iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 16146:2012

(Main)

Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification

Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification

This European Standard applies to hoses for extractable outlets of any material intended for equipping sanitary tapware for sinks and basins. Such hoses will only be connected downstream of the obturator of the tapware. The tapware will comply with EN 200, EN 817, EN 1111, EN 1286 or EN 1287 (see [1], [2], [3], [5] and [6]).
Hoses intended to connect sanitary tapware to the water supplies are not covered by this standard.
This European Standard specifies:
-   the dimensional, mechanical and hydraulic characteristics with which the hose for extractable outlets shall comply;
-   the procedures for testing these characteristics.
Details of pressures and temperatures are given in Table 1.

Sanitärarmaturen - Ausziehbare Brauseschläuche für Sanitärarmaturen für Wasserversorgungssysteme vom Typ 1 und Typ 2 - Allgemeine technische Spezifikation

Die vorliegende Norm gilt unabhängig vom verwendeten Werkstoff für Schläuche für ausziehbare Ausläufe, die als Ausrüstung von Sanitärarmaturen für Wasch- und Spülbecken vorgesehen sind. Sie dürfen nur nach dem Absperrorgan der Armatur angeschlossen werden. Die Armatur muss EN 200, EN 817, EN 1111, EN 1286 oder EN 1287 entsprechen (siehe [1], [2], [3], [5], und [6]).
Diese Norm deckt keine Schläuche zur Verbindung der Sanitärarmaturen mit der Wasserversorgung ab.
Diese Europäische Norm legt Folgendes fest:
   die Abmessungen sowie die mechanischen und hydraulischen Eigenschaften, die Schläuche für ausziehbare Ausläufe aufweisen müssen;
   die Verfahren zur Prüfung dieser Eigenschaften.
Einzelheiten zu Druck und Temperatur sind in Tabelle 1 enthalten.

Robinetterie sanitaire - Flexibles de douchettes extractibles pour robinetterie sanitaire pour les systèmes d'alimentation en eau de types 1 et 2 - Spécifications techniques générales

La présente Norme européenne s’applique aux flexibles pour douchettes extractibles, quel que soit le matériau utilisé, destinés à équiper les robinetteries sanitaires des éviers et lavabos. Il convient que de tels flexibles ne soient raccordés qu’en aval de l’obturateur de la robinetterie. La robinetterie sera conforme à l’EN 200, l’EN 817, l’EN 1111, l’EN 1286 ou l’EN 1287 (voir [1], [2], [3], [5] et [6]).
Les flexibles destinés à relier la robinetterie sanitaire à l’alimentation en eau ne sont pas couverts par cette norme.
La présente Norme européenne prescrit :
   les caractéristiques dimensionnelles, de comportement mécanique et hydraulique auxquelles doivent répondre les flexibles pour douchettes extractibles ;
   les modes opératoires d’essai permettant de contrôler ces caractéristiques.

Sanitarne armature - Izvlečljive gibke cevi za sanitarne armature sistemov za oskrbo z vodo tipa 1 in tipa 2 - Splošne tehnične zahteve

Ta evropski standard velja za cevi izvlečljivih priključkov iz katerega koli materiala, ki so namenjene opremljanju sanitarnih armatur za umivalnike in pomivalna korita. Take cevi je treba priključiti za tesnilom sanitarne armature. Sanitarna armatura mora biti v skladu s standardi EN 200, EN 817, EN 1111, EN 1286 ali EN 1287 (glej [1], [2], [3], [5] in [6]). Cevi, namenjene priklopu sanitarnih armatur na dovod vode, niso zajete v tem standardu. Ta evropski standard določa: – mere in mehanske ter hidravlične značilnosti, s katerimi morajo biti skladne cevi za izvlečljive priključke; – postopke za preskušanje teh značilnosti. Podrobnosti glede tlaka in temperature so navedene v preglednici 1.

