EN 755-2:2024

Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 2: Mechanical properties

This document specifies the mechanical property limits resulting from tensile testing applicable to aluminium and aluminium alloy extruded rod/bar, tube and profile.
Technical conditions for inspection and delivery, including product and testing requirements, are specified in EN 755-1. Temper designations are defined in EN 515. The chemical composition limits for these materials are given in EN 573-3.

Aluminium und Aluminiumlegierungen - Stranggepresste Stangen, Rohre und Profile - Teil 2: Mechanische Eigenschaften

Dieses Dokument legt die Grenzwerte für die mechanischen Eigenschaften von stranggepressten Stangen, Rohren und Profilen aus Aluminium und Aluminiumlegierungen fest.
Die Technischen Lieferbedingungen, einschließlich Erzeugnis- und Prüfanforderungen, sind in EN 755 1 festgelegt. Die Bezeichnungen der Werkstoffzustände sind in EN 515 definiert. In EN 573 3 sind die Grenzen der chemischen Zusammensetzung für diese Werkstoffe angegeben.

Aluminium et alliages d'aluminium - Barres, tubes et profilés filés - Partie 2 : Caractéristiques mécaniques

Le présent document spécifie les limites des caractéristiques mécaniques provenant de l’essai de traction applicables aux barres, tubes et profilés filés en aluminium et alliages d’aluminium.
Les conditions techniques de contrôle et de livraison, y compris les exigences relatives aux produits et aux essais, sont spécifiées dans l’EN 755-1. La désignation des états métallurgiques est définie dans l’EN 515. Les limites de composition chimique de ces matériaux sont données dans l’EN 573-3.

Aluminij in aluminijeve zlitine - Iztiskane palice/drogovi, cevi in profili - 2. del: Mehanske lastnosti

General Information

• Status: Not Published
• Publication Date: 22-Sep-2024
• ICS: 77.150.10 - Aluminium products
• Technical Committee: CEN/TC 132 - Aluminium and aluminium alloys
• Drafting Committee: CEN/TC 132/WG 5 - Extruded and drawn products
• Current Stage: 6055 - CEN Ratification completed (DOR) - Publishing
• Start Date: 26-Aug-2024
• Due Date: 17-Jan-2025
• Completion Date: 26-Aug-2024
• Ref Project: kSIST FprEN 755-2:2024 - Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 2: Mechanical properties

Relations

• Revises: EN 755-2:2016 - Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 2: Mechanical properties
• Effective Date: 28-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 755-2:2023
01-julij-2023
Aluminij in aluminijeve zlitine - Iztiskane palice/drogovi, cevi in profili - 2. del:
Mehanske lastnosti
Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 2:
Mechanical properties
Aluminium und Aluminiumlegierungen - Stranggepresste Stangen, Rohre und Profile -
Teil 2: Mechanische Eigenschaften
Aluminium et alliages d'aluminium - Barres, tubes et profilés filés - Partie 2 :
Caractéristiques mécaniques
Ta slovenski standard je istoveten z: prEN 755-2
ICS:
77.150.10 Aluminijski izdelki Aluminium products
oSIST prEN 755-2:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

oSIST prEN 755-2:2023
oSIST prEN 755-2:2023
DRAFT
EUROPEAN STANDARD
prEN 755-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2023
ICS 77.150.10 Will supersede EN 755-2:2016
English Version
Aluminium and aluminium alloys - Extruded rod/bar, tube
and profiles - Part 2: Mechanical properties
Aluminium et alliages d'aluminium - Barres, tubes et Aluminium und Aluminiumlegierungen -
profilés filés - Partie 2 : Caractéristiques mécaniques Stranggepresste Stangen, Rohre und Profile - Teil 2:
Mechanische Eigenschaften
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 132.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 755-2:2023 E
worldwide for CEN national Members.

oSIST prEN 755-2:2023
EN 755-2:2023 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Mechanical property limits . 4
4.1 General . 4
4.2 Elongation . 4
4.3 Tables of mechanical properties . 5
Annex A (informative) List of tempers used in Tables 1 to 64 (extract of EN 515) . 67
Bibliography . 69

