Grain-oriented electrical steel strip and sheet delivered in the fully processed state

This document defines the steel grades of grain-oriented electrical steel strip and sheet in nominal thicknesses of 0,20 mm, 0,23 mm, 0,27 mm, 0,30 mm and 0,35 mm. In particular, it gives general requirements, magnetic properties, geometric characteristics, tolerances and technological characteristics, as well as inspection procedures.
This document applies to Goss textured grain-oriented electrical steel strip and sheet supplied in the final annealed condition in coils or sheets and intended for the construction of magnetic circuits.
The grades are grouped into three classes:
- conventional grades;
- high permeability grades;
- magnetic domain refined high permeability grades.
They correspond to Class C22 of IEC 60404-1.

Kornorientiertes Elektroband und -blech im schlussgeglühten Zustand

Dieses Dokument legt die Stahlsorten für kornorientiertes Elektroband und -blech in Nenndicken 0,20 mm, 0,23 mm; 0,27 mm; 0,30 mm und 0,35 mm fest und im Besonderen allgemeine Anforderungen, magnetische Eigenschaften, geometrische Eigenschaften und Grenzabmaße, technologische Eigenschaften sowie Prüfbedingungen.
Dieses Dokument gilt für kornorientiertes Elektroband und -blech mit Goss-Textur, das im schlussgeglühten Zustand in Form von Rollen oder Tafeln geliefert wird und für den Bau magnetischer Kreise bestimmt ist.
Die Erzeugnisse sind in drei Klassen unterteilt:
- konventionelle Erzeugnisse;
- Erzeugnisse mit hoher Permeabilität;
- domainverfeinerte (gelaserte) Erzeugnisse mit hoher Permeabilität.
Diese entsprechen IEC 60404-1, Klasse C 22.

Bandes et tôles en acier électrique à grains orientés livrées à l'état fini

Le présent document définit les nuances d’acier des bandes et tôles en acier électriques à grains orientés d'épaisseurs nominales 0,20 mm, 0,23 mm, 0,27 mm, 0,30 mm et 0,35 mm. Il donne notamment les exigences générales, les caractéristiques magnétiques, les caractéristiques géométriques, les tolérances et les caractéristiques technologiques, ainsi que les modalités de contrôle.
Le présent document s’applique aux bandes et tôles en acier électrique à grains orientés, à texture de Goss, livrées à l’état de recuit final en couronnes ou en feuilles et destinées à la construction de circuits magnétiques.
Les nuances sont groupées en trois classes :
- nuances conventionnelles ;
- nuances à haute perméabilité ;
- nuances à haute perméabilité avec affinement des domaines magnétiques
Elles correspondent à la classe C.22 de l’IEC 60404-1.

Orientirana elektropločevina in trakovi, dobavljeni v končnem žarjenem stanju

Ta dokument določa vrste jekla za orientirano elektropločevino in trakove z nazivnimi debelinami 0,20 mm, 0,23 mm, 0,27 mm, 0,30 mm in 0,35 mm. Določa zlasti splošne zahteve, magnetne lastnosti, geometrijske lastnosti, tolerance, tehnološke lastnosti in postopke pregledovanja.
Ta dokument se uporablja za orientirano elektropločevino in trakove s teksturo Goss, ki so dobavljeni v končnem žarjenem stanju v obliki tuljav ali pločevine in namenjeni izdelavi magnetnih vezij.
Obstajajo trije razredi:
–   običajni razred;
–   razred z visoko prepustnostjo;
–   razred z visoko prepustnostjo, izboljšan z magnetno domeno.
Ti materiali ustrezajo razredu C22 iz standarda IEC 60404-1.

General Information

Status
Published
Publication Date
06-Sep-2022
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
07-Sep-2022
Due Date
28-Nov-2022
Completion Date
07-Sep-2022

Relations

Buy Standard

Standard
EN 10107:2022
English language
21 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-november-2022
Nadomešča:
SIST EN 10107:2014
Orientirana elektropločevina in trakovi, dobavljeni v končnem žarjenem stanju
Grain-oriented electrical steel strip and sheet delivered in the fully processed state
Kornorientiertes Elektroband und -blech im schlussgeglühten Zustand
Bandes et tôles en acier électrique à grains orientés livrées à l'état fini
Ta slovenski standard je istoveten z: EN 10107:2022
ICS:
77.140.50 Ploščati jekleni izdelki in Flat steel products and semi-
polizdelki products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 10107
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2022
EUROPÄISCHE NORM
ICS 77.140.50 Supersedes EN 10107:2014
English Version
Grain-oriented electrical steel strip and sheet delivered in
the fully processed state
Bandes et tôles en acier électrique à grains orientés Kornorientiertes Elektroband und -blech im
livrées à l'état fini schlussgeglühten Zustand
This European Standard was approved by CEN on 24 July 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10107:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Classification and designation . 7
4.1 Classification . 7
4.2 Designation . 7
5 Information to be supplied by the purchaser . 7
5.1 General . 7
5.2 Mandatory information . 7
5.3 Options . 8
6 General requirements . 8
6.1 Production process . 8
6.2 Form of supply . 8
6.3 Delivery condition . 9
6.4 Surface condition . 9
6.5 Suitability for cutting . 9
7 Technical requirements. 9
7.1 Magnetic properties . 9
7.2 Geometric characteristics and tolerances . 12
7.3 Technological characteristics . 14
8 Inspection and testing . 15
8.1 General . 15
8.2 Sampling . 15
8.3 Preparation of test specimens . 15
8.4 Test methods . 17
8.5 Retests . 18
9 Marking, labelling and packaging . 18
10 Complaints . 18
Annex A (informative) Maximum specific total loss at 60 Hz and 1,7 T . 19
Bibliography . 21

