EN ISO 8130-7:2019
(Main)Coating powders - Part 7: Determination of loss of mass on stoving (ISO 8130-7:2019)
Coating powders - Part 7: Determination of loss of mass on stoving (ISO 8130-7:2019)
This document specifies a method for the determination of loss of mass on stoving of coating powders that are to be applied by electrostatic spraying or flock spraying or fluidized bed.
The method described in this document is a simple, practical test which provides sufficiently accurate results for coating powders that lose approximately 2 % (by mass) on stoving (heating). Above 2 %, accuracy decreases with an increasing loss in mass.
This method determines the amount of all volatile matter, including water.
Thermogravimetric testing as described in the ISO 11358 series can be used as a comparative method.
Pulverlacke - Teil 7: Bestimmung des Einbrennverlustes (ISO 8130-7:2019)
Dieses Dokument legt ein Verfahren zum Bestimmen des Einbrennverlustes von Pulverlacken, die durch elektrostatisches Versprühen oder Beflockung oder Fluidisierbettverfahren aufzutragen sind, fest.
Das in diesem Dokument beschriebene Verfahren ist eine einfache praktische Prüfung, die bei Pulverlacken mit einem Einbrennverlust bis zu etwa 2 % (Massenanteil) ausreichend genaue Ergebnisse liefert. Oberhalb von 2 % nimmt die Genauigkeit mit zunehmendem Einbrennverlust ab.
Nach dem Verfahren wird der Gehalt an allen flüchtigen Anteilen einschließlich Wasser bestimmt.
Die thermogravimetrische Prüfung, wie in der Normenreihe ISO 11358 beschrieben, kann als Vergleichs-prüfung verwendet werden.
Poudres pour revêtement - Partie 7: Détermination de la perte de masse à la cuisson (ISO 8130-7:2019)
Le présent document spécifie une méthode de détermination de la perte de masse à la cuisson de poudres pour revêtement destinées à être appliquées par projection électrostatique, flocage ou lit fluidisé.
La méthode décrite dans le présent document constitue un essai simple et pratique donnant des résultats suffisamment exacts dans le cas de poudres pour revêtement dont la perte à la cuisson (chauffage) est d'environ 2 % (en masse). Au-delà de 2 %, l'exactitude diminue à mesure que la perte de masse augmente.
La présente méthode détermine la quantité de toutes les matières volatiles, y compris l'eau.
Un essai thermogravimétrique tel que décrit dans la série de l'ISO 11358 peut être utilisé à titre de méthode comparative.
Praškasti premazi - 7. del: Ugotavljanje izgube mase pri sušenju v peči (ISO 8130-7:2019)
Ta dokument določa metodo ugotavljanja izgube mase pri sušenju v peči praškastih premazov, ki se nanašajo z elektrostatičnim pršenjem, pršenjem kosmičev ali fluidizirano plastjo.
Metoda, opisana v tem dokumentu, je preprost praktični preskus, ki zagotavlja dovolj natančne rezultate za praškaste premaze, ki pri sušenju v peči (segrevanju) izgubijo približno 2 % mase. Nad 2 %
natančnost upada z naraščanjem izgube mase.
Ta metoda določa količino vseh hlapnih snovi, vključno z vodo.
Termogravimetrijsko preskušanje, kot je opisano v skupini standardov ISO 11358, je mogoče uporabiti kot primerjalno metodo.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 8130-7:2019
01-julij-2019
Nadomešča:
SIST EN ISO 8130-7:2013
Praškasti premazi - 7. del: Ugotavljanje izgube mase pri sušenju v peči (ISO 8130-
7:2019)
Coating powders - Part 7: Determination of loss of mass on stoving (ISO 8130-7:2019)
Pulverlacke - Teil 7: Bestimmung des Einbrennverlustes (ISO 8130-7:2019)
Poudres pour revêtement - Partie 7: Détermination de la perte de masse à la cuisson
(ISO 8130-7:2019)
Ta slovenski standard je istoveten z: EN ISO 8130-7:2019
ICS:
87.040 Barve in laki Paints and varnishes
SIST EN ISO 8130-7:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 8130-7:2019
---------------------- Page: 2 ----------------------
SIST EN ISO 8130-7:2019
EN ISO 8130-7
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2019
EUROPÄISCHE NORM
ICS 87.040 Supersedes EN ISO 8130-7:2010
English Version
Coating powders - Part 7: Determination of loss of mass on
stoving (ISO 8130-7:2019)
Poudres pour revêtement - Partie 7: Détermination de Pulverlacke - Teil 7: Bestimmung des
la perte de masse à la cuisson (ISO 8130-7:2019) Einbrennverlustes (ISO 8130-7:2019)
This European Standard was approved by CEN on 8 March 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8130-7:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 8130-7:2019
EN ISO 8130-7:2019 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 8130-7:2019
EN ISO 8130-7:2019 (E)
European foreword
This document (EN ISO 8130-7:2019) has been prepared by Technical Committee ISO/TC 35 "Paints
and varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2019, and conflicting national standards
shall be withdrawn at the latest by November 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8130-7:2010.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 8130-7:2019 has been approved by CEN as EN ISO 8130-7:2019 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 8130-7:2019
---------------------- Page: 6 ----------------------
SIST EN ISO 8130-7:2019
INTERNATIONAL ISO
STANDARD 8130-7
Second edition
2019-04
Coating powders —
Part 7:
Determination of loss of mass on
stoving
Poudres pour revêtement —
Partie 7: Détermination de la perte de masse à la cuisson
Reference number
ISO 8130-7:2019(E)
©
ISO 2019
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.