iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 61881-3:2012/A1:2013

(Amendment)

Railway applications - Rolling stock equipment - Capacitors for power electronics - Part 3: Electric double-layer capacitors

Railway applications - Rolling stock equipment - Capacitors for power electronics - Part 3: Electric double-layer capacitors

This part of IEC 61881 applies to d.c. electric double-layer capacitors (cell, module and bank) for power electronics intended to be used on rolling stock. This standard specifies quality requirements and tests, safety requirements, and describes installation and operation information. NOTE Example of the application for capacitors specified in this Standard; d.c. energy storage, etc. Capacitors not covered by this Standard: - IEC 61881-1: Paper/plastic film capacitors; - IEC 61881-2: Aluminium electrolytic capacitors with non-solid electrolyte. Guidance for installation and operation is given in Clause 9.

Bahnanwendungen - Betriebsmittel auf Bahnfahrzeugen - Kondensatoren für Leistungselektronik - Teil 3: Doppelschichtkondensatoren

Applications ferroviaires - Matériel roulant - Condensateurs pour électronique de puissance - Partie 3: Condensateurs électriques à double couche

Železniške naprave - Oprema voznih sredstev - Kondenzatorji za močnostno elektroniko - 3. del: Električni dvoplastni kondenzatorji - Dopolnilo A1 (IEC 61881-3:2012/A1:2013)

Ta del standarda IEC 61881 se nanaša na električne dvoplastne kondenzatorje (celice, module ali banke) z enosmerno napetostjo za močnostno elektroniko, ki se uporablja pri železniških voznih sredstvih. Ta standard določa zahteve kakovosti in preskusov, varnostne zahteve ter vsebuje navodila za namestitev in uporabo. OPOMBA Primer uporabe za kondenzatorje, ki so določeni v tem standardu; shranjevanje energije z enosmerno napetostjo idr. Kondenzatorji, ki niso zajeti v standardu: - IEC 61881-1: papirnati/plastični film kondenzatorji; - IEC 61881-2: aluminijski elektrolitski kondenzatorji z elektrolitom, ki ni v trdem stanju. Navodila za namestitev in uporabo so podana v 9. členu.

General Information

Status
Published
Publication Date
07-Nov-2013
Withdrawal Date
20-Oct-2016
ICS
45.060 - Railway rolling stock
Technical Committee
CLC/TC 9X - Electrical and electronic applications for railways
Drafting Committee
CLC/SC 9XB - Electromechanical material on board rolling stock
Current Stage
6060 - Document made available - Publishing
Start Date
08-Nov-2013
Completion Date
08-Nov-2013
Ref Project
SIST EN 61881-3:2012/A1:2014 - Railway applications - Rolling stock equipment - Capacitors for power electronics - Part 3: Electric double-layer capacitors

Relations

Amends
EN 61881-3:2012 - Railway applications - Rolling stock equipment - Capacitors for power electronics - Part 3: Electric double-layer capacitors
Effective Date
29-Jan-2023

Buy Standard

EN 61881-3:2012/A1:2014EN 61881-3:2012/A1:2014
PreviousNext
Amendment
EN 61881-3:2012/A1:2014
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61881-3:2012/A1:2014
01-januar-2014
äHOH]QLãNHQDSUDYH2SUHPDYR]QLKVUHGVWHY.RQGHQ]DWRUML]DPRþQRVWQR
HOHNWURQLNRGHO(OHNWULþQLGYRSODVWQLNRQGHQ]DWRUML'RSROQLOR$ ,(&
$
Railway applications - Rolling stock equipment - Capacitors for power electronics - Part
3: Electric double-layer capacitors
Bahnanwendungen - Betriebsmittel auf Bahnfahrzeugen - Kondensatoren für
Leistungselektronik - Teil 3: Doppelschichtkondensatoren
Applications ferroviaires - Matériel roulant - Condensateurs pour électronique de
puissance - Partie 3: Condensateurs électriques à double couche
Ta slovenski standard je istoveten z: EN 61881-3:2012/A1:2013
ICS:
31.060.70 0RþQRVWQLNRQGHQ]DWRUML Power capacitors
45.040 Materiali in deli za železniško Materials and components
tehniko for railway engineering
SIST EN 61881-3:2012/A1:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61881-3:2012/A1:2014