oSIST prEN 755-2:2023
EN 755-2:2023 (E)
European foreword
This document (prEN 755-2:2023) has been prepared by Technical Committee CEN/TC 132 “Aluminium
and aluminium alloys”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 755-2:2016.
Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 5
“Extruded and drawn products” to revise EN 755-2:2016.
The main changes compared to the previous edition are listed below:
— addition of the alloy EN AW-2033 in Table 11;
— addition of the alloy EN AW-2077 in Table 12;
— addition of the alloy EN AW-6050 in Table 39;
— modification of the order of alloys to conform with Aluminium Association System:
— addition of the terms required by the latest CCMC template;
— addition of Clause 3 compulsory from the latest CCMC template;
— deletion of former Clause 3.3 as part of the table of contents in this document;
— correction to temper of EN AW-2024 alloy in Table 10.
The EN 755 series comprises the following parts under the general title “Aluminium and aluminium
alloys — Extruded rod/bar, tube and profiles”:
— Part 1: Technical conditions for inspection and delivery
— Part 2: Mechanical properties
— Part 3: Round bars, tolerances on dimensions and form
— Part 4: Square bars, tolerances on dimensions and form
— Part 5: Rectangular bars, tolerances on dimensions and form
— Part 6: Hexagonal bars, tolerances on dimensions and form
— Part 7: Seamless tubes, tolerances on dimensions and form
— Part 8: Porthole tubes, tolerances on dimensions and form
— Part 9: Profiles, tolerances on dimensions and form
oSIST prEN 755-2:2023
EN 755-2:2023 (E)
1 Scope
This document specifies the mechanical property limits resulting from tensile testing applicable to
aluminium and aluminium alloy extruded rod/bar, tube and profile.
Technical conditions for inspection and delivery, including product and testing requirements, are
specified in EN 755-1. Temper designations are defined in EN 515. The chemical composition limits for
these materials are given in EN 573-3.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 755-1, Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 1: Technical
conditions for inspection and delivery
EN ISO 6892-1, Metallic materials - Tensile testing - Part 1: Method of test at room temperature
(ISO 6892-1)
3 Terms and definitions
No terms and definitions are listed in this document.
4 Mechanical property limits
4.1 General
The mechanical properties shall be in conformity with those specified in Table 1 to Table 64 or those
agreed upon between supplier and purchaser and stated in the order document.
Table 1 to Table 64 contain limits of mechanical property values obtained by tensile testing according to
EN ISO 6892-1 after sampling and test piece preparation according to EN 755-1.
NOTE The mechanical properties refer to test pieces taken in the longitudinal direction. Mechanical properties
of test pieces taken in other directions can differ from those for the longitudinal direction quoted in this document.
Brinell hardness values given in Table 1 to Table 64 expressed as HBW values are for information only.
4.2 Elongation
If not otherwise agreed, the A value shall be used.
The A value for elongation is the % elongation measured over a gauge length of 5,65 S (where S is the
o
o
initial cross-sectional area of the test-piece), and expressed in percent.
For certain products the supplier may choose (if not otherwise specified in the order documents) to use
the elongation based on A Consequently, values for the A are included in the following tables.
50mm. 50mm
The A value is the elongation measured over a gauge length of 50 mm and expressed in percent.
50mm
Test pieces and their location in the specimen are given in EN 755-1.
oSIST prEN 755-2:2023
EN 755-2:2023 (E)
4.3 Tables of mechanical properties
Table 1 — Aluminium EN AW-1050A [Al 99,5]
Extruded rod/bar
Dimensions R R A A
m p0,2 50 mm
Hardness
Temper mm MPa MPa % %
Typical value
a b HBW
D S min. max. min. max. min. min.
c
F , H112 all all 60 - 20 - 25 23 20
O, H111 all all 60 95 20 - 25 23 20
Extruded tube
R R
Wall thickness m p0,2 A A
50 mm
Hardness
Temper t MPa MPa
% %
Typical value
HBW
mm min. min
min. max. min. max.
c
F , H112 all 60  20 - 25 23 20
O, H111 all 60 95 20 - 25 23 20
Extruded profile
Wall thickness R R A A
m p0,2 50 mm
Hardness
Temper t MPa MPa % %
Typical value
HBW
mm min. max. min. max. min. min
c
F , H112 all 60  20 - 25 23 20
a
