iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 15432:2008/AC:2010

(Corrigendum)

Winter and road service area maintenance equipments - Front-mounted equipments - Interchangeability

Winter and road service area maintenance equipments - Front-mounted equipments - Interchangeability

TC - Correction of Figure 3 in 3.1.5 in the three language versions.

Winterdienst- und Straßenbetriebsdienstausstattung - Mechanische Schnittstelle an Fahrzeugen für frontangebaute Maschinen - Austauschbarkeit

Matériels de viabilité hivernale et d'entretien des dépendances routières - Matériels montés à l'avant - Interchangeabilité

Oprema za vzdrževalna dela zimske službe in službe za vzdrževanje cest - Oprema za namestitev na sprednji del vozila - Zamenljivost

Ta evropski standard opredeljuje zahteve za različne elemente vozil za zagotavljanje zamenljivosti med vozilom in različno opremo, ki se namesti na sprednji del vozila. Opredeljuje določene dimenzije zamenljivosti plošče za namestitev na sprednji del vozila, vključno z njeno višino nad tlemi, kot tudi lokacije priklopnih naprav za električne in hidravlične povezave in za mehanski odjem moči (PTO). Ta evropski standard opredeljuje dva različna razreda plošč za montažo, z namenom pokriti cestna vozila z najvišjo načrtovano skupno maso, višjo od 3,5 t, največje možne raznolikosti (komercialna vozila, večnamenska vozila, komunalna vozila, ), ki so zmožna prevažati opremo za namestitev na sprednji del vozila za vzdrževalna dela zimske službe in službe za vzdrževanje cest.     Ta evropski standard opredeluje, glede na električne in hidravlične povezave in odjem moči, le lokacijska območja, območje čiščenja in preferenčno ureditev, da bi zagotovili zamenljivost. Zahteve, ki se nanašajo na vezne elemente, priklopne naprave in utorne gredi za odjem moči so podane v EN 15431. Normativni Dodatek A podaja določbe za izpopolnjen sistem priklopa na sprednji strani vozila, ki omogoča montažo in demontažo opreme brez uporabe orodja. Uporabniki, ki se morajo ukvarjati s posebnimi potrebami (npr. izredne vremenske razmere), bodo morda morali vozilo opremiti s takšnim avtomatskim priklopnim sistemom. Normativni Dodatek B podaja določbe za kompaktno in lahko ploščo za namestitev na sprednji del vozila, ki je namenjena kombinirani cestni in terenski uporabi.

General Information

Status
Withdrawn
Publication Date
22-Jun-2010
Withdrawal Date
19-Jul-2011
ICS
43.160 - Special purpose vehicles
Technical Committee
CEN/TC 337 - Winter maintenance and road service area maintenance equipment
Drafting Committee
CEN/TC 337/WG 3 - Interface between tools and vehicle
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
20-Jul-2011
Completion Date
20-Jul-2011
Ref Project
SIST EN 15432:2008/AC:2010 - Winter and road service area maintenance equipments - Front-mounted equipments - Interchangeability

Relations

Replaced By
EN 15432-1:2011 - Winter and road service area maintenance equipments - Front-mounted equipments - Part 1: Fixed front mounting plates
Effective Date
11-Jul-2011
Corrects
EN 15432:2008 - Winter and road service area maintenance equipments - Front-mounted equipments - Interchangeability
Effective Date
08-Jun-2022

Buy Standard

EN 15432:2008/AC:2010EN 15432:2008/AC:2010
PreviousNext
Corrigendum
EN 15432:2008/AC:2010
English language
2 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Oprema za vzdrževalna dela zimske službe in službe za vzdrževanje cest - Oprema za namestitev na sprednji del vozila - ZamenljivostWinterdienst- und Straßenbetriebsdienstausstattung - Mechanische Schnittstelle an Fahrzeugen für frontangebaute Maschinen - AustauschbarkeitMatériels de viabilité hivernale et d'entretien des dépendances routières - Matériels montés à l'avant - InterchangeabilitéWinter and road service area maintenance equipments - Front-mounted equipments - Interchangeability43.160Vozila za posebne nameneSpecial purpose vehiclesICS:Ta slovenski standard je istoveten z:EN 15432:2008/AC:2010SIST EN 15432:2008/AC:2010en,fr,de01-september-2010SIST EN 15432:2008/AC:2010SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 15432:2008/AC
June 2010
Juin 2010
Juni 2010 ICS 43.160 English version Version Française Deutsche Fassung
Winter and road service area maintenance equipments - Front-mounted equipments - Interchangeability
Matériels de viabilité hivernale et d'entretien des dépendances routières - Matériels montés à l'avant - Interchangeabilité
Winterdi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 15430-1:2015(Main)
Winter and road service area maintenance equipment - Data acquisition and transmission - Part 1: In-vehicle data acquisition
SIST EN 15430-1:2015

