EN ISO 14577-3:2015

Metallic materials - Instrumented indentation test for hardness and materials parameters - Part 3: Calibration of reference blocks (ISO 14577-3:2015)

ISO 14577-3:2015 specifies a method for the calibration of reference blocks to use for the indirect verification of testing machines for the instrumented indentation test as specified in ISO 14577‑2:2015.

Metallische Werkstoffe - Instrumentierte Eindringprüfung zur Bestimmung der Härte und anderer Werkstoffparameter - Teil 3: Kalibrierung von Referenzproben (ISO 14577-3:2015)

Dieser Teil von ISO 14577 legt ein Verfahren zur Kalibrierung von Referenzproben, die bei der indirekten Prüfung von Prüfmaschinen nach ISO 14577-2:— verwendet werden, fest.
ANMERKUNG Die Referenzproben können entsprechend dem Anwendungsbereich der Prüfmaschine oder den zu ermittelnden Werkstoffparametern kalibriert werden.

Matériaux métalliques - Essai de pénétration instrumenté pour la détermination de la dureté et de paramètres des matériaux - Partie 3: Étalonnage des blocs de référence (ISO 14577-3:2015)

L'ISO 14577-3:2015 spécifie une méthode pour l'étalonnage des blocs de référence à utiliser pour la vérification indirecte des machines d'essai pour l'essai de pénétration instrumenté, telle que spécifiée dans l'ISO 14577‑2:2015.

Kovinski materiali - Instrumentirano vtiskanje pri preskušanju trdote in drugih lastnosti materialov - 3. del: Kalibracija referenčnih etalonov (ISO 14577-3:2015)

Ta del standarda ISO 14577 določa metodo za kalibracijo referenčnih etalonov, ki se uporabljajo pri posrednem preverjanju preskuševalnih strojev z instrumentiranim vtiskanjem, kot je določeno v standardu ISO 14577-2:2015.
OPOMBA: Referenčne etalone je mogoče umeriti v skladu s področjem uporabe preskuševalnih strojev ali z drugimi lastnostmi materialov, ki se ugotavljajo.

General Information

• Status: Published
• Publication Date: 28-Jul-2015
• Withdrawal Date: 30-Jan-2016
• ICS: 77.040.10 - Mechanical testing of metals
• Technical Committee: ECISS/TC 101 - Test methods for steel (other than chemical analysis)
• Drafting Committee: ECISS/TC 101 - Test methods for steel (other than chemical analysis)
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 29-Jul-2015
• Completion Date: 29-Jul-2015
• Ref Project: SIST EN ISO 14577-3:2015 - Metallic materials - Instrumented indentation test for hardness and materials parameters - Part 3: Calibration of reference blocks (ISO 14577-3:2015)

Relations

• Replaces: EN ISO 14577-3:2002 - Metallic materials - Instrumented indentation test for hardness and materials parameters - Part 3: Calibration of reference blocks (ISO 14577-3:2002)
• Effective Date: 18-Oct-2010

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 14577-3:2015
01-oktober-2015
1DGRPHãþD
SIST EN ISO 14577-3:2004
.RYLQVNLPDWHULDOL,QVWUXPHQWLUDQRYWLVNDQMHSULSUHVNXãDQMXWUGRWHLQGUXJLK
ODVWQRVWLPDWHULDORYGHO.DOLEUDFLMDUHIHUHQþQLKHWDORQRY,62
Metallic materials - Instrumented indentation test for hardness and materials parameters
- Part 3: Calibration of reference blocks (ISO 14577-3:2015)
Metallische Werkstoffe - Instrumentierte Eindringprüfung zur Bestimmung der Härte und
anderer Werkstoffparameter - Teil 3: Kalibrierung von Referenzproben (ISO 14577-
3:2015)
Matériaux métalliques - Essai de pénétration instrumenté pour la détermination de la
dureté et de paramètres des matériaux - Partie 3: Étalonnage des blocs de référence
(ISO 14577-3:2015)
Ta slovenski standard je istoveten z: EN ISO 14577-3:2015
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
SIST EN ISO 14577-3:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 14577-3:2015

---------------------- Page: 2 ----------------------

SIST EN ISO 14577-3:2015

EUROPEAN STANDARD
EN ISO 14577-3

NORME EUROPÉENNE

EUROPÄISCHE NORM
July 2015
ICS 77.040.10 Supersedes EN ISO 14577-3:2002
English Version
Metallic materials - Instrumented indentation test for hardness
and materials parameters - Part 3: Calibration of reference
blocks (ISO 14577-3:2015)
Matériaux métalliques - Essai de pénétration instrumenté Metallische Werkstoffe - Instrumentierte Eindringprüfung
pour la détermination de la dureté et de paramètres des zur Bestimmung der Härte und anderer Werkstoffparameter
matériaux - Partie 3: Étalonnage des blocs de référence - Teil 3: Kalibrierung von Referenzproben (ISO 14577-
(ISO 14577-3:2015) 3:2015)
This European Standard was approved by CEN on 16 April 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14577-3:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 14577-3:2015
EN ISO 14577-3:2015 (E)
Contents
Page
European foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 14577-3:2015
EN ISO 14577-3:2015 (E)
European foreword
This document (EN ISO 14577-3:2015) has been prepared by Technical Committee ISO/TC 164 “Mechanical
testing of metals” in collaboration with Technical Committee ECISS/TC 101 “Test methods for steel (other
than chemical analysis)” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2016, and conflicting national standards shall be withdrawn at
the latest by January 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 14577-3:2002.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Polan
...