveyor belts
• Drafting Committee: CEN/TC 188/WG 1 - Technical test methods
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 18-Nov-2015
• Directive: 98/37/EC - Machinery
• Mandate: M/BC/CEN/88/13 - Standardization request to CEN/CENELEC relating to machinery
• Ref Project: SIST EN ISO 283:2008 - Textile conveyor belts - Full thickness tensile strength, elongation at break and elongation at the reference load - Test method (ISO 283:2007)

Relations

• Replaces: EN ISO 283-1:2000 - Textile conveyor belts - Full thickness tensile testing - Part 1: Determination of tensile strength, elongation at break and elongation at the reference load (ISO 283-1:2000)
• Effective Date: 22-Dec-2008
• Replaced By: EN ISO 283:2015 - Textile conveyor belts - Full thickness tensile strength, elongation at break and elongation at the reference load - Test method (ISO 283:2015)
• Effective Date: 25-Nov-2015

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 283:2008
01-maj-2008
1DSUDYH]DNRQWLQXLUQLWUDQVSRUW7UDNRYLWUDþQLKWUDQVSRUWHUMHY1DWH]QDWUGQRVW
SULSROQLGHEHOLQLWUDNXUD]WH]HNSULSRUXãLWYLLQUD]WH]HNSULUHIHUHQþQLVLOL0HWRGD
SUHVNXãDQMD,62
Textile conveyor belts - Full thickness tensile strength, elongation at break and
elongation at the reference load - Test method (ISO 283:2007)
Textilfördergurte - Zugfestigkeit bei voller Gurtdicke, Bruchdehnung und Dehnung bei
Bezugskraft - Prüfverfahren (ISO 283:2007)
Courroies transporteuses a carcasse textile - Résistance a la traction, allongement a la
rupture et allongement sous force de référence en pleine épaisseur - Méthode d'essai
(ISO 283:2007)
Ta slovenski standard je istoveten z: EN ISO 283:2007
ICS:
53.040.20
SIST EN ISO 283:2008 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN ISO 283
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2007
ICS 53.040.20 Supersedes EN ISO 283-1:2000
English Version
Textile conveyor belts - Full thickness tensile strength,
elongation at break and elongation at the reference load - Test
method (ISO 283:2007)
Courroies transporteuses à carcasse textile - Résistance à Textilfördergurte - Zugfestigkeit bei voller Gurtdicke,
la traction, allongement à la rupture et allongement sous Bruchdehnung und Dehnung bei breitenbezogener
force de référence en pleine épaisseur - Méthode d'essai Bruchkraft - Prüfverfahren (ISO 283:2007)
(ISO 283:2007)
This European Standard was approved by CEN on 23 May 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 283:2007: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN ISO 283:2007 (E)





Foreword


This document (EN ISO 283:2007) has been prepared by Technical Committee ISO/TC 41
"Pulleys and belts (including veebelts)" in collaboration with Technical Committee CEN/TC 188
"Conveyor belts", the secretariat of which is held by BSI.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by December 2007, and conflicting national
standards shall be withdrawn at the latest by December 2007.

This document supersedes EN ISO 283-1:2000.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United
Kingdom.


Endorsement notice

The text of ISO 283:2007 has been approved by CEN as EN ISO 283:2007 without any
modifications.

2

---------------------- Page: 3 ----------------------

INTERNATIONAL ISO
STANDARD 283
Third edition
2007-06-15


Textile conveyor belts — Full thickness
tensile strength, elongation at break and
elongation at the reference load — Test
method
Courroies transporteuses à carcasse textile — Résistance à la traction,
allongement à la rupture et allongement sous force de référence en
pleine épaisseur — Méthode d'essai




Reference number
ISO 283:2007(E)
©
ISO 2007

---------------------- Page: 4 ----------------------

ISO 283:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the compute
...