EN 10107:2014

Grain-oriented electrical steel strip and sheet delivered in the fully processed state

This European Standard defines the steel grades of grain-oriented electrical strip and sheet in nominal thicknesses of 0,23 mm, 0,27 mm, 0,30 mm and 0,35 mm and specifies in particular, general requirements, magnetic properties, geometric characteristics and tolerances and technological characteristics, as well as inspection procedures.
This European Standard applies to Goss textured grain-oriented electrical strip and sheet supplied in the final annealed condition in sheets or coils, and intended for the construction of magnetic circuits.
The materials are grouped into two classes:
a)   conventional grain oriented material;
b)   high permeability grain oriented material.
They correspond to Clause C.22 of IEC 60404-1:2000.

Kornorientiertes Elektroband und -blech im schlussgeglühten Zustand

Dieses Dokument legt die Stahlsorten für kornorientiertes Elektroband und -blech in den  Nenndicken 0,23 mm, 0,27 mm, 0,30 mm und 0,35 mm fest und im Besonderen allgemeine Anforderungen, magnetische Eigenschaften, geometrische Eigenschaften und Grenzabmaße, technologische Eigenschaften sowie Prüfbe-dingungen.
Diese Europäische Norm gilt für kornorientiertes Elektroband und -blech mit Goss-Textur, das im schlussgeglühten Zustand in Form von Tafeln oder Rollen geliefert wird und für den Bau magnetischer Kreise bestimmt ist.
Die Erzeugnisse sind in zwei Klassen, nach IEC 60404-1:2000 Abschnitt C22, wie folgt unterteilt:
a)   konventionelle kornorientierte Erzeugnisse;
b)   kornorientierte Erzeugnisse mit hoher Permeabilität.

Bandes et tôles en acier électrique à grains orientés livrées à l'état fini

La présente Norme européenne définit les nuances d’acier des bandes et tôles électriques à grains orientés d'épaisseurs nominales 0,23 mm, 0,27 mm, 0,30 mm et 0,35 mm, et spécifie en particulier les prescriptions générales, les caractéristiques magnétiques, les caractéristiques et tolérances géométriques et les caractéristiques technologiques ainsi que les modalités de contrôle.
La présente Norme européenne s’applique aux bandes et tôles en acier électrique à grains orientés, à texture de Goss, livrées à l’état de recuit final en bandes ou en feuilles et destinées à la construction de circuits magnétiques.
Les matériaux sont groupés en deux classes :
a)   matériau à grains orientés, conventionnel ;
b)   matériau à grains orientés, à haute perméabilité.
Ils correspondent à l'Article C.22 de la CEI 60404-1:2000.

Orientirana elektropločevina in trakovi, dobavljeni v končnem žarjenem stanju

Standard EN 10107 določa vrste jekla za orientirano elektropločevino in trakove z nazivnimi debelinami 0,23 mm, 0,27 mm, 0,30 mm in 0,35 mm ter posebej določa splošne zahteve, magnetne lastnosti, geometrijske lastnosti in tolerance ter tehnološke lastnosti in postopke pregledovanja. Ta evropski standard velja za elektropločevino in trak s teksturo Goss, dobavljen v končnem žarjenem stanju v obliki pločevine ali tuljav, in je namenjen konstruiranju magnetnih krogov. Materiali so razvrščeni v dva razreda: a) konvencionalni orientirani material, b) orientirani material z visoko prepustnostjo. Ti materiali ustrezajo točki C.22 iz standarda IEC 60404-1: 2000.

General Information

• Status: Withdrawn
• Publication Date: 25-Mar-2014
• Withdrawal Date: 06-Sep-2022
• ICS: 77.140.50 - Flat steel products and semi-products
• Technical Committee: ECISS/TC 108 - Steel sheet and strip for electrical applications
• Drafting Committee: ECISS/TC 108 - Steel sheet and strip for electrical applications
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 07-Sep-2022
• Ref Project: SIST EN 10107:2014 - Grain-oriented electrical steel strip and sheet delivered in the fully processed state

Relations

• Replaces: EN 10107:2005 - Grain-oriented electrical steel sheet and strip delivered in the fully processed state
• Effective Date: 08-Jun-2022
• Replaced By: EN 10107:2022 - Grain-oriented electrical steel strip and sheet delivered in the fully processed state
• Effective Date: 14-Sep-2022

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kornorientiertes Elektroband und -blech im schlussgeglühten ZustandBandes et tôles et magnétiques en acier à grains orientés livrées à l'état finiGrain-oriented electrical steel strip and sheet delivered in the fully processed state77.140.50SROL]GHONLFlat steel products and semi-productsICS:Ta slovenski standard je istoveten z:EN 10107:2014SIST EN 10107:2014en,fr,de01-julij-2014SIST EN 10107:2014SLOVENSKI
STANDARDSIST EN 10107:20051DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10107
March 2014 ICS 77.140.50 Supersedes EN 10107:2005English Version
Grain-oriented electrical steel strip and sheet delivered in the fully processed state
Bandes et tôles magnétiques en acier à grains orientés livrées à l'état fini
Kornorientiertes Elektroband und -blech im schlussgeglühten Zustand This European Standard was approved by CEN on 6 February 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10107:2014 ESIST EN 10107:2014

Foreword .3 1 Scope .4 2 Normative references .4 3 Terms and definitions .5 4 Classification and designation .5 4.1 Classification .5 4.2 Designation .5 5 Information to be supplied by the purchaser .6 5.1 Mandatory information .6 5.2 Options .6 6 General requirements .7 6.1 Production process .7 6.2 Form of supply .7 6.3 Delivery condition .7 6.4 Surface condition.7 6.5 Suitability for cutting .7 7 Technical requirements .8 7.1 Magnetic properties .8 7.1.1 General .8 7.1.2 Magnetic polarization .8 7.1.3 Specific total loss .8 7.2 Geometric characteristics and tolerances . 10 7.2.1 Thickness . 10 7.2.2 Width . 11 7.2.3 Length . 11 7.2.4 Edge camber . 11 7.2.5 Flatness (wave factor) . 12 7.2.6 Residual curvature. 12 7.2.7 Burr height . 12 7.3 Technological characteristics . 12 7.3.1 Density . 12 7.3.2 Stacking factor . 12 7.3.3 Number of bends . 12 7.3.4 Internal stresses . 12 7.3.5 Insulation coating resistance . 12 8 Inspection and testing . 12 8.1 General . 12 8.2 Sampling . 13 8.3 Preparation of test specimens . 13 8.3.1 Magnetic properties . 13 8.3.2 Geometrical characteristics and tolerances . 13 8.3.3 Technological characteristics . 14 8.4 Test methods . 14 8.4.1 General . 14 8.4.2 Magnetic properties . 14 8.4.3 Geometrical characteristics and tolerances . 15 8.4.4 Technological characteristics . 15 8.5 Retests . 16 9 Marking, labelling and packaging . 16 10 Complaints . 16 Annex A (informative)
Maximum specific total loss at 60 Hz and 1,7 T . 17 Bibliography . 18 SIST EN 10107:2014
...