Same as in EN 15430-1:2007 + A1:2011

  • Standard
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15436-3:2015(Main)
Road service area maintenance equipment - Part 3: Classification
SIST EN 15436-3:2015

This document defines the classification criteria of the road service area maintenance equipment described in the scope of EN 15436 1 and used for:
-   grass cutting and brush cutting;
-   mechanical plant cutting.
This equipment is mounted on self-propelled carrying vehicles, and is intended, on the one hand, for cutting and shredding grass and brushwood, and, on the other hand, for trimming trees, saplings and bushes in road service areas. This document is intended to be used also in conjunction with FprEN 15436 2.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15436-2:2015(Main)
Road service area maintenance equipment - Part 2: Performance assessment
SIST EN 15436-2:2015

This European Standard specifies the accuracy of the performance measurement system of road service area maintenance equipment described in the scope of CEN/TC 337 and used for:
-   grass-cutting and brush-cutting;
-   mechanical plant-cutting.
This equipment is mounted on self-propelled carrying vehicles and is designed to cut and shred grass, brushwood, trees, saplings and bushes in road service areas.
This European Standard does not cover the collection and transportation of shredded grass.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15429-4:2015(Main)
Sweepers - Part 4: Symbols for operator controls and other displays
SIST EN 15429-4:2015

This European Standard applies to surface cleaning machines for outdoor applications in public areas, roads, airports and industrial complexes. Cleaning machines for winter maintenance and/or indoor applications are not included within the scope of this European Standard. Surface cleaning machines in terms of this standard, are self-propelled, truck mounted, attached sweeping equipment or pedestrian controlled as disclosed in EN 15429-1.
Surface cleaning machines by way of their function, have specialized equipment necessary to perform their task.
This European Standard deals with graphical symbols uniquely used to indicate the function and status of operator controls and tell-tale displays of the specialized equipment.
Common symbols that are included in other standards and applied to a wider range of machines are not included. Typically, symbols in this category that may equally be applied to surface cleaning machines can be found in ISO 2575 Road vehicles – Symbols for controls, indicators and tell-tales, and ISO 6405 Earth moving machinery – Symbols for operator and other displays – Part 1: Common Symbols.
This European Standard does not apply to machines or components that are specifically designed for cleaning tramlines and rail tracks.
Industrial sweepers, within the scope of EN 60335-2-72 are excluded from this European Standard.
This European Standard applies to machines manufactured after the approval date of the standard by CEN.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15429-3:2015(Main)
Sweepers - Part 3: Efficiency of particulate matter collection - Testing and Evaluation
SIST EN 15429-3:2015

This European Standard establishes a method to assess the PM10 and PM2,5 efficiency of road sweepers. PM10 and PM2,5 efficiency includes a sweeper’s ability to:
-   Remove and capture PM10 and PM2,5 particulate matter, and coarse size fractions, from typical urban road surfaces;
-   Minimize the amount of airborne and entrained PM10 and PM2,5 particulate matter resulting from the sweeping process.
The sweeper’s ability to remove and capture particulate matter and coarse size fractions is assessed using procedures and equipment to determine the amount of a test material (consisting of particulate matter and coarser size fractions) the sweeper is able to remove from a test surface during a controlled test run. This test measurement is used to calculate the removal efficiency for the sweeper.
The sweeper’s ability to minimize the amount of airborne and entrained particulate matter is also assessed using procedures and equipment to determine the airborne concentrations of PM10 and PM2,5 resulting from the sweeping of a test material (consisting of particulate matter and coarser size fractions) during a controlled test run. The test measurements are used to calculate PM10 and PM2,5 emission ratings for the sweeper.
This test allows the use of dust suppression water. Sweepers configured as flushing machines, or equipped with front-mounted spray bars which are not part of a dust suppression water system are not within the scope of this test.
The road sweeper’s performance results are reported in a quantitative numerical format that will allow comparative assessments of similarly classified sweepers. This test does not specify pass/fail criteria for the PM10 and PM2,5 efficiency measurements specified in the test procedure.
This test is applicable to truck mounted, self-propelled, towed and attached sweeping equipment as defined in EN 15429-1:2007, Clause 2.
This test is a model/type test, requiring the sweeper being tested to be representative of all factory production of that particular sweeper model.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15432-2:2013(Main)
Winter and road service area maintenance equipments - Front-mounted equipments - Part 2: Interchangeability on lifting systems
SIST EN 15432-2:2013

