EN ISO 283:2015
(Main)Textile conveyor belts - Full thickness tensile strength, elongation at break and elongation at the reference load - Test method (ISO 283:2015)
Textile conveyor belts - Full thickness tensile strength, elongation at break and elongation at the reference load - Test method (ISO 283:2015)
ISO 283:2015 specifies a test method for the determination of the full thickness tensile strength in the longitudinal direction and the elongation at the reference force and breaking point of conveyor belts having a textile carcass. The method can also be used for the determination of full thickness tensile strength in the transverse direction and the elongation at the breaking point, for use when the manufacturer is requested by the purchaser to state values for these properties.
ISO 283:2015 is not suitable or valid for light conveyor belts as described in ISO 21183‑1.
Textilfördergurte - Zugfestigkeit bei voller Gurtdicke, Bruchdehnung und Dehnung bei breitenbezogener Bruchkraft - Prüfverfahren (ISO 283:2015)
Diese Internationale Norm legt ein Prüfverfahren zur Bestimmung der breitenbezogenen Bruchkraft und der Dehnung in Längsrichtung von Textilfördergurten bei voller Gurtdicke fest. Außerdem legt sie das Verfahren zur Bestimmung der breitenbezogenen Bruchkraft in Querrichtung und die Bruchdehnung in Längsrichtung fest, für den Fall, dass der Käufer den Hersteller auffordert, Werte für den Gebrauch vorzulegen.
Diese Internationale Norm ist nicht gültig oder anwendbar auf die in ISO 21183-1 beschriebenen leichten Fördergurte.
Courroies transporteuses à carcasse textile - Résistance à la traction, allongement à la rupture et allongement sous force de référence en pleine épaisseur - Méthode d'essai (ISO 283:2015)
ISO 283:2015 spécifie une méthode d'essai pour déterminer la résistance à la traction dans le sens longitudinal, l'allongement sous force de référence et le point de rupture des courroies transporteuses à carcasse textile en pleine épaisseur. La méthode peut également être utilisée pour la détermination de la résistance à la traction dans le sens transversal et de l'allongement au point de rupture en pleine épaisseur, utilisables lorsque l'acheteur demande au fabricant de déclarer les valeurs de ces propriétés.
ISO 283:2015 n'est pas applicable ou valable pour les courroies transporteuses légères décrites dans l'ISO 21183‑1.
Naprave za kontinuirni transport - Trakovi tračnih transporterjev - Natezna trdnost pri polni debelini traku, raztezek pri porušitvi in raztezek pri referenčni sili - Preskusna metoda (ISO 283:2015)
Ta mednarodni standard določa metodo preskušanja za določanje natezne trdnosti pri polni debelini po vzdolžni osi in raztezka pri referenčni sili ter točke preloma trakov tračnih transporterjev s trupom iz tekstila. To metodo je mogoče uporabiti tudi za določanje natezne moči pri polni debelini v transverzalni smeri ter raztezka pri točki preloma, za uporabo v primerih, kjer kupec od proizvajalca zahteva navedbe vrednosti za te lastnosti. Ta mednarodni standard se ne uporablja oziroma ni veljaven za lahke trakove tračnih transporterjev iz standarda ISO 21183-1.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 283:2016
01-februar-2016
1DGRPHãþD
SIST EN ISO 283:2008
1DSUDYH]DNRQWLQXLUQLWUDQVSRUW7UDNRYLWUDþQLKWUDQVSRUWHUMHY1DWH]QDWUGQRVW
SULSROQLGHEHOLQLWUDNXUD]WH]HNSULSRUXãLWYLLQUD]WH]HNSULUHIHUHQþQLVLOL
3UHVNXVQDPHWRGD ,62
Textile conveyor belts - Full thickness tensile strength, elongation at break and
elongation at the reference load - Test method (ISO 283:2015)
Textilfördergurte - Zugfestigkeit bei voller Gurtdicke, Bruchdehnung und Dehnung bei
breitenbezogener Bruchkraft - Prüfverfahren (ISO 283:2015)
Courroies transporteuses à carcasse textile - Résistance à la traction, allongement à la
rupture et allongement sous force de référence en pleine épaisseur - Méthode d'essai
(ISO 283:2015)
Ta slovenski standard je istoveten z: EN ISO 283:2015
ICS:
53.040.20 Deli za transporterje Components for conveyors
SIST EN ISO 283:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 283:2016
---------------------- Page: 2 ----------------------
SIST EN ISO 283:2016
EN ISO 283
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2015
EUROPÄISCHE NORM
ICS 53.040.20 Supersedes EN ISO 283:2007
English Version
Textile conveyor belts - Full thickness tensile strength,
elongation at break and elongation at the reference load -
Test method (ISO 283:2015)
Courroies transporteuses à carcasse textile - Textilfördergurte - Zugfestigkeit bei voller Gurtdicke,
Résistance à la traction, allongement à la rupture et Bruchdehnung und Dehnung bei breitenbezogener
allongement sous force de référence en pleine Bruchkraft - Prüfverfahren (ISO 283:2015)
épaisseur - Méthode d'essai (ISO 283:2015)
This European Standard was approved by CEN on 24 October 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 283:2015 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 283:2016
EN ISO 283:2015 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 283:2016
EN ISO 283:2015 (E)
European foreword
This document (EN ISO 283:2015) has been prepared by Technical Committee ISO/TC 41 “Pulleys and
belts (including veebelts)” in collaboration with Technical Committee CEN/TC 188 “Conveyor belts” the
secretariat of which is held by SNV.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2016, and conflicting national standards shall be
withdrawn at the latest by May 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 283:2007.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.