General Information

Status
Withdrawn
Publication Date
18-Dec-2012
Withdrawal Date
11-Nov-2014
ICS
91.140.70 - Sanitary installations
Technical Committee
CEN/TC 164 - Water supply
Drafting Committee
CEN/TC 164/WG 8 - Sanitary tapware
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
12-Nov-2014
Ref Project
SIST EN 16146:2013 - Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification

Relations

Merged Into
EN 16146:2012+A1:2014 - Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification
Effective Date
18-Jan-2023
Amended By
EN 16146:2012/FprA1 - Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification
Effective Date
25-Dec-2013

Buy Standard

EN 16146:2013EN 16146:2013
PreviousNext
Standard
EN 16146:2013
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sanitärarmaturen - Ausziehbare Brauseschläuche für Sanitärarmaturen für Wasserversorgungssysteme vom Typ 1 und Typ 2 - Allgemeine technische SpezifikationRobinetterie sanitaire - Flexibles de douchettes extractibles pour robinetterie sanitaire pour les systèmes d'alimentation en eau de types 1 et 2 - Spécifications techniques généralesSanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification91.140.70Sanitarne napraveSanitary installationsICS:Ta slovenski standard je istoveten z:EN 16146:2012SIST EN 16146:2013en,fr,de01-december-2013SIST EN 16146:2013SLOVENSKI
STANDARD



SIST EN 16146:2013



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16146
December 2012 ICS 91.140.70 English Version
Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification
Robinetterie sanitaire - Flexibles de douchettes extractibles pour robinetterie sanitaire pour les systèmes d'alimentation en eau de types 1 et 2 - Spécifications techniques générales
Sanitärarmaturen - Ausziehbare Brauseschläuche für Sanitärarmaturen für Wasserversorgungssysteme vom Typ 1 und Typ 2 - Allgemeine technische Spezifikation This European Standard was approved by CEN on 10 November 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16146:2012: ESIST EN 16146:2013



EN 16146:2012 (E) 2 Contents Page Foreword . 3 Introduction . 4 1 Scope . 5 2 Normative references . 8 3 Terms and definitions . 8 4 Designation . 8 5 Marking . 8 6 Materials . 9 6.1 Chemical and hygienic requirements . 9 6.2 Exposed surface condition and quality of coating . 9 7 Dimensional characteristics . 9 7.1 General . 9 7.2 Connecting dimensions . 9 7.3 Special cases . 10 8 Hydraulic characteristics .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 15091:2024(Main)
Sanitary tapware - Electronic opening and closing sanitary tapware
SIST EN 15091:2024

The purpose of this document is to specify requirements for marking, identification, leaktightness, electrical and operational safety and mechanical resistance for sanitary tapware with opening and closing controlled electronically.
The conditions of use for the supply system type are specified in Table 2:
[Table 2]
Annex B lists possible consequences of using a product outside its recommended operating range.
[Figure 1]
[Figure 2]

  • Draft
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 200:2023(Main)
Sanitary tapware - Single taps and combination taps for water supply systems of type 1 and type 2 - General technical specification
SIST EN 200:2024

This document specifies:
a)   the field of application for pillar taps, bib taps, single and multi-hole combination taps for use in:
1)   a supply system of Type 1 (see Figure 1) with a pressure range of (0,05 to 1,0) MPa [(0,5 to 10) bar];
2)   a supply system of Type 2 (see Figure 2) with a pressure range of (0,01 to 1,0) MPa [(0,1 to 10) bar];
b)   the dimensional, leak tightness, pressure resistance, hydraulic performance, mechanical strength, endurance, corrosion resistance of the surface of the product, sequence of testing and acoustic characteristics with which sanitary tapware products including their components (flexible hose, pullout spray) need to comply where applicable;
c)   test methods to verify the characteristics.
The tests described in this document are type tests (laboratory tests) and not quality control or factory production control (FPC) tests carried out during manufacture.
This document is applicable to draw-off taps (single taps and combination taps) for use with sanitary appliances installed in rooms used for personal hygiene (cloakrooms, bathrooms etc.) and for food preparation (kitchens), i.e. for use with baths, basins, bidets, showers and sinks.
This document applies to sanitary draw-off taps of nominal size 3/8”, 1/2", 3/4" and 1” (PN 10).
The conditions of use and classifications are given in Table 1.
Table 1 - Conditions of use
[ table not reproduced here ]
[ figure not reporduced here ]
Figure 1- Supply system of Type 1 with a pressure range of (0,05 to 1,0) MPa [(0,5 to 10) bar]
[ figure not reporduced here ]
Figure 2 - Supply system of Type 2 with a pressure range of (0,01 to 1,0) MPa [(0,1 to 10) bar]
NOTE   Components which are part or can be delivered with sanitary tapware products are listed in Annex C.
Final materials included in the product are not covered by this document.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 246:2021(Main)
Sanitary tapware - General specifications for aerators
SIST EN 246:2022