---------------------- Page: 2 ----------------------

SIST EN 61881-3:2012/A1:2014

EUROPEAN STANDARD
EN 61881-3/A1

NORME EUROPÉENNE
November 2013
EUROPÄISCHE NORM

ICS 45.060


English version


Railway applications -
Rolling stock equipment -
Capacitors for power electronics -
Part 3: Electric double-layer capacitors
(IEC 61881-3:2012/A1:2013)


Applications ferroviaires -  Bahnanwendungen -
Matériel roulant - Betriebsmittel auf Bahnfahrzeugen -
Condensateurs pour électronique Kondensatoren für Leistungselektronik -
de puissance - Teil 3: Doppelschichtkondensatoren
Partie 3: Condensateurs électriques (IEC 61881-3:2012/A1:2013)
à double couche
(CEI 61881-3:2012/A1:2013)



This amendment A1 modifies the European Standard EN 61881-3:2012; it was approved by CENELEC on 2013-
10-21. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate
the conditions for giving this amendment the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61881-3:2012/A1:2013 E

---------------------- Page: 3 ----------------------

SIST EN 61881-3:2012/A1:2014
EN 61881-3:2012/A1:2013 - 2 -

Foreword
The text of document 9/1819/FDIS, future IEC 61881-3:2012/A1, prepared by IEC/TC 9 "Electrical
equipment and systems for railways" was submitted to the IEC-CENELEC parallel vote and approved
by CENELEC as EN 61881-3:2012/A1:2013.

The following dates are fixed:
(dop) 2014-07-21
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2016-10-21
• latest date by which the national
standards conflicting with the
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.

Endorsement notice
The text of the International Standard IEC 61881-3:2012/A1:2013 was approved by CENELEC as a
European Standard without any modification.
In the Bibliography of EN 61881-3:2012, the following note has to be added for the standard indicated:

IEC 60529 NOTE Harmonized as EN 60529.

---------------------- Page: 4 ----------------------

SIST EN 61881-3:2012/A1:2014



IEC 61881-3

®


Edition 1.0 2013-09




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE




AMENDMENT 1

AMENDEMENT 1





Railway applications – Rolling stock equipment – Capacitors for power

electronics –

Part 3: E
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 62847:2023(Main)
Railway applications - Rolling stock - Electrical connectors - Requirements and test methods
SIST EN IEC 62847:2023

This International Standard retains IEC 61984:2008 as the minimum performance requirements for railway rolling stock electrical connectors. It identifies additional terms, test methods and performance requirements for single-pole and multipole connectors with rated voltages up to 1 000 V, rated currents up to 125 A per contact and frequencies below 3 MHz used for indoor and outdoor applications in railway rolling stock. This International Standard does not cover: - connectors with breaking capacity (CBCs) as defined in IEC 61984:2008, 3.2, because on board rolling stock connectors are not intended to be operated (i.e. mated and unmated) under load or when live, either by means of procedures or by the presence of interlocks, as required by IEC 61991; - non-rewirable connectors as defined in IEC 61984:2008, 3.5; - automatic couplers, due to their additional mechanical complexity and the need for more specific requirements and testing; - inter-vehicle jumpers, as they are connector and cable assemblies whose characteristics depend on those of both elements. Inter-vehicle connectors within the limits set in the scope of this International Standard are therefore covered by the agreed choice of suitable mechanical and environmental characteristics as defined by Annex B, and suggested by Annex C. This International Standard identifies the application levels for electrical connectors based on a) the severity of the service conditions in different rolling stock technologies, b) the intended use of the rolling stock, c) the location of the connector in the rolling stock system. This International Standard is not applicable to internal connections of electronic devices such as connectors for printed boards and rack-and-panel connectors.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61133:2021(Main)
Railway applications - Rolling stock - Testing of rolling stock on completion of construction and before entry into service
SIST EN IEC 61133:2022

To replace EN 50215:2009 with IEC 61133:2016 according to SC9XB Decision 53/09

  • Standard
    70 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60077-5:2019(Main)
Railway applications - Electric equipment for rolling stock - Part 5: Electrotechnical components - Rules for HV fuses
SIST EN IEC 60077-5:2020

