FprEN 13322-1

Transportable gas cylinders - Refillable welded steel gas cylinders - Design and construction - Part 1: Carbon steel

This document specifies minimum requirements concerning material, design, construction and workmanship, manufacturing processes and testing of refillable transportable welded carbon steel gas cylinders of water capacities up to and including 150 l for compressed, liquefied and dissolved gases.
For acetylene service, additional requirements for the cylinder and basic requirements for the porous material are given in EN ISO 3807. For cylinder shells for acetylene service manufactured from high frequency induction (HFI) welded steel tubes by spinning of the end, the requirements are given in Annex A.
This document is primarily applicable to industrial gases other than LPG but can also be applied for LPG. However for dedicated LPG cylinders, see EN 1442.

Ortsbewegliche Gasflaschen - Wiederbefüllbare geschweiβte Flaschen aus Stahl - Auslegung und Herstellung - Teil 1: Flaschen aus Kohlenstoffstahl

Dieses Dokument legt Mindestanforderungen bezüglich Werkstoff, Auslegung, Herstellung und Ausführung, Herstellungsprozessen und Prüfung von wiederbefüllbaren geschweißten ortsbeweglichen Gasflaschen aus Kohlenstoffstahl mit einem Fassungsraum bis einschließlich 150 l für verdichtete, verflüssigte und unter Druck gelöste Gase fest.
Die Anforderungen für Flaschen aus hochfrequenzinduktiv (HFI) geschweißten Stahlrohren mit gedrehtem Ende sind in Anhang A angegeben. Dieses Dokument gilt in erster Linie für andere Industriegase als Flüssiggas (LPG, en: liquefied petroleum gas), kann aber auch für Flüssiggas angewendet werden. Für besondere Flaschen für Flüssiggas (LPG) siehe jedoch EN 1442 "Ortsbewegliche, wiederbefüllbare, geschweißte Flaschen aus Stahl für Flüssiggas (LPG) - Auslegung und Bau", die vom CEN/TC 286 "Flüssiggas-Geräte und Ausrüstungsteile" erarbeitet wurde.

Bouteilles à gaz transportables - Bouteilles à gaz rechargeables soudées en acier - Conception et construction - Partie 1 : Acier au carbone

Le présent document spécifie les exigences minimales concernant les matériaux, la conception, la construction et l’exécution, ainsi que les procédés de fabrication et les essais des bouteilles à gaz transportables et rechargeables en acier au carbone soudées ayant une capacité en eau allant jusqu’à 150 l inclus, destinées à transporter des gaz comprimés, liquéfiés et dissous.
Des exigences complémentaires s’appliquant aux bouteilles destinées à contenir de l’acétylène et des exigences fondamentales s’appliquant à la masse poreuse sont données dans l’EN ISO 3807. Pour les viroles de bouteilles destinées à contenir de l’acétylène fabriquées à partir de tubes en acier soudés par induction à haute fréquence (IHF) par emboutissage de l’extrémité, les exigences sont données dans l’Annexe A.
Ce document concerne principalement les gaz industriels autres que le GPL, mais peut aussi être appliqué au GPL. Cependant, pour les bouteilles à gaz dédiées au GPL, voir l’EN 1442.

Premične plinske jeklenke - Ponovno polnljive varjene jeklenke iz jekla - Konstruiranje in izdelava - 1. del: Jeklenke iz ogljičnega jekla

General Information

• Status: Not Published
• Publication Date: 29-May-2024
• ICS: 23.020.35 - Gas cylinders
• Technical Committee: CEN/TC 23 - Transportable gas cylinders
• Drafting Committee: CEN/TC 23/SC 1/WG 2 - Welded/brazed cylinders excluding cylinders for LPG
• Current Stage: 5020 - Submission to Vote - Formal Approval
• Start Date: 08-Feb-2024
• Due Date: 10-Nov-2022
• Completion Date: 08-Feb-2024
• Ref Project: kSIST FprEN 13322-1:2024 - Transportable gas cylinders - Refillable welded steel gas cylinders - Design and construction - Part 1: Carbon steel

Relations

• Revises: EN 13322-1:2003 - Transportable gas cylinders - Refillable welded steel gas cylinders - Design and construction - Part 1: Carbon steel
• Effective Date: 19-Jan-2023
• Revises: EN 13322-1:2003/A1:2006 - Transportable gas cylinders - Refillable welded steel gas cylinders - Design and construction - Part 1: Carbon steel
• Effective Date: 18-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 13322-1:2021
01-september-2021
Premične plinske jeklenke - Ponovno polnljive varjene jeklenke iz jekla -
Konstruiranje in izdelava - 1. del: Jeklenke iz ogljičnega jekla
Transportable gas cylinders - Refillable welded steel gas cylinders - Design and
construction - Part 1: Carbon steel
Ortsbewegliche Gasflaschen - Wiederbefüllbare geschweißte Flaschen aus Stahl -
Auslegung und Herstellung - Teil 1: Flaschen aus Kohlenstoffstahl
Bouteilles a gaz transportables - Bouteilles a gaz rechargeables soudées en acier -
Conception et construction - Partie 1: Acier au carbone
Ta slovenski standard je istoveten z: prEN 13322-1
ICS:
23.020.35 Plinske jeklenke Gas cylinders
oSIST prEN 13322-1:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 13322-1:2021

---------------------- Page: 2 ----------------------
oSIST prEN 13322-1:2021


DRAFT
EUROPEAN STANDARD
prEN 13322-1
NORME EUROPÉENNE

EUROPÄISCHE NORM

September 2021
ICS 23.020.35 Will supersede EN 13322-1:2003
English Version

Transportable gas cylinders - Refillable welded steel gas
cylinders - Design and construction - Part 1: Carbon steel
 Ortsbewegliche Gasflaschen - Wiederbefüllbare
geschweißte Flaschen aus Stahl - Auslegung und
Herstellung - Teil 1: Flaschen aus Kohlenstoffstahl
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 23.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13322-1:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 13322-1:2021
prEN 13322-1:2021 (E)
Contents Page
European foreword . 4
Introduction . 5
1 Scope. 6
2 Normative references . 6
3 Terms and definitions . 7
3.1 Terms and definitions . 7
3.2 Symbols . 8
4 Materials and heat treatment . 9
4.1 General . 9
4.2 Heat treatment . 9
5 Design .
...