This document specifies:
- the dimensional, mechanical, hydraulic and acoustic characteristics with which sanitary tapware aerators (with and without flow regulation) should comply;
- the procedures for testing these characteristics.
This document is applicable to:
- Sanitary tapware aerators intended to be mounted on tapware used with sanitary appliances in toilets, bathrooms and kitchens (e.g. single taps, combination tap assemblies, mechanical mixing valves, thermostatic mixing valves);
- Sanitary tapware aerators used under the following pressure and temperature conditions (see Table 1).
[Table 1: Conditions for the use of aerators]
NOTE 1   Sanitary tapware aerators can only be connected downstream of the obturator of the sanitary tapware product.
NOTE 2   For the purposes of brevity, sanitary tapware aerators will be detailed only as aerators in the rest of this document.
NOTE 3   The tests described in this document are type tests (laboratory tests) and not quality control tests carried out during manufacture.
NOTE 4   Aerator swivels are to be tested in combination with a specific aerator only and are therefore considered to be sanitary tapware accessories. (Testing of the stand-alone swivels is therefore not covered by the scope of this document. Where swivels are used they are considered to be part of the tapware constructions, e.g. for bidet taps).

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 816:2017(Main)
Sanitary tapware - Automatic shut-off valves PN 10
SIST EN 816:2017

This European Standard is applicable to single and mixer taps with automatic shut-off for use with sanitary appliances installed in washrooms.
It does not apply to urinal or WC flushing valves or valves which open automatically.
The purpose of this standard is to specify the marking, identification, chemical/hygiene, dimensional, leaktightness, pressure resistance, hydraulic, mechanical endurance, and acoustical characteristics of automatic shut-off tapware.
The tests described in all the standard are type tests (laboratory tests) and not quality control tests carried out during manufacture
The following conditions of pressure and temperature apply:
Table 1 - Conditions for the use of self closing tapware
(The pressures given are flow pressures)

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1287:2017(Main)
Sanitary tapware - Low pressure thermostatic mixing valves - General technical specification
SIST EN 1287:2017

This European Standard specifies general construction, performance and material requirements for PN 10 thermostatic mixing valves (TMV) and includes test methods for the verification of mixed water temperature performance at the point of use below 45 °C. This does not exclude the selection of higher temperatures where available. When these devices are used to provide anti-scald protection for children, elderly and disabled persons the mixed water temperature needs to be set at a suitable bathing temperature (body temperature - 38 °C) as children are at risk to scalding at lower temperatures than adults. This does not obviate the need for supervision of young children during bathing.
It applies to valves intended for use on sanitary appliances in kitchens, washrooms (incl. all rooms with sanitary tapware, e.g. toilet and cloakrooms) and bathrooms operating under the conditions specified in Table 1.
This standard allows TMVs to supply a single outlet or a small number of outlets in a "domestic" application (e.g. one valve, controlling a shower, bath, basin and/or, bidet), excluding valves specifically designed for supplying a large number of outlets (i.e. for institutional use).
The tests described are type tests (laboratory tests) and not quality control tests carried out during manufacture.
Table 1 - Conditions of use

  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1111:2017(Main)
Sanitary tapware - Thermostatic mixing valves (PN 10) - General technical specification
SIST EN 1111:2017

