EN 14609:2004

Windows - Determination of the resistance to static torsion

This European Standard specifies the determination of permanent deformation caused by a static load applied to an open casement.
This European Standard applies to the opening modes specified in Figure A.1 to Figure A.5 and included in prEN 12519.
This test is not applicable to the sashes of sliding windows.

Fenster - Ermittlung der Widerstandsfähigkeit gegen statische Verwindung

Fenêtres - Détermination de la résistance à la torsion statique

Okna – Ugotavljanje odpornosti proti statični torzijski obremenitvi

General Information

• Status: Published
• Publication Date: 08-Jun-2004
• Withdrawal Date: 30-Mar-2005
• ICS: 91.060.50 - Doors and windows
• Technical Committee: CEN/TC 33 - Doors, windows, shutters and building hardware
• Drafting Committee: CEN/TC 33/WG 1/2 - Windows and doors
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 10-Jan-2023
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Ref Project: SIST EN 14609:2004 - Windows - Determination of the resistance to static torsion

Standards Content (Sample)

SLOVENSKI STANDARD
01-september-2004
2NQD±8JRWDYOMDQMHRGSRUQRVWLSURWLVWDWLþQLWRU]LMVNLREUHPHQLWYL
Windows - Determination of the resistance to static torsion
Fenster - Ermittlung der Widerstandsfähigkeit gegen statische Verwindung
Fenetres - Détermination de la résistance a la torsion statique
Ta slovenski standard je istoveten z: EN 14609:2004
ICS:
91.060.50 Vrata in okna Doors and windows
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 14609
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2004
ICS 91.060.50
English version
Windows - Determination of the resistance to static torsion
Fenêtres - Détermination de la résistance à la torsion Fenster - Ermittlung der Widerstandsfähigkeit gegen
statique statische Verwindung
This European Standard was approved by CEN on 1 September 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14609:2004: E
worldwide for CEN national Members.

Contents
1 Scope.4
2 Normative references.4
3 Terms and definitions .4
4 Apparatus.4
5 Test specimen.4
6 Conditioning and preparation of the test specimen .5
6.1 Conditioning.5
6.2 Preparation.5
7 Procedure.5
8 Expression of results.5
9 Test report.5
Annex A (normative) Figures .6

Foreword
This document (EN 14609:2004) has been prepared by Technical Committee CEN/TC 33 “Doors, windows,
shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by December 2004, and conflicting national standards shall be withdrawn at the latest
by December 2004.
It is part of a series of standards for windows.
This document supersedes 8.2.1 Warping of EN 107:1980.
Annex A is normative.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
1 Scope
This European Standard specifies the determinat
...