EN 60851-6:2012
(Main)Winding wires - Test methods - Part 6: Thermal properties
Winding wires - Test methods - Part 6: Thermal properties
IEC 60851-6:2012 specifies the following tests: - Test 9: Heat shock; - Test 10: Cut-through; - Test 15: Temperature index; - Test 21: Loss of mass. For definitions, general notes on methods of test and the complete series of methods of test for winding wires, see IEC 60851-1. Keyword: winding wires
Wickeldrähte - Prüfverfahren - Teil 6: Thermische Eigenschaften
Fils de bobinage - Méthodes d'essai - Partie 6: Propriétés thermiques
La CEI 60851-6:2012 concerne les essais suivants: - Essai 9: Choc thermique; - Essai 10: Thermoplasticité; - Essai 15: Indice de température; - Essai 21: Perte de masse. Pour les définitions, les généralités concernant les méthodes d'essai et les séries complètes des méthodes d'essai des fils de bobinage, voir la CEI 60851-1. Mot clé: fils de bobinage
Navijalne žice - Preskusne metode - 6. del: Toplotne lastnosti
Ta del standarda IEC 60862 določa praktične napotke za uporabo radiofrekvenčnih (SAW) filtrov, ki se uporabljajo na področju telekomunikacij, merilne opreme, radarskih sistemov in potrošniških proizvodov. Za splošne informacije, standardne vrednosti in preskusne pogoje se uporablja standard IEC 60862-1. Radiofrekvenčni filtri se zdaj pogosto uporabljajo za različne namene, kot so TV, satelitske komunikacije, optične komunikacije, mobilne komunikacije itd. Radiofrekvenčni filtri imajo različne specifikacije, kljub temu pa jih je mogoče razvrstiti v nekaj temeljnih kategorij. Ta del standarda IEC 60862 zajema različne vrste konfiguracij filtrov s frekvenčnim območjem delovanja od približno 10 MHz do 3 GHz in relativno pasovno širino približno od 0,02 % do 50 % srednje frekvence.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2012
1DGRPHãþD
SIST EN 60851-6:2001
SIST EN 60851-6:2001/A1:2001
SIST EN 60851-6:2001/A2:2004
Navijalne žice - Preskusne metode - 6. del: Toplotne lastnosti
Winding wires - Test methods - Part 6: Thermal properties
Wickeldrähte - Prüfverfahren - Teil 6: Thermische Eigenschaften
Fils de bobinage - Méthodes d'essai - Partie 6: Propriétés thermiques
Ta slovenski standard je istoveten z: EN 60851-6:2012
ICS:
29.060.10 Žice Wires
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 60851-6
NORME EUROPÉENNE
August 2012
EUROPÄISCHE NORM
ICS 29.060.10 Supersedes EN 60851-6:1996 + A1:1997 + A2:2004
English version
Winding wires -
Test methods -
Part 6: Thermal properties
(IEC 60851-6:2012)
Fils de bobinage - Wickeldrähte -
Méthodes d'essai - Prüfverfahren -
Partie 6: Propriétés thermiques Teil 6: Thermische Eigenschaften
(CEI 60851-6:2012) (IEC 60851-6:2012)
This European Standard was approved by CENELEC on 2012-06-27. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60851-6:2012 E
Foreword
The text of document 55/1312/FDIS, future edition 3 of IEC 60851-6, prepared by IEC/TC 55 "Winding
wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
(dop) 2013-03-27
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2015-06-27
• latest date by which the national
standards conflicting with the
document have to be withdrawn
This document supersedes EN 60851-6:1996 + A1:1997 + A2:2004.
EN 60851-6:1996 + A1:1997 + A2:2004:
- deletion of Table 2: Heating period in Test 10: Cut-through;
- revision to Test 15, where the temperature index requirements for all winding wire constructions
have a common reference.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60851-6:2012 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated :
IEC 60851-1 NOTE Harmonised as EN 60851-1.
- 3 - EN 60851-6:2012
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
IEC 60172 - Test procedure for the determination of the EN 60172 -
temperature index of enamelled winding
wires
IEC 60851-3 2009 Winding wires - Test methods - EN 60851-3 2009
Part 3: Mechanical properties
IEC 60851-5 2008 Winding wires - Test methods - EN 60851-5 2008
+ A1 2011 Part 5: Electrical properties + A1 2011
IEC 60851-6 ®
Edition 3.0 2012-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Winding wires – Test methods –
Part 6: Thermal properties
Fils de bobinage – Méthodes d'essai –
Partie 6: Propriétés thermiques
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX M
ICS 29.060.10 ISBN 978-2-83220-091-9
– 2 – 60851-6 © IEC:2012
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Test 9: Heat shock (applicable to enamelled and tape wrapped wire) . 6
3.1 General . 6
3.2 Specimen . 6
3.2.1 Round wire . 6
3.2.2 Rectangular wire . 7
3.3 Procedure . 7
3.4 Result . 7
4 Test 10: Cut-through (applicable to enamelled round wire with a nominal conductor
diameter over 0,100 mm up to and including 1,600 mm and tape wrapped round
wire) . 7
4.1 General . 7
4.2 Equipment . 7
4.3 Procedure . 7
5 Test 15: Temperature index . 8
6 Test 21: Loss of mass (applicable to enamelled round wire) . 8
6.1 General . 8
6.2 Specimen . 8
6.3 Procedure . 8
Annex A (informative) High temperature failure test (applicable to enamelled round
wire) . 11
Bibliography . 13
Figure 1 – Compression device for the cut-through test . 10
Table 1 – Magnification . 7
Table 2 – Loads applied to the crossing point . 8
Table A.1 – Test voltage . 11
60851-6 © IEC:2012 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
WINDING WIRES – TEST METHODS –
Part 6: Thermal properties
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60851-6 has been prepared by IEC technical committee 55:
Winding wires.
This third edition cancels and replaces the second edition, published in 1996 and constitutes
a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
– Deletion of Table 2: Heating period in Test 10: Cut-through
– Revision to Test 15, where the temperature index requirements for all winding wire
constructions have a common reference.
– 4 – 60851-6 © IEC:2012
The text of this standard is based on the following documents:
FDIS Report on voting
55/1312/FDIS 55/1330/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all the parts in the IEC 60851 series, published under the general title Winding wires
– Test methods, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.