This European Standard specifies general construction, performance and material requirements for PN 10 thermostatic mixing valves (TMV) and includes test methods for the verification of mixed water temperature performance at the point of use below 45 °C. This does not exclude the selection of higher temperatures where available. When these devices are used to provide anti-scald protection for children, elderly and disabled persons the mixed water temperature needs to be set at a suitable bathing temperature (body temperature approximately 38 °C) as children are at risk to scalding at lower temperatures than adults. This does not obviate the need for supervision of young children during bathing.
It applies to valves intended for use on sanitary appliances in kitchens, washrooms (incl. all rooms with sanitary tapware, e.g. toilets and cloakrooms) and bath rooms operating under the conditions specified in Table 1.
This standard allows TMVs to supply a single outlet or a small number of outlets in a "domestic" application (e.g. one valve controlling a shower, bath, basin and/or bidet), excluding valves specifically designed for supplying a large number of outlets (i.e. for institutional use).
The tests described are type tests (laboratory tests) and not quality control tests carried out during manufacture.
Table 1 - Conditions of use

  • Standard
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1113:2015(Main)
Sanitary tapware - Shower hoses for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification
SIST EN 1113:2015

This European Standard specifies:
-   the dimensional, leaktightness, mechanical and hydraulic characteristics with which shower hoses should comply;
-   the procedures for testing these characteristics.
This European Standard applies to shower hoses of any material used for ablutionary purposes and intended for equipping and supplementing sanitary tapware for baths and showers.
This European Standard applies to shower hoses connected downstream of the obturator of the tapware.
Hoses which are an integral part of sanitary tapware (sink and wash basin mixing valves) or hoses intended to connect sanitary tapware to the water supplies are not covered by this European Standard.
Details of pressures and temperatures are given in Table 1.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16146:2012+A1:2014(Main)
Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification
SIST EN 16146:2013+A1:2015

This European Standard applies to hoses for extractable outlets of any material intended for equipping sanitary tapware for sinks and basins. Such hoses will only be connected downstream of the obturator of the tapware. The tapware will comply with EN 200, EN 817, EN 1111, EN 1286 or EN 1287 (see [1], [2], [3], [5] and [6]).
Hoses intended to connect sanitary tapware to the water supplies are not covered by this standard.
This European Standard specifies:
-   the dimensional, mechanical and hydraulic characteristics with which the hose for extractable outlets shall comply;
-   the procedures for testing these characteristics.
Details of pressures and temperatures are given in Table 1.
(...)

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16145:2012(Main)
Sanitary tapware - Extractable outlets for sink and basin mixers - General technical specification
SIST EN 16145:2013

This European Standard specifies:
-   the dimensional, leaktightness, mechanical, hydraulic and acoustic characteristics with which extractable outlets with or without spray mode selector function need to comply;
-   the procedures for testing these characteristics.
It applies to extractable outlets made from any material which is intended for equipping and supplementing sanitary tapware for sinks and wash-basins used for culinary or ablutionary purposes. Such extractable outlets shall only be connected downstream of the obturator of the tapware.
Extractable outlets with total closing device fitted after the obturator of the tapware are not covered by this standard. Such products will be tested in accordance with EN 200, EN 817, EN 1111, EN 1286 or EN 1287 (see [1], [2], [3], [5] and [6]).
The conditions of use and classification are specified in Table 1.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 817:2008(Main)
Sanitary tapware - Mechanical mixing valves (PN 10) - General technical specifications
SIST EN 817:2009

This European Standard specifies:
   the dimensional, leaktightness, pressure resistance, hydraulic performance, mechanical strength, endurance and acoustic characteristics with which mechanical mixing valves need to comply;
   test methods to verify the characteristics;
   the tests described in this European Standard are type tests (laboratory tests) and not quality control tests carried out during manufacture.
This European Standard applies to PN 10 mechanical mixing valves for use with sanitary appliances installed in rooms used for bodily hygiene (cloakrooms, bathrooms, etc.) and in kitchens, i.e. for use with baths, wash basins, bidets, showers and sinks.
The conditions of use and classifications are given in Table 1.
Table 1   - Conditions of use/classifications

  • Standard
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day