IEC 60077-5:2019 is available as IEC 60077-5:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60077-5:2019 give additional or amended rules for high voltage (HV) fuses as a supplement to those given by IEC 60077-2. The high voltage fuses concerned are those connected into power and/or auxiliary circuits. The nominal voltage of these circuits lies between 600 V DC and 3 000 V DC, according to IEC 60850. These fuses can also be used in auxiliary AC circuits up to a nominal voltage of 1 500 V. This document together with IEC 60077-2 states specifically: a) the characteristics of the fuses; b) the service conditions with which the fuses comply with reference to: - operation and behaviour in normal service; - operation and behaviour in case of short circuit; - dielectric properties. c) the tests intended for confirming the compliance of the fuse with the characteristics under the service conditions and the methods adopted for these tests; d) the information marked on, or given with, the fuse. This second edition cancels and replaces the first edition, issued in 2003. This edition includes the following main technical changes with regard to the previous edition: a) test method of test duty III for verification of breaking capacity is reviewed.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60077-4:2019(Main)
Railway applications - Electric equipment for rolling stock - Part 4: Electrotechnical components - Rules for AC circuit-breakers
SIST EN IEC 60077-4:2020

IEC 60077-4:2019 is available as IEC 60077-4:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60077-4:2019 gives rules for AC circuit-breakers, the main contacts of which are connected to AC overhead contact lines; the nominal voltage of these circuits being in accordance with IEC 60850. This document, together with IEC 60077-2, states specifically: a) the characteristics of the circuit-breakers; b) the service conditions with which circuit-breakers comply with reference to: - operation and behaviour in normal service; - operation and behaviour in short-circuit; - dielectric properties; c) the tests for confirming the compliance of the components with the characteristics under the service conditions and the methods to be adopted for these tests d). the information to be marked on, or given with the circuit-breaker. This second edition cancels and replaces the first edition, issued in 2003. This edition includes the following main technical changes with regard to the previous edition: a) standard values of transient recovery voltages and test procedure are reviewed; b) procedure of verification of temperature rise is changed; c) air-tightness test as type test, insulation resistance measurement are added

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60310:2016/AC:2018-03(Corrigendum)
Railway applications - Traction transformers and inductors on board rolling Stock
SIST EN 60310:2016/AC:2019

IEC - IEC parallel corrigendum.

  • Corrigendum
    3 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60077-2:2017(Main)
Railway applications - Electric equipment for rolling stock - Part 2: Electrotechnical components - General rules
SIST EN 60077-2:2018

NEW!IEC 60077-2:2017 is available as IEC 60077-2:2017 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60077-2:2017 provides general rules for all electrotechnical components installed in power circuits, auxiliary circuits, control and indicating circuits, etc., on railway rolling stock. The purpose of this document is to adapt the general rules given in IEC 60077-1 to all electrotechnical components for rolling stock, in order to obtain uniformity of requirements and tests for the corresponding range of components. This new edition includes the following main technical changes with regard to the previous edition: short circuit breaking capacity; rated short-time withstand current; critical currents range; specification of climatic conditions. This standard is to be read in conjunction with IEC 60077-1:2017.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61373:2010/AC:2017-09(Corrigendum)
Railway applications - Rolling stock equipment - Shock and vibration tests
SIST EN 61373:2010/AC:2018
  • Corrigendum
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 62580-1:2016/A11:2017(Amendment)
Electronic railway equipment - On-board multimedia and telematic subsystems for railways - Part 1: General architecture
SIST EN 62580-1:2017/A11:2017

2017-06-01 - D156/024 - Approves publication of Annex ZZ (see BT156/DG10384/DV)
Annex ZZ to be published once approved by BTas an Amendment to the mother standard, this in view of the submission to the EC for citation in the OJEU under Directive 2008/57/EC.
2021: CLC legacy converted by DCLab NISOSTS

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61375-3-4:2014/A11:2017(Amendment)
Electronic railway equipment - Train communication network (TCN) - Part 3-4: Ethernet Consist Network (ECN)
SIST EN 61375-3-4:2014/A11:2017

D156/C020: Publication of Annex ZZ, this in view of the submission to the EC for citation in the OJEU under Directive 2008/57/EC.
2021: CLC legacy converted by DCLab NISOSTS

  • Amendment
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61375-2-3:2015/A11:2017(Amendment)
Electronic railway equipment - Train communication network (TCN) - Part 2-3: TCN communication profile
SIST EN 61375-2-3:2015/A11:2017:2017

D156/C020: Publication of Annex ZZ, this in view of the submission to the EC for citation in the OJEU under Directive 2008/57/EC.
2021: CLC legacy converted by DCLab NISOSTS

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day