European foreword
This document (EN 10107:2022) has been prepared by Technical Committee CEN/TC 459 “ECISS –
European Committee for Iron and Steel Standardization” , the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2023, and conflicting national standards shall
be withdrawn at the latest by March 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10107:2014.
This edition includes the following significant technical changes with respect to the previous edition:
— insertion of a third class of electrical steels for magnetic domain refined high permeability grades;
— introduction of the Single Sheet Testing (SST) method as reference measurement method for this
third class of material together with a conversion factor for transposition of the SST measurement
results to the Epstein measurement results;
— update of the electrical steel range to take account of the current offers and demands of grades.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Through its sub-committee SC 8 “Steel sheet and strip for electrical applications” (secretariat: DIN).
Introduction
The insertion of a third class of electrical steels for magnetic domain refined high permeability grades is
the main reason of this revision. Most of the technologies of magnetic domain refinement result in
material that does not withstand the stress relief annealing after cutting without changing the magnetic
properties (i.e. the specific total loss). In the case of this material, the Epstein method according to
EN 60404-2, requiring the annealing of the Epstein strip samples, is not suitable. Therefore, the Single
Sheet Tester (SST) method specified in IEC 60404-3 is employed.
The introduction of the SST as the reference measurement method for these magnetic domain refined
high permeability grades was preceded by intense discussions within IEC/TC 68.
The specific total loss measured by use of the SST specified in IEC 60404-3 tends to be larger than the
value measured by the use of Epstein frame in accordance with EN 60404-2. The magnetic polarization
at H = 800 A/m measured by use of the SST tends to be a little lower than the value measured by the use
of Epstein frame.
The significant difference between Epstein and SST loss results made it necessary to introduce a
Conversion Factor, F , applied to the SST results. This Conversion Factor is to create continuity in the
c
quality characteristics ratio of conventional grain-oriented electrical steel grades and of high
permeability grades (Epstein related loss values) to the magnetic domain refined high permeability
grades (SST related loss values), particularly over the transition zone between these grades. Otherwise,
it might be confusing to the users of this specification standard that the higher quality materials
measured by the SST method are listed with seemingly higher values of the specific total loss, compared
with the lower Epstein values measured on the lower quality grades.
Considerations of the widely spread grades of grain-oriented electrical steel led to the consented value
of F = 0,925 to be applied to the loss values at 1,7 T measured by the SST method.
c
The magnetic polarization for H = 800 A/m is the value taken from the SST measurement without
conversion to an equivalent Epstein value.
Consequently, the magnetic domain refined high permeability grades have been listed in a new
Table 3 as a new class of grain-oriented electrical steel strip and sheet.
1 Scope
This document defines the steel grades of grain-oriented electrical steel strip and sheet in nominal
thicknesses of 0,20 mm, 0,23 mm, 0,27 mm, 0,30 mm and 0,35 mm. In particular, it gives general
requirements, magnetic properties, geometric characteristics, tolerances and technological
characteristics, as well as inspection procedures.
This document applies to Goss textured grain-oriented electrical steel strip and sheet supplied in the
final annealed condition in coils or sheets and intended for the construction of magnetic circuits.
The grades are grouped into three classes:
— conventional grades;
— high permeability grades;
— magnetic domain refined high permeability grades.
They correspond to Class C22 of IEC 60404-1.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 10021, General technical delivery conditions for steel products
EN 10204, Metallic products - Types of inspection documents
EN 10251, Magnetic materials - Methods of determination of the geometrical characteristics of electrical
steel sheet and strip
EN 60404-2, Magnetic materials - Part 2: Methods of measurement of the magnetic properties of electrical
steel strip and sheet by means of an Epstein frame
EN IEC 60404-11, Magnetic materials - Part 11: Methods of measurement of the surface insulation
resistance of electrical steel strip and sheet
EN IEC 60404-13, Magnetic materials - Part 13: Methods of measurement of resistivity, density and
stacking factor of electrical steel strip and sheet
EN ISO 7799, Metallic materials - Sheet and strip 3 mm thick or less - Reverse bend test (ISO 7799)
IEC 60050-121, International electrotechnical vocabulary — Part 121: Electromagnetism
IEC 60050-221, International electrotechnical vocabulary — Part 221: Magnetic materials and
components
IEC 60404-3, Magnetic materials — Part 3: M
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.