This European Standard specifies the requirements for elements mounted to carrying vehicles to ensure interchangeability between a vehicle and different equipments that are to be mounted frontally. It specifies certain interchangeability dimensions of the front mounting plate as well as the locations of coupling devices for electrical and hydraulic connections.
This European Standard specifies a mounting plate in order to cover road vehicles having a maximum total mass of up to 6,0 tons (commercial vehicles, multi purpose vehicles, communal vehicles, …) which are capable of carrying front mounted equipments for winter maintenance and for road service area maintenance. The mounting plate is designed to allow quick and easy changing of carrying vehicle equipments. Mounting or demounting of front-mounted equipments is generally effectuated by one person using conventional tools (mobile or fixed) prior to securing of the front-mounted equipment (by e.g. bolts or hydraulic element).
This European Standard does not specify vehicle-side lifting systems or receiving devices for mounting plate (device side).
The vehicle body guidelines from the vehicle manufacturer should be adhered to when performing any modifications to the vehicle.
This European Standard specifies, with regard to electrical and hydraulic connections, only location areas and clearance spaces in order to ensure interchangeability.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    11 pages
    German language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16330:2013(Main)
Winter and road service area equipment - Power system and related controls - Power hydraulic system and electric interfaces
SIST EN 16330:2014

This European Standard applies to power systems equipped for operation and to drive implements and attachments such as hydraulic driven front sweepers, mowers or suction sweepers on winter service vehicles or road service vehicles equipped with front-mounting plates according to EN 15432.
The purpose of this standard is to ensure interchangeability of vehicles and implements. The minimum requirements on the performance and the components of the hydraulic system, as well as the kind and the size of the connecting elements between the vehicle and the implement, are specified in the standard.
Clause 3 of this standard does not cover applications where the implements need a continuous hydraulic oil flow less than 45 l/ min.
Clause 4 is dealing with the electrical connection between vehicle and implement to drive an electrically driven hydraulic pump, used in trucks without hydraulic systems.
Clause 5 is dealing with a universal electrical connection used for front mounted mowers, spreaders and other road service area equipment with the following functions: power supply and transmitting CAN BUS signals.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15429-2:2012(Main)
Sweepers - Part 2: Performance requirements and test methods
SIST EN 15429-2:2013

This document applies to surface cleaning machines for outdoor applications in public areas, roads, airports and industrial complexes. Cleaning machines for winter maintenance and/or indoor applications are not included within the scope of this European Standard. Surface cleaning machines in terms of this standard, are self-propelled, truck mounted, attached sweeping equipment or pedestrian controlled.
This standard deals with the performance and functional characteristics and the test methods applied to the sweeping equipment when used as intended and under the conditions foreseen by the manufacturer.
This document does not include carrier vehicles (e.g. trucks). These are covered in national or EU Directives for vehicles.
This document does not apply to road surface cleaning equipment that would be front mounted on tractors according to EN 13524, or other vehicles.
This standard does not apply to machines or components that are specifically designed for cleaning tramlines and rail tracks.
This standard does not cover noise emission or any overload protection as these are covered by regulatory requirements.
Industrial sweepers, within the scope of EN 60335-2-72 are excluded from this standard.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15583-2:2012(Main)
Winter maintenance equipment - Snow ploughs - Part 2: Testing criteria and their requirements
SIST EN 15583-2:2012

This document is valid for snow ploughs designed to be fitted to winter maintenance vehicles on their front-mounting plates according to EN 15432 and also for side-mounted snow ploughs.
Requirements regarding the testing of override security systems and/or bump security systems of front-mounted or side-mounted snow ploughs for winter service are determined by this document. This document is meant to assess the demands made on snow ploughs operated in traffic.
The document is valid for:
-   single-side snow ploughs;
-   variable V-ploughs.
The following points are not standardized by this document:
-   V-shaped snow ploughs;
-   requirements for registration and approval;
-   requirements made by carrier vehicle manufacturers;
-   requirements on safety – these are dealt with in EN 13021.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15906:2011(Main)
Winter maintenance equipment - Snow removal machines with rotating tools - Specification and clearing capacity
SIST EN 15906:2012

This European Standard specifies requirements for snow removal machines with rotating tools for winter application on traffic areas. It is valid for design and construction. It also includes the minimum requirement concerning contents of the operating instructions.
This European Standard applies to:
   snow blowers;
   snow cutters;
   snow cutter blowers;
and related products such as side blowers, side cutters, etc.
This European Standard does not apply for:
   requirements for registration and approval;
   vehicle manufacturer requirements;
   safety requirements.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day