D = Diameter for round bar.
b
S = Width across flats for square and hexagonal bar, thickness for rectangular bar.
c
F Temper: property values are for information only.
Table 2 — Aluminium EN AW-1070A [Al 99,7]
Extruded rod/bar
Dimensions R R A A
m p0,2 50 mm
Hardness
Temper mm MPa MPa % %
Typical value
a b HBW
D S min. max. min. max. min. min.
c
F , H112 all all 60 - 23  25 23 18
Extruded tube
Not specified
Extruded profile
Not specified
a
D = Diameter for round bar.
b
S = Width across flats for square and hexagonal bar, thickness for rectangular bar.
c
F Temper: property values are for information only.
oSIST prEN 755-2:2023
EN 755-2:2023 (E)
Table 3 — Aluminium EN AW-1200 [Al 99,0]
Extruded rod/bar
Dimensions R
Rm p0,2 A A
50 mm
Hardness
mm MPa MPa
Temper % %
Typical value
HBW
a b
min. max. min. max. min. min.
D S
c
F , H112 all all 75 - 25 - 20 18 23
Extruded tube
Wall thickness
R R A A
m p0,2 50 mm
Hardness
Temper t MPa MPa % %
Typical value
HBW
mm min. max. min. max. min. min.
c
F , H112 all all 75 - 25  20 18 23
Extruded profile
Wall thickness
R R A A
m p0,2 50 mm
Hardness
Temper t MPa MPa % %
Typical value
HBW
mm min. max. min. max. min. min.
c
F , H112 all 75 - 25  20 18 23
a
D = Diameter for round bar.
b
S = Width across flats for square and hexagonal bar, thickness for rectangular bar.
c
F Temper: property values are for information only.
oSIST prEN 755-2:2023
EN 755-2:2023 (E)
Table 4 — Aluminium EN AW-1350 [Al 99,5]
d
Extruded rod/bar
Dimensions Rm Rp0,2 Hardness
A A50 mm
mm MPa MPa Typical
Temper % %
value
a b
D S min. max. min. max. min. min.
HBW
c
F , H112 all all 60 - - - 25 23 20
d
Extruded tube
R R Hardness
m p0,2
Wall thickness A A
50 mm
MPa MPa Typical
Temper t % %
value
mm min. max. min. max. min. min.
HBW
c
F , H112 all 60 - - - 25 23 20
d
Extruded profile
R R Hardness
m p0,2
Wall thickness A A
50 mm
MPa MPa Typical
Temper t % %
value
mm min. max. min. max. min. min.
HBW
c
F , H112 all 60 - - - 25 23 20
a
D = Diameter for round bar.
b
S = Width across flats for square and hexagonal bar, thickness for rectangular bar.
c
F Temper: property values are for information only.
d
Electrical conductivity γ ≥ 35,4 MS/m.
oSIST prEN 755-2:2023
EN 755-2:2023 (E)
Table 5 — Alloy EN AW-2007 [Al Cu4PbMgMn]
Extruded rod/bar
Dimensions R Hardness
Rm p0,2
A A
50 mm
Typical
mm MPa MPa
Temper
% %
value
a b
D S min. max. min. max. min. min.
HBW
≤ 80 ≤ 80 370 - 250 - 8 6
T4, T4510,
80 < D ≤ 200 80 < S ≤ 200 340 - 220 - 8 - 95
c
T4511
200 < D ≤ 250 200 < S ≤ 250 330 - 210 - 7 -
Extruded tube
Hardness
R R
m p0,2
Wall thickness
A A
50 mm
Typical
MPa MPa
Temper t % %
value
mm min. max. min. max. min. min.
HBW
T4, T4510,
≤ 25 370 - 250 - 8 6 95
c
T4511
Extruded profile
Hardness
R R
m p0,2
Wall thickness
A A
50 mm
Typical
MPa MPa
Temper t % %
value
mm min. max. min. max. min. min.
HBW
T4, T4510,
≤ 30 370 - 250 - 8 6 95
c
T4511
a
D = Diameter for round bar.
b
S = Width across flats for square and hexagonal bar, thickness for rectangular bar.
c
Properties may be obtained by press quenching.
oSIST prEN 755-2:2023
EN 755-2:2023 (E)
Table 6 — Alloy EN AW-2011 [Al Cu6BiPb] and Alloy EN AW-2011A [Al Cu6BiPb(A)]
Extruded rod/bar
R
Dimensions Rm p0,2
A A
50 mm
Hardness
mm
MPa MPa
Temper
% %
Typical value
HBW
a b
D S min. min.
min. max. min. max.
c
T4 ≤ 200 ≤ 60 275 - 125 - 14 12 95
≤ 75 ≤ 60 310 - 230 - 8 6 110
c
T6
75 < D ≤ 200 - 295 - 195 - 6 - 110
Extruded tube
Wall thickness
R R A A
m p0,2 50 mm
Hardness
Temper t MPa MPa
% %
Typical value
HBW
mm min. max. min. max. min. min.
c
T6 ≤ 25 310 - 230 - 6 4 110
Extruded profile
Not specified
a
D = Diameter for round bar.
b
S = Width across flats for square and hexagonal bar, thickness for rectangular bar.
c
Properties may be obtained by press quenching.
oSIST prEN 755-2:2023
EN 755-2:2023 (E)
Table 7 — Alloy EN AW-2014 [Al Cu4SiMg] and Alloy EN AW-2014A [Al Cu4SiMg(A)]
Drawn rod/bar
Dimensions R R Hardness
m p0,2
A A
50 mm
Typical
mm
MPa MPa
Temper
% %
value
a b
D S min. max. min. max. min. min.
HBW
O, H111 ≤ 200 ≤ 200 - 250 - 135 12 10 45
≤ 25 ≤ 25 370 - 230 - 13 11 110
25 < D ≤ 75 25 < S ≤ 75 410 - 270 - 12 - 110
T4, T4510,
T4511
75 < D ≤ 150 75 < S ≤ 150 390 - 250 - 10 - 110
150 < D ≤ 200 150 < S ≤ 200 350 - 230 - 8 - 110
≤ 25 ≤ 25 415 - 370 - 6 5 140
25 < D ≤ 75 25 < S ≤ 75 460 - 415 - 7 - 140
T6, T6510,
75 < D ≤ 150 75 < S ≤ 150 465 - 420 - 7 - 140
T6511
150 < D ≤ 200 150 < S ≤ 200 430 - 350 - 6 - 140
200 < D